Skip to Content

Changes for page 3.3 Control

Last modified by Admin on 2025/04/09 12:14
From version 33.3
edited by Admin
on 2025/02/11 13:19
Change comment: There is no comment for this version
To version 33.7
edited by Admin
on 2025/02/11 13:24
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -431,24 +431,8 @@
431 431  * On charger connected – charging is allowed when there is a signal “Charger connected”;
432 432  * On charge request – charging is allowed when there is a signal “Charge request”.
433 433  
434 -If the "**Always on**" algorithm is selected, the charging contactor and the allow charging contactor are always closed. If at least one of the errors appears:
434 +If the "**Always on**" algorithm is selected, the charging contactor and the allow charging contactor are always closed. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
435 435  
436 -* Overvoltage;
437 -* Overcurrent;
438 -* High temperature (CH);
439 -* Low temperature (CH);
440 -* HYG offline (optional);
441 -* Combilift offline (optional);
442 -* Spirit offline (optional);
443 -* Spirit charger error (optional);
444 -* Short circuit (optional);
445 -* High contactor temperature (optional);
446 -* CH contactor cycles error;
447 -* Precharge error (optional);
448 -* Critical error
449 -
450 -or one of the signals:
451 -
452 452  * Service reset;
453 453  * Power down request;
454 454  * Inhibit charging,
... ... @@ -457,14 +457,14 @@
457 457  
458 458  When the algorithm "**On charger connected**" is selected, the control is performed as follows:
459 459  
460 -* If there is a signal “Charger connected” and there are no errors (see the list above), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
444 +* If there is a signal “Charger connected” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
461 461  * If the signal “Charger connected” disappears, the allow charging contactor opens and after the delay time T,,off,, the charging contactor opens;
462 462  * If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
463 -* If errors in the list above occur the charging contactor and allow charging contactor open.
447 +* If errors from the "Errors 1, 2 ..." bitfields occur the charging contactor and allow charging contactor open.
464 464  
465 465  When the "**On charge request**" algorithm selected, the control is performed as follows:
466 466  
467 -* If there is a signal “Charge request” and there are no errors (see the list above), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
451 +* If there is a signal “Charge request” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
468 468  * If the signal “Charge request” disappears, the allow charging contactor opens and after the delay time T,,off,, the charging contactor opens;
469 469  * If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
470 470  * If errors in the list above occur the charging contactor and allow charging contactor open.