Skip to Content

Changes for page 4. Firmware update

Last modified by Admin on 2025/03/03 13:18
From version 8.1
edited by Admin
on 2024/12/02 16:01
Change comment: There is no comment for this version
To version 18.2
edited by Admin
on 2025/03/03 13:14
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -BMS Main 2.1 firmware update
1 +4. Firmware update
Parent
... ... @@ -1,1 +1,1 @@
1 -drafts.WebHome
1 +Battery management systems.BMS Main 2\.1.WebHome
Content
... ... @@ -1,19 +1,24 @@
1 -== 1. Introduction ==
1 +(% data-numbered-headings-start="4" style="--numbered-headings-start: 3;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 += Firmware update =
2 2  
4 +== Introduction ==
5 +
3 3  This document describes the steps for updating the BMS Main 2.x firmware.
4 4  
5 5  Updating the BMS Main 2.x firmware can be done in the following ways:
6 6  
7 -* using ElectricDeviceMonitor via Ethernet, CAN or RS-485 bus;
8 -* using the device web interface via Ethernet or Wi-Fi.
10 +* via ElectricDeviceMonitor by Ethernet, CAN or RS-485 bus;
11 +* via web interface by Ethernet or Wi-Fi.
9 9  
10 -== 2. Updating via ElectricDeviceMonitor ==
13 +== Updating via ElectricDeviceMonitor ==
11 11  
12 12  The following hardware and software are required:
13 13  
14 14  * ElectricDeviceMonitor application for Windows OS which is used for configuring the BMS Main 2.x.
18 +*
15 15  * USB/CAN adapter (for updating via CAN bus).
16 16  * USB/RS-485 adapter (for updating via RS-485 bus).
21 +* SD-card installed on BMS Main 2.1 for update via configuration interface;
17 17  * Firmware file in .srec (Motorola S-record) format.
18 18  
19 19  Firmware updating includes two steps:
... ... @@ -21,7 +21,7 @@
21 21  * starting the bootloader;
22 22  * uploading the firmware file to the BMS Main 2.x flash memory.
23 23  
24 -==== 2.1. Start the device bootloader. ====
29 +=== Start the device bootloader ===
25 25  
26 26  * **via Web Interface**: go to the "Service → Device" section and click on the link "Reset device and start loader":
27 27  
... ... @@ -29,7 +29,7 @@
29 29  
30 30  * **via ElectricDeviceMonitor**: connect to the BMS Main 2.x device using a USB-CAN adapter and the ElectricDeviceMonitor program. Next, in the monitor program, go to the "Service → Commands" section and click on the "Reset device and start loader" button:
31 31  
32 -[[image:1732876996076-348.png||data-xwiki-image-style-alignment="center" height="336" width="482"]]
37 +[[image:1732876996076-348.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="336" width="482"]]
33 33  
34 34  * **via SW1 button**: hold the SW1 button on the device for 1 second. After the indication LEDs go out, release the button. A restart will be performed, and the device will enter bootloader mode.
35 35  
... ... @@ -40,15 +40,15 @@
40 40  The bootloader will be active for 45 seconds. After this time, control will be transferred again to the main firmware.
41 41  )))
42 42  
43 -==== 2.2. Upload the firmware. ====
48 +=== Upload the firmware ===
44 44  
45 -Launch the ElectricDeviceMonitor’s Updater module:
50 +~1. Launch the ElectricDeviceMonitor’s Updater module:
46 46  
47 47  [[image:1732876973941-940.png||data-xwiki-image-style-alignment="center"]]
48 48  
49 49  [[image:1732876980743-472.png||data-xwiki-image-style-alignment="center"]]
50 50  
51 -From the drop-down menu of the Updater window, select the method of connecting to the BMS Main 2.x device and configure the connection parameters (the "Settings..." button).
56 +2. From the drop-down menu of the Updater window, select the method of connecting to the BMS Main 2.x device and configure the connection parameters (the "Settings..." button).
52 52  
53 53  * **Ethernet connection**: select the connection method "TCP transport", click the "Settings..." button and, in the window that appears, specify the device's IP address and bootloader port number:
54 54  
... ... @@ -58,15 +58,15 @@
58 58  
59 59  [[image:1732877027638-368.png||data-xwiki-image-style-alignment="center"]]
60 60  
61 -* **RS-485 connection**: select the connection method “Serial port transport”, click the “Settings...” button. In the window that appears, select the COM port through which the PC connects to the device, and specify the baud rate for the COM port:
66 +* **RS-485 connection**: select the connection method “Serial port transport”, click the “Settings...” button. In the window that appears, select the COM port through which the PC connects to the device, and specify the baud rate (set up in BMS settings):
62 62  
63 -[[image:1732877039628-104.png||data-xwiki-image-style-alignment="center"]]
68 +[[image:1741006734310-418.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
64 64  
65 -Click the "Browse..." button and select the *.srec file with the main firmware.
70 +3. Click the "Browse..." button and select the *.srec file with the BMS Main 2.1 firmware.
66 66  
67 -Click the “Update” button **while the device is in bootloader mode**. The process of loading the new firmware into the device memory will begin.
72 +4. Click the “Update” button **while the device is in bootloader mode**. The process of loading the new firmware into the device memory will begin.
68 68  
69 -== 3. Updating via WEB interface ==
74 +== Updating via WEB interface ==
70 70  
71 71  (% class="box warningmessage" %)
72 72  (((
1741006696516-394.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +6.9 KB
Content
1741006734310-418.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +6.9 KB
Content