Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 1 removed)
  • 1735063563460-549.png

Details

Page properties

Content

...	...	@@ -302,6 +302,8 @@
302	302
303	303	I,,continuous,, = Maximum CONTINUOUS discharge current × K,,dc,,
304	304
	305	+
	306	+
305	305	=== Main contactor ===
306	306
307	307	The BMS Main 3 device controls the main contactor. The main contactor is usually placed in the common (minus) battery line for opening the charge and discharge circuits in case of sealing of the charging or discharging contactors.
...	...	@@ -359,17 +359,8 @@
359	359
360	360	=== Charging status ===
361	361
362		-* Voltage to clear the “Ready to charge” – a threshold voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
363		-* Voltage to reset the “Ready to charge” – a tolerant voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
364		-* Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0.
	364	+TBA
365	365
366		-(% class="box infomessage" %)
367		-(((
368		-**Note:** The allow charging ышптфд closes under two independent conditions:
369		-1) the voltage on the cells reaches the “Voltage to reset the “Ready to charge"” level and
370		-2) the "Delay before recharging" time has passed since the opening of the allow charging contactor.
371		-)))
372		-
373	373	=== Discharging status ===
374	374
375	375	TBA
...	...	@@ -443,11 +443,16 @@
443	443	* Current corresponding to no charging – a current level to clear the "Charging current present" signal, A;
444	444	* Delay before starting charging – a time delay T,,on,, before closing the charging contactor and the allow charging contactor, millisecond;
445	445	* Delay before stopping charging – a time delay T,,off,, before opening the charging contactor, millisecond;
446		-* Control the precharging contactor – a flag that allows control of the precharging contactor;
447	447	* Use custom delays before stopping charging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors;
448	448	* Custom delay: <error> – specific error delay, millisecond;
449	449	* Switch off the charging contactor on errors without delay – a flag to protectively open the charging contactor without a delay. In the opposite case, when an error is detected, the charging contactor opens always with the delay “Delay before stopping charging”;
	442	+* Control the precharging contactor – a flag that allows control of the precharging contactor;
	443	+* Voltage to clear the “Ready to charge” – a threshold voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
	444	+* Voltage to reset the “Ready to charge” – a tolerant voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
	445	+* Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0.
450	450
	447	+Note – The allow charging contactor closes under two independent conditions: 1) the voltage on the cells reaches the “Voltage to reset the “Ready to charge"” level and 2) the "Delay before recharging" time has passed since the opening of the allow charging contactor.
	448	+
451	451	=== Discharge ===
452	452
453	453	The device controls the discharging contactor to connect battery to the load.

1735063563460-549.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.admin

Size

...	...	@@ -1,1 +1,0 @@
1		-59.6 KB

Content