Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -431,27 +431,27 @@
431	431	* On charger connected – charging is allowed when there is a signal “Charger connected”;
432	432	* On charge request – charging is allowed when there is a signal “Charge request”.
433	433
434		-If the "**Always on**" algorithm is selected, the charging contactor is always closed. If at least one of the errors from the "Errors 1, 2 ..." bitfield appears or one of the signals:
	434	+If the "**Always on**" algorithm is selected, the charging contactor and the allow charging contactor are always closed. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
435	435
436	436	* Service reset;
437	437	* Power down request;
438	438	* Inhibit charging,
439	439
440		-contactor are open (no current flows).
	440	+both contactors are open (no current flows).
441	441
442	442	When the algorithm "**On charger connected**" is selected, the control is performed as follows:
443	443
444		-* If there is a signal “Charger connected” and there are no errors (see the list above), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
	444	+* If there is a signal “Charger connected” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
445	445	* If the signal “Charger connected” disappears, the allow charging contactor opens and after the delay time T,,off,, the charging contactor opens;
446	446	* If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
447		-* If errors in the list above occur the charging contactor and allow charging contactor open.
	447	+* If errors from the "Errors 1, 2 ..." bitfields occur the charging contactor and allow charging contactor open.
448	448
449	449	When the "**On charge request**" algorithm selected, the control is performed as follows:
450	450
451		-* If there is a signal “Charge request” and there are no errors (see the list above), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
	451	+* If there is a signal “Charge request” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
452	452	* If the signal “Charge request” disappears, the allow charging contactor opens and after the delay time T,,off,, the charging contactor opens;
453	453	* If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
454		-* If errors in the list above occur the charging contactor and allow charging contactor open.
	454	+* If errors from the "Errors 1, 2 ..." bitfields occur the charging contactor and allow charging contactor open.
455	455
456	456	(% class="box infomessage" %)
457	457	(((
...	...	@@ -488,26 +488,8 @@
488	488	* On charger disconnected – load is connected when there is no signal “Charger connected”;
489	489	* On discharge request – load is connected when there is signal “Discharge request”.
490	490
491		-When the algorithm "**Always on**" is selected, the discharging contactor is always closed. If at least one of the errors appears:
	491	+When the algorithm "**Always on**" is selected, the discharging contactor is always closed. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
492	492
493		-* Undervoltage;
494		-* Overvoltage (optional);
495		-* Overcurrent;
496		-* High temperature (DCH);
497		-* Low temperature (DCH) (optional);
498		-* HYG offline (optional);
499		-* Combilift offline (optional);
500		-* Spirit offline (optional);
501		-* Spirit charger error (optional);
502		-* Short circuit (optional);
503		-* High contactor temperature (optional);
504		-* Unallowable charging;
505		-* DCH contactor cycles error;
506		-* Precharge error (optional);
507		-* Critical error
508		-
509		-or one of the signals:
510		-
511	511	* Service reset
512	512	* Power down request
513	513	* Inhibit discharging
...	...	@@ -516,13 +516,13 @@
516	516
517	517	If the algorithm "**On charger disconnected**" is selected, the control is performed as follows:
518	518
519		-* if there is no signal “Charger connected”, the charging contactor is open and there are no errors (see the list above), then through the delay time T,,on,, the discharging contactor closes;
520		-* If the signal “Charger connected” appears or errors occur (see the list above), then after the delay time T,,off,, the discharging contactor opens.
	501	+* if there is no signal “Charger connected”, the charging contactor is open and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the discharging contactor closes;
	502	+* If the signal “Charger connected” appears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the discharging contactor opens.
521	521
522	522	When the "**On discharge request**" algorithm selected, the control is performed as follows:
523	523
524	524	* if there is signal “Discharge request”, the charging contactor is open and there are no errors (see the list above), then through the delay time T,,on,, the discharging contactor closes;
525		-* If the signal “Discharge request” disappears or errors occur (see the list above), then after the delay time T,,off,, the discharging contactor opens.
	507	+* If the signal “Discharge request” disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the discharging contactor opens.
526	526
527	527	(% class="box infomessage" %)
528	528	(((