Changes for page 3.3 Control

Last modified by Admin on 2025/04/09 12:14

From 33.1 to 33.2 From 37.1 to 38.1

From version 33.2

edited by Admin
on 2025/02/11 13:18

Change comment: There is no comment for this version

To version 37.1

edited by Admin
on 2025/02/11 16:56

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -70,7 +70,7 @@
  * Minimal SOC – the battery SOC is assumed to be the minimum SOC among the cells;
  * Average SOC – the battery SOC is taken equal to the arithmetic average of the cell SOC;
--* Min-Max SOC – the battery SOC is calculated based on the minimum and maximum SOC of the cells. Final SOC will be a) 100% if any cell have 100% SOC, b) 0% if any cell have 0% SOC;
++* Min-Max SOC – the battery SOC is calculated based on the minimum and maximum SOC of the cells. Final SOC will be a) 100% if any cell has 100% SOC, b) 0% if any cell has 0% SOC;
  * Max-Min SOC – the battery SOC is calculated based on the minimum and maximum SOC of the cells. Final SOC will be a) 100% if all cells have 100% SOC, b) 0% if all cells have 0% SOC;
  Other parameters:
@@ -328,7 +328,7 @@
  * Other contactors are open;
  * There is an error from the the "Errors 1, 2 ..." bitfileds.
--In “Automatic” mode, the main contactor closes by internal charging and discharging algorithms at the same time with ther contactors.
++In “Automatic” mode, the main contactor closes by internal algorithms at the same time with other contactors.
  In “On demand” mode, the main contactor closes by external the “Close Main contactor” request.
@@ -410,10 +410,10 @@
  * Delay before clearing the "Precharge error", second;
  * Lock the "Precharge error" – a flag to block the error until the device is restarted.
--“Precharge error” generation conditions:
++“Precharge error” generation conditions if any of the following is true:
--* the precharge current does not decrease after "Number of precharging attempts";
--* voltages before and after contactors are not equal after "Number of precharging attempts";
++* the precharge current does not decrease during the "Precharge time" after "Number of precharging attempts";
++* voltages before and after contactors are not equal during the "Precharge time" after "Number of precharging attempts";
  * power dissipated on the precharge resistor is above the maximum value during the “Delay before setting the 'Precharge error' when checking power” time.
  (% class="box warningmessage" %)
@@ -431,24 +431,8 @@
  * On charger connected – charging is allowed when there is a signal “Charger connected”;
  * On charge request – charging is allowed when there is a signal “Charge request”.
--If the "**Always on**" algorithm is selected, the charging contactor and the allow charging contactor are always closed. If at least one of the errors appears:
++If the "**Always on**" algorithm is selected, the charging contactor and the allow charging contactor are always closed. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
--* Overvoltage;
--* Overcurrent;
--* High temperature (CH);
--* Low temperature (CH);
--* HYG offline (optional);
--* Combilift offline (optional);
--* Spirit offline (optional);
--* Spirit charger error (optional);
--* Short circuit (optional);
--* High contactor temperature (optional);
--* CH contactor cycles error;
--* Precharge error (optional);
--* Critical error
--
--or one of the signals:
--
  * Service reset;
  * Power down request;
  * Inhibit charging,
@@ -457,17 +457,17 @@
  When the algorithm "**On charger connected**" is selected, the control is performed as follows:
--* If there is a signal “Charger connected” and there are no errors (see the list above), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
++* If there is a signal “Charger connected” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
  * If the signal “Charger connected” disappears, the allow charging contactor opens and after the delay time T,,off,, the charging contactor opens;
  * If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
--* If errors in the list above occur the charging contactor and allow charging contactor open.
++* If errors from the "Errors 1, 2 ..." bitfields occur the charging contactor and allow charging contactor open.
  When the "**On charge request**" algorithm selected, the control is performed as follows:
--* If there is a signal “Charge request” and there are no errors (see the list above), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
++* If there is a signal “Charge request” and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the charging contactor and the allow charging contactor close;
  * If the signal “Charge request” disappears, the allow charging contactor opens and after the delay time T,,off,, the charging contactor opens;
