Changes for page 3.3 Control

Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 1 added, 0 removed)
  • 1735063563460-549.png

Details

Page properties

Content

...	...	@@ -359,11 +359,21 @@
359	359
360	360	=== Charging status ===
361	361
362		-TBA
	362	+* Voltage to clear the “Ready to charge” – a threshold voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
	363	+* Voltage to reset the “Ready to charge” – a tolerant voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
	364	+* Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0.
363	363
	366	+(% class="box infomessage" %)
	367	+(((
	368	+**Note:** The "Allow charging" signal activates under two independent conditions:
	369	+1) the voltage on the cells reaches the “Voltage to reset the “Ready to charge"” level and
	370	+2) the "Delay before recharging" time has passed since the opening of the allow charging contactor.
	371	+)))
	372	+
364	364	=== Discharging status ===
365	365
366		-TBA
	375	+* Voltage to clear the “Ready to discharge” – a threshold voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
	376	+* Voltage to reset the “Ready to discharge” – a tolerant voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
367	367
368	368	=== Precharge ===
369	369
...	...	@@ -397,9 +397,9 @@
397	397
398	398	or one of the signals:
399	399
400		-* Service reset
401		-* Power down request
402		-* Inhibit charging
	410	+* Service reset;
	411	+* Power down request;
	412	+* Inhibit charging,
403	403
404	404	both contactors are open (no current flows).
405	405
...	...	@@ -417,11 +417,14 @@
417	417	* If in the process of charging the voltage on the cell exceeds the “Ready to charge” level, the allow charging contactor opens (while the charging contactor remains closed);
418	418	* If errors in the list above occur the charging contactor and allow charging contactor open.
419	419
420		-Note – When errors occur in the system, the charging contactor opens either immediately or with the delay T,,off,, (depends on the settings described below).
	430	+(% class="box infomessage" %)
	431	+(((
	432	+Note: when errors occur in the system, the **charging **contactor opens either immediately or with the delay T,,off,, (depends on the settings described below).
	433	+)))
421	421
422	422	To change the parameters of the battery charge control algorithm, select the "Control → Charge" section:
423	423
424		-[[image:1733322798914-813.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="327" width="800"]]
	437	+[[image:1735063563460-549.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="262" width="800"]]
425	425
426	426	In this section:
427	427
...	...	@@ -430,20 +430,17 @@
430	430	** Always on – charging is always allowed;
431	431	** On charger connected – charging is allowed when there is a signal “Charger connected”;
432	432	** On charge request – charging is allowed when there is a signal “Charge request”;
	446	+* Allow charging only when the "Ready to charge" signal is set – charging contactor will open if "Ready to charge" signal is cleared;
433	433	* Current corresponding to charging – a current level to generate the "Charging current present" signal, A;
434	434	* Current corresponding to no charging – a current level to clear the "Charging current present" signal, A;
435	435	* Delay before starting charging – a time delay T,,on,, before closing the charging contactor and the allow charging contactor, millisecond;
436	436	* Delay before stopping charging – a time delay T,,off,, before opening the charging contactor, millisecond;
	451	+* Control the precharging contactor – a flag that allows control of the precharging contactor;
	452	+* Errors 1, 2 to open the charging contactor – bitfields to choose the errors which will open the charging contactor;
437	437	* Use custom delays before stopping charging (on errors) – a flag to enable manual settings of time delays T,,off,, for specific errors;
438		-* Custom delay: <error> – specific error delay, millisecond;
	454	+* Custom delay: <error> – delay for specific error, millisecond;
439	439	* Switch off the charging contactor on errors without delay – a flag to protectively open the charging contactor without a delay. In the opposite case, when an error is detected, the charging contactor opens always with the delay “Delay before stopping charging”;
440		-* Control the precharging contactor – a flag that allows control of the precharging contactor;
441		-* Voltage to clear the “Ready to charge” – a threshold voltage level on the cell, V; if the voltage of any cell is above this level, the “Ready to charge” (hence, the “Allow charging”) signal is cleared;
442		-* Voltage to reset the “Ready to charge” – a tolerant voltage level on the cell, V; if all cell voltages are below the tolerant level, the “Ready to charge” (hence, the “Allow charging”) signal is set;
443		-* Delay before recharging – a time after which the previously opened the allow charging contactor closes again, minute; to disable the operation by timeout set "Delay before recharging" to 0.
444	444
445		-Note – The allow charging contactor closes under two independent conditions: 1) the voltage on the cells reaches the “Voltage to reset the “Ready to charge"” level and 2) the "Delay before recharging" time has passed since the opening of the allow charging contactor.
446		-
447	447	=== Discharge ===
448	448
449	449	The device controls the discharging contactor to connect battery to the load.
...	...	@@ -490,7 +490,10 @@
490	490	* if there is signal “Discharge request”, the charging contactor is open and there are no errors (see the list above), then through the delay time T,,on,, the discharging contactor closes;
491	491	* If the signal “Discharge request” disappears or errors occur (see the list above), then after the delay time T,,off,, the discharging contactor opens.
492	492
493		-Note – In case of errors in the system operation, the opening of the discharging contactor is performed either immediately or with a delay T,,off,, (depends on the settings described below).
	503	+(% class="box infomessage" %)
	504	+(((
	505	+**Note:** in case of errors in the system operation, **discharging **contactor opens either immediately or with a delay T,,off,, (depends on the settings described below).
	506	+)))
494	494
495	495	The device supports controlling the precharging contactor. The duration of switching on the precharging contactor before closing the discharging (load) contactor is adjusted.
496	496
...	...	@@ -515,8 +515,6 @@
515	515	* Precharge time – a duration of closing the precharge contactor before closing the discharging contactor, millisecond;
516	516	* Check voltages before and after contactors to finish precharging – a flag to check the voltages before and after contactors to ensure that precharge process has finished and it is allowed to close the discharging contactor;
517	517	* Minimum voltage difference to finish precharging – minimal voltage difference before and after contactors at which precharge process is meant to be finished, V;
518		-* Voltage to clear the “Ready to discharge” – a threshold voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
519		-* Voltage to reset the “Ready to discharge” – a tolerant voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
520	520
521	521	=== Charge/Discharge ===
522	522

1735063563460-549.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+59.6 KB

Content