Skip to Content
Last modified by Admin on 2026/04/02 13:49
From version 87.3
edited by Admin
on 2026/03/25 16:41
Change comment: There is no comment for this version
To version 89.5
edited by Admin
on 2026/03/25 16:52
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -128,71 +128,58 @@
128 128  
129 129  |**Pin**|**Name**|**Description**
130 130  |**1, 2**|**GND**|Ground
131 -|**3**|**T_SENS1**|Ground
132 -|**4**|**T_SENS2**|Current sensor 2 output
131 +|**3**|**T_SENS1**|Temperature sensor 1 output
132 +|**4**|**T_SENS2**|Temperature sensor 2 output
133 133  
134 -=== X11 – header for high-voltage bus before contactors (plus) ===
134 +=== X11 – (% style="color:inherit; font-family:inherit; font-size:max(18px, min(20px, 14.4444px + 0.462963vw))" %)header for BMS Logic(%%) ===
135 135  
136 -Receptacle Housing: Molex 436450200. Terminals: Molex 43030
136 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
137 137  
138 -[[image:1733316780753-798.png||data-xwiki-image-style-alignment="center" height="60" width="91"]]
138 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
139 139  
140 140  |**Pin**|**Name**|**Description**
141 -|**1**|**IN1+**|Plus of the high-voltage bus (before contactors)
142 -|**2**|**IN1+**|Plus of the high-voltage bus (before contactors)
141 +|**1**|**RS_LOGIC_A**|RS-485 line A for communication with BMS Logic
142 +|**2**|**RS_LOGIC_B**|RS-485 line B for communication with BMS Logic
143 +|**3**|**+5V**|Supply voltage for BMS Logic
144 +|**4**|**GND**|Ground
143 143  
144 -(% class="box warningmessage" %)
145 -(((
146 -The connected voltage must not exceed 1000V.
147 -)))
146 +=== X12 – header for internal CAN2 interface ===
148 148  
149 -=== X12 – header for high-voltage bus before contactors (minus) ===
148 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
150 150  
151 -Receptacle Housing: Molex 436450200. Terminals: Molex 43030
150 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
152 152  
153 -[[image:1733316843397-336.png||data-xwiki-image-style-alignment="center" height="53" width="79"]]
154 -
155 155  |**Pin**|**Name**|**Description**
156 -|**1**|**IN1-**|Minus of the high-voltage bus (before contactors)
157 -|**2**|**IN1-**|Minus of the high-voltage bus (before contactors)
153 +|**1**|**CAN_INT_H**|RS-485 line A for communication with BMS Logic
154 +|**2**|**CAN_INT_L**|CAN L line for communication with external equipment
155 +|**3**|**–**|–
156 +|**4**|**GND**|Ground
158 158  
159 -(% class="box warningmessage" %)
160 -(((
161 -The connected voltage must not exceed 1000V.
162 -)))
158 +=== X13 – header for CAN1 and RS-485 interfaces ===
163 163  
164 -=== X13 – header for high-voltage bus after contactors (plus) ===
160 +Receptacle Housing: Molex 430250600. Terminals: Molex 43030
165 165  
166 -Receptacle Housing: Molex 436450200. Terminals: Molex 43030
162 +[[image:https://docs.movicomelectric.com/bin/download/Battery%20management%20systems/BMS%20Main%202.1/2.%20Installation%20and%20connection/WebHome/1731517180930-597.png?width=113&height=81&rev=1.1||alt="1731517180930-597.png" data-xwiki-image-style-alignment="center" height="81" width="113"]]
167 167  
168 -[[image:1733316780753-798.png||data-xwiki-image-style-alignment="center" height="60" width="91"]]
169 -
170 170  |**Pin**|**Name**|**Description**
171 -|**1**|**IN2+**|Plus of the high-voltage bus (after contactors)
172 -|**2**|**IN2+**|Plus of the high-voltage bus (after contactors)
165 +|**1**|**RS_EXT_A**|RS-485 line A for communication with external equipment
166 +|**2**|**CAN_EXT_H**|CAN H line for communication with external equipment
167 +|**3**|**+5V**|Supply voltage 5V for external devices, max 200 mA
168 +|**4**|**RS_EXT_B**|RS-485 line B for communication with external equipment
169 +|**5**|**CAN_EXT_L**|CAN L line for communication with external equipment
170 +|**6**|**GND**|Ground
173 173  
174 -(% class="box warningmessage" %)
175 -(((
176 -The connected voltage must not exceed 1000V.
177 -)))
172 +=== J1 – jumper for switching CAN2 bus terminal resistor ===
178 178  
179 -=== X14 – header for high-voltage bus after contactors (minus) ===
180 180  
181 -Receptacle Housing: Molex 436450200. Terminals: Molex 43030
175 +[[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]To connect a terminal resistor between the **CAN_INT_H **and **CAN_L** lines, install a jumper. The jumper is installed according to the table:
182 182  
183 -[[image:1733316843397-336.png||data-xwiki-image-style-alignment="center" height="53" width="79"]]
184 -
185 185  |**Pin**|**Name**|**Description**
186 -|**1**|**IN2-**|Minus of the high-voltage bus (after contactors)
187 -|**2**|**IN2-**|Minus of the high-voltage bus (after contactors)
178 +|**1-2**|**120 Ohm**|The 120 Ohm terminal resistor of the CAN1 bus is connected
179 +|**2-3**|**-**|The 120 Ohm terminal resistor of the CAN1 bus is disconnected
188 188  
189 -(% class="box warningmessage" %)
190 -(((
191 -The connected voltage must not exceed 1000V.
192 -)))
181 +=== J2 – jumper for switching RS-485 bus terminal resistor ===
193 193  
194 -=== J1 – jumper for switching RS-485-1 bus terminal resistor ===
195 -
196 196  [[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]
197 197  
198 198  To connect a terminal resistor between the **RS485_1_A** and **RS485_1_B** lines, install a jumper. The jumper is installed according to the table:
... ... @@ -201,10 +201,10 @@
201 201  |**1-2**|**120 Ohm**|The 120 Ohm terminal resistor of the RS-485-1 bus is connected
202 202  |**2-3**|**-**|The 120 Ohm terminal resistor of the RS-485-1 bus is disconnected
203 203  
204 -=== J2 – jumper for switching CAN1 bus terminal resistor ===
191 +=== J3 – jumper for switching CAN1 bus terminal resistor ===
205 205  
206 206  
207 -[[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]To connect a terminal resistor between the **CAN1_H** and **CAN1_L** lines, install a jumper. The jumper is installed according to the table:
194 +[[image:1733316982359-759.png||data-xwiki-image-style-alignment="center" height="77" width="148"]]To connect a terminal resistor between the **CAN_EXT_H** and **CAN_EXT_L** lines, install a jumper. The jumper is installed according to the table:
208 208  
209 209  |**Pin**|**Name**|**Description**
210 210  |**1-2**|**120 Ohm**|The 120 Ohm terminal resistor of the CAN1 bus is connected