Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 1 removed)
  • 1735064038329-836.png

Details

Page properties

Content

...	...	@@ -359,8 +359,6 @@
359	359
360	360	=== Charging status ===
361	361
362		-* Current corresponding to charging – a current level to generate the "Charging current present" signal, A;
363		-* Current corresponding to no charging – a current level to clear the "Charging current present" signal, A;
364	364	* Voltage to clear the “Ready to charge” – a threshold voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
365	365	* Voltage to reset the “Ready to charge” – a tolerant voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
366	366	* Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0.
...	...	@@ -374,8 +374,6 @@
374	374
375	375	=== Discharging status ===
376	376
377		-* Current corresponding to discharging – a current level to generate the "Discharging current present" signal, А;
378		-* Current indicating no discharging – a current level to clear the "Discharging current present" signal, А;
379	379	* Voltage to clear the “Ready to discharge” – a threshold voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
380	380	* Voltage to reset the “Ready to discharge” – a tolerant voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
381	381
...	...	@@ -448,9 +448,11 @@
448	448	** On charger connected – charging is allowed when there is a signal “Charger connected”;
449	449	** On charge request – charging is allowed when there is a signal “Charge request”;
450	450	* Allow charging only when the "Ready to charge" signal is set – charging contactor will open if "Ready to charge" signal is cleared;
	447	+* Current corresponding to charging – a current level to generate the "Charging current present" signal, A;
	448	+* Current corresponding to no charging – a current level to clear the "Charging current present" signal, A;
451	451	* Delay before starting charging – a time delay T,,on,, before closing the charging contactor and the allow charging contactor, millisecond;
452	452	* Delay before stopping charging – a time delay T,,off,, before opening the charging contactor, millisecond;
453		-* Control the precharging contactor – a flag that allows control of the precharging contactor while closing the charge contactor;
	451	+* Control the precharging contactor – a flag that allows control of the precharging contactor;
454	454	* Errors 1, 2 to open the charging contactor – bitfields to choose the errors which will open the charging contactor;
455	455	* Use custom delays before stopping charging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors;
456	456	* Custom delay: <error> – delay for specific error, millisecond;
...	...	@@ -511,7 +511,7 @@
511	511
512	512	To change the parameters of the battery discharge control algorithm, select the "Control → Discharge" section:
513	513
514		-[[image:1735064038329-836.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="273" width="800"]]
	512	+[[image:1733323750262-841.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="360" width="800"]]
515	515
516	516	In this section:
517	517
...	...	@@ -520,14 +520,16 @@
520	520	** Always on – load is always connected;
521	521	** On charger disconnected – load is connected when there is no signal “Charger connected”;
522	522	** On discharge request – load is connected when there is signal “Discharge request”;
523		-* Allow charging only when the "Ready to discharge" signal is set – discharging contactor will open if "Ready to discharge" signal is cleared;
	521	+* Current corresponding to discharging – a current level to generate the "Discharging current present" signal, А;
	522	+* Current indicating no discharging – a current level to clear the "Discharging current present" signal, А;
524	524	* Delay before starting discharging – a time delay T,,on,, before closing the discharging contactor, millisecond;
525	525	* Delay before stopping discharging – a time delay T,,off,, before opening the discharging contactor, millisecond;
526		-* Control the precharging contactor – a flag that allows control of the precharging contactor while closing the discharge contactor;
527		-* Errors 1, 2 to open the discharging contactor – bitfields to choose the errors which will open the discharging contactor;
528	528	* Use custom delays before stopping discharging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors;
529	529	* Custom delay: <error> – specific error delay, millisecond;
530	530	* Switch off the discharging contactor on errors without delay – a flag to protectively open the discharging contactor without a delay. In the opposite case, when an error is detected, the discharging contactor opens always with the delay “Delay before stopping discharging”.
	528	+* Precharge time – a duration of closing the precharge contactor before closing the discharging contactor, millisecond;
	529	+* Check voltages before and after contactors to finish precharging – a flag to check the voltages before and after contactors to ensure that precharge process has finished and it is allowed to close the discharging contactor;
	530	+* Minimum voltage difference to finish precharging – minimal voltage difference before and after contactors at which precharge process is meant to be finished, V;
531	531
532	532	=== Charge/Discharge ===
533	533

1735064038329-836.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.admin

Size

...	...	@@ -1,1 +1,0 @@
1		-62.0 KB

Content