Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -407,9 +407,9 @@
407	407
408	408	or one of the signals:
409	409
410		-* Service reset;
411		-* Power down request;
412		-* Inhibit charging,
	410	+* Service reset
	411	+* Power down request
	412	+* Inhibit charging
413	413
414	414	both contactors are open (no current flows).
415	415
...	...	@@ -427,10 +427,7 @@
427	427	* If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
428	428	* If errors in the list above occur the charging contactor and allow charging contactor open.
429	429
430		-(% class="box infomessage" %)
431		-(((
432		-Note: when errors occur in the system, the **charging **contactor opens either immediately or with the delay T,,off,, (depends on the settings described below).
433		-)))
	430	+Note – When errors occur in the system, the charging contactor opens either immediately or with the delay T,,off,, (depends on the settings described below).
434	434
435	435	To change the parameters of the battery charge control algorithm, select the "Control → Charge" section:
436	436
...	...	@@ -448,10 +448,10 @@
448	448	* Current corresponding to no charging – a current level to clear the "Charging current present" signal, A;
449	449	* Delay before starting charging – a time delay T,,on,, before closing the charging contactor and the allow charging contactor, millisecond;
450	450	* Delay before stopping charging – a time delay T,,off,, before opening the charging contactor, millisecond;
451		-* Control the precharging contactor – a flag that allows control of the precharging contactor while closing the charge contactor;
452		-* Errors 1, 2 to open the charging contactor – bitfields to choose the errors which will open the charging contactor;
	448	+* Control the precharging contactor – a flag that allows control of the precharging contactor;
	449	+* Errors 1, 2 to open the charging contactor – bitfields to choose the errors which will open the charging contactor
453	453	* Use custom delays before stopping charging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors;
454		-* Custom delay: <error> – delay for specific error, millisecond;
	451	+* Custom delay: <error> – specific error delay, millisecond;
455	455	* Switch off the charging contactor on errors without delay – a flag to protectively open the charging contactor without a delay. In the opposite case, when an error is detected, the charging contactor opens always with the delay “Delay before stopping charging”;
456	456
457	457	=== Discharge ===
...	...	@@ -500,10 +500,7 @@
500	500	* if there is signal “Discharge request”, the charging contactor is open and there are no errors (see the list above), then through the delay time T,,on,, the discharging contactor closes;
501	501	* If the signal “Discharge request” disappears or errors occur (see the list above), then after the delay time T,,off,, the discharging contactor opens.
502	502
503		-(% class="box infomessage" %)
504		-(((
505		-**Note:** in case of errors in the system operation, **discharging **contactor opens either immediately or with a delay T,,off,, (depends on the settings described below).
506		-)))
	500	+Note – In case of errors in the system operation, the opening of the discharging contactor is performed either immediately or with a delay T,,off,, (depends on the settings described below).
507	507
508	508	The device supports controlling the precharging contactor. The duration of switching on the precharging contactor before closing the discharging (load) contactor is adjusted.
509	509
...	...	@@ -522,11 +522,12 @@
522	522	* Current indicating no discharging – a current level to clear the "Discharging current present" signal, А;
523	523	* Delay before starting discharging – a time delay T,,on,, before closing the discharging contactor, millisecond;
524	524	* Delay before stopping discharging – a time delay T,,off,, before opening the discharging contactor, millisecond;
525		-* Control the precharging contactor – a flag that allows control of the precharging contactor while closing the discharge contactor;
526		-* Errors 1, 2 to open the discharging contactor – bitfields to choose the errors which will open the charging contactor;
527	527	* Use custom delays before stopping discharging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors;
528	528	* Custom delay: <error> – specific error delay, millisecond;
529	529	* Switch off the discharging contactor on errors without delay – a flag to protectively open the discharging contactor without a delay. In the opposite case, when an error is detected, the discharging contactor opens always with the delay “Delay before stopping discharging”.
	522	+* Precharge time – a duration of closing the precharge contactor before closing the discharging contactor, millisecond;
	523	+* Check voltages before and after contactors to finish precharging – a flag to check the voltages before and after contactors to ensure that precharge process has finished and it is allowed to close the discharging contactor;
	524	+* Minimum voltage difference to finish precharging – minimal voltage difference before and after contactors at which precharge process is meant to be finished, V;
530	530
531	531	=== Charge/Discharge ===
532	532