  * If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
--* If errors in the list above occur the charging contactor and allow charging contactor open.
++* If errors from the "Errors 1, 2 ..." bitfields occur the charging contactor and allow charging contactor open.
  (% class="box infomessage" %)
  (((
@@ -504,26 +504,8 @@
  * On charger disconnected – load is connected when there is no signal “Charger connected”;
  * On discharge request – load is connected when there is signal “Discharge request”.
--When the algorithm "**Always on**" is selected, the discharging contactor is always closed. If at least one of the errors appears:
++When the algorithm "**Always on**" is selected, the discharging contactor is always closed. If at least one of the errors from the "Errors 1, 2 ..." bitfields appears or one of the signals:
--* Undervoltage;
--* Overvoltage (optional);
--* Overcurrent;
--* High temperature (DCH);
--* Low temperature (DCH) (optional);
--* HYG offline (optional);
--* Combilift offline (optional);
--* Spirit offline (optional);
--* Spirit charger error (optional);
--* Short circuit (optional);
--* High contactor temperature (optional);
--* Unallowable charging;
--* DCH contactor cycles error;
--* Precharge error (optional);
--* Critical error
--
--or one of the signals:
--
  * Service reset
  * Power down request
  * Inhibit discharging
@@ -532,13 +532,13 @@
  If the algorithm "**On charger disconnected**" is selected, the control is performed as follows:
--* if there is no signal “Charger connected”, the charging contactor is open and there are no errors (see the list above), then through the delay time T,,on,, the discharging contactor closes;
--* If the signal “Charger connected” appears or errors occur (see the list above), then after the delay time T,,off,, the discharging contactor opens.
++* if there is no signal “Charger connected”, the charging contactor is open and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the discharging contactor closes;
++* If the signal “Charger connected” appears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the discharging contactor opens.
  When the "**On discharge request**" algorithm selected, the control is performed as follows:
--* if there is signal “Discharge request”, the charging contactor is open and there are no errors (see the list above), then through the delay time T,,on,, the discharging contactor closes;
--* If the signal “Discharge request” disappears or errors occur (see the list above), then after the delay time T,,off,, the discharging contactor opens.
++* if there is signal “Discharge request”, the charging contactor is open and there are no errors (see the "Errors 1, 2 ..." bitfields), then through the delay time T,,on,, the discharging contactor closes;
++* If the signal “Discharge request” disappears or errors occur (see the "Errors 1, 2 ..." bitfields), then after the delay time T,,off,, the discharging contactor opens.
  (% class="box infomessage" %)
  (((
@@ -545,7 +545,7 @@
  **Note: **when errors occur in the system, the **Discharge **contactor opens either immediately or with the delay T,,off,, (depends on the settings described below).
  )))
--The device supports controlling the precharging contactor. The duration of switching on the precharging contactor before closing the discharging (load) contactor is adjusted.
++The device supports controlling the precharging contactor (see [[Precharge>>doc:||anchor="HPrecharge"]]).
  To change the parameters of the battery discharge control algorithm, select the "Control → Discharge" section:
@@ -614,7 +614,7 @@
  * the battery has low SOC;
  * the battery voltage is out of range;
--* the battery system errors are detected.
++* the errors are detected (configured in the "Errors 1, 2 ..." bitfields).
  (% class="box infomessage" %)
  (((
@@ -762,7 +762,7 @@
  * the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before stopping the heater” time.
--If there is the "Heater" signal, the heater contactor closes and/or a signal is output to the corresponding digital output.
++If there is the "Heater" signal, the heater contactor closes and/or a signal is set to the corresponding digital output.
  === Cooler ===
@@ -789,7 +789,7 @@
  * the maximum temperature among all cells of the battery is less than the “Tolerant cell temperature” value during the “Delay before stopping the cooler” time.
--If there is the "Cooler" signal, the cooler contactor closes and/or a signal is output to the corresponding digital output.
++If there is the "Cooler" signal, the cooler contactor closes and/or a signal is set to the corresponding digital output.
  === High voltage ===

Changes for page 3.3 Control

Summary

Details

Applications

Navigation

Table of Contents