Changes for page 3.3 Control
Last modified by Admin on 2025/04/09 12:14
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -471,7 +471,7 @@ 471 471 * Allow charging only when the "Ready to charge" signal is set – charging contactor will open if "Ready to charge" signal is cleared; 472 472 * Delay before starting charging – a time delay T,,on,, before closing the charging contactor and the allow charging contactor, millisecond; 473 473 * Delay before stopping charging – a time delay T,,off,, before opening the charging contactor, millisecond; 474 -* Control the precharging contactor – a flag that allows control of the precharging contactor while closing the charge contactor; 474 +* Control the precharging contactor – a flag that allows control of the precharging contactor while closing the charge contactor (see [[Precharge>>path:#HPrecharge]]); 475 475 * Errors 1, 2 to open the charging contactor – bitfields to choose the errors which will open the charging contactor; 476 476 * Use custom delays before stopping charging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors; 477 477 * Custom delay: <error> – delay for specific error, millisecond; ... ... @@ -510,8 +510,6 @@ 510 510 **Note: **when errors occur in the system, the **Discharge **contactor opens either immediately or with the delay T,,off,, (depends on the settings described below). 511 511 ))) 512 512 513 -The device supports controlling the precharging contactor (see [[Precharge>>doc:||anchor="HPrecharge"]]). 514 - 515 515 To change the parameters of the battery discharge control algorithm, select the "Control → Discharge" section: 516 516 517 517 [[image:1735064038329-836.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="273" width="800"]] ... ... @@ -526,7 +526,7 @@ 526 526 * Allow charging only when the "Ready to discharge" signal is set – discharging contactor will open if "Ready to discharge" signal is cleared; 527 527 * Delay before starting discharging – a time delay T,,on,, before closing the discharging contactor, millisecond; 528 528 * Delay before stopping discharging – a time delay T,,off,, before opening the discharging contactor, millisecond; 529 -* Control the precharging contactor – a flag that allows control of the precharging contactor while closing the discharge contactor; 527 +* Control the precharging contactor – a flag that allows control of the precharging contactor while closing the discharge contactor (see [[Precharge>>doc:||anchor="HPrecharge"]]); 530 530 * Errors 1, 2 to open the discharging contactor – bitfields to choose the errors which will open the discharging contactor; 531 531 * Use custom delays before stopping discharging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors; 532 532 * Custom delay: <error> – specific error delay, millisecond; ... ... @@ -581,11 +581,6 @@ 581 581 * the battery voltage is out of range; 582 582 * the errors are detected (configured in the "Errors 1, 2 ..." bitfields). 583 583 584 -(% class="box infomessage" %) 585 -((( 586 -**Note: **when errors occur in the system, the **Discharge (AUX) **contactor opens either immediately or with the delay T,,off,, (depends on the settings described below). 587 -))) 588 - 589 589 To change the parameters of the powering of external equipment, select the "Control → Discharge (AUX)" section: 590 590 591 591 [[image:1735066190419-838.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="161" width="800"]] ... ... @@ -602,7 +602,7 @@ 602 602 * Switch off the discharging (AUX) contactor if the battery voltage is out of the range; 603 603 * Minimum battery voltage, V; 604 604 * Maximum battery voltage, V; 605 -* Errors 1, 2 to open the auxiliary discharging contactor – bitfields to choose the errors which will open the auxiliary discharging contactor ;598 +* Errors 1, 2 to open the auxiliary discharging contactor – bitfields to choose the errors which will open the auxiliary discharging contactor. 606 606 607 607 === Cell balancing === 608 608 ... ... @@ -624,7 +624,10 @@ 624 624 * the voltage on the cell is less than the balancing stop voltage; 625 625 * the difference between the voltage on the cell and the minimum voltage among the battery cells is less than the balancing stop threshold. 626 626 620 +(% class="box infomessage" %) 621 +((( 627 627 If the “High logic temperature” occurs, then the balancing of the cells connected to the overheated BMS Logic device will not be performed. 623 +))) 628 628 629 629 The BMS Main 3 can enable the cell balancing by the external “Balancing request” signal. Balancing process will be started to cells which the voltage is higher than the balancing start voltage and the difference between the cell voltage and the minimum voltage among all the cells is greater than the balancing stop threshold. 630 630 ... ... @@ -641,9 +641,6 @@ 641 641 ** Balance on charge – balancing is performed while and after the charging (in the “Charge ON” and “Charge OFF” states); 642 642 ** Balance on charge or relaxed - balancing is performed while and after the charging and in the relaxed state (in “Charge ON”, “Charge OFF”, “Relaxed (after charging)” and “Relaxed (after discharging)” states); 643 643 ** Balance always – balancing is always performed regardless the battery state; 644 - 645 -[[image:1735065666891-686.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="132" width="800"]] 646 - 647 647 * Balancing condition: 648 648 ** Automatic – balancing will be performed automatically if needed conditions are met; 649 649 ** On balancing request – balancing will start only if a remote request is received. In this case cells will start to balance regardless the "Voltage deviation to start balancing" value;