Skip to Content
Last modified by Admin on 2026/04/02 13:49
From version 89.8
edited by Admin
on 2026/03/25 16:56
Change comment: There is no comment for this version
To version 89.7
edited by Admin
on 2026/03/25 16:55
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -138,9 +138,9 @@
138 138  [[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
139 139  
140 140  |**Pin**|**Name**|**Description**
141 -|**1**|**LOGIC_A**|RS-485 line A for communication with BMS Logic
141 +|**1**|**RS_LOGIC_A**|RS-485 line A for communication with BMS Logic
142 142  |**2**|**LOGIC_B**|RS-485 line B for communication with BMS Logic
143 -|**3**|**LOGIC_5V**|Supply voltage for BMS Logic
143 +|**3**|**+5V**|Supply voltage for BMS Logic
144 144  |**4**|**GND**|Ground
145 145  
146 146  === X12 – header for CAN2 interface ===
... ... @@ -147,7 +147,7 @@
147 147  
148 148  Receptacle Housing: Molex 430250400. Terminals: Molex 43030
149 149  
150 -[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]By defaul
150 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
151 151  
152 152  |**Pin**|**Name**|**Description**
153 153  |**1**|**CAN2_H**|RS-485 line A for communication with BMS Logic
... ... @@ -172,7 +172,7 @@
172 172  === J1 – jumper for switching internal CAN bus terminal resistor ===
173 173  
174 174  
175 -[[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]To connect a terminal resistor between the **CAN2_H **and **CAN2_L **lines, install a jumper. The jumper is installed according to the table:
175 +[[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]To connect a terminal resistor between the **CAN_INT_H **and **CAN_INT_L **lines, install a jumper. The jumper is installed according to the table:
176 176  
177 177  |**Pin**|**Name**|**Description**
178 178  |**1-2**|**120 Ohm**|The 120 Ohm terminal resistor of the CAN1 bus is connected
... ... @@ -182,7 +182,7 @@
182 182  
183 183  [[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]
184 184  
185 -To connect a terminal resistor between the **RS485_1_A **and **RS485_1_B **lines, install a jumper. The jumper is installed according to the table:
185 +To connect a terminal resistor between the **RS_EXT_A **and **RS_EXT_B **lines, install a jumper. The jumper is installed according to the table:
186 186  
187 187  |**Pin**|**Name**|**Description**
188 188  |**1-2**|**120 Ohm**|The 120 Ohm terminal resistor of the RS-485-1 bus is connected
... ... @@ -191,7 +191,7 @@
191 191  === J3 – jumper for switching external CAN bus terminal resistor ===
192 192  
193 193  
194 -[[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]To connect a terminal resistor between the **CAN1_H **and **CAN1_L **lines, install a jumper. The jumper is installed according to the table:
194 +[[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]To connect a terminal resistor between the **CAN_EXT_H** and **CAN_EXT_L** lines, install a jumper. The jumper is installed according to the table:
195 195  
196 196  |**Pin**|**Name**|**Description**
197 197  |**1-2**|**120 Ohm**|The 120 Ohm terminal resistor of the CAN1 bus is connected