Changes for page 4. Firmware update

Summary

• Page properties (3 modified, 0 added, 0 removed)

Details

Page properties

Title

...	...	@@ -1,1 +1,1 @@
1		-4. Firmware update
	1	+BMS Main 2.1 firmware update

Parent

...	...	@@ -1,1 +1,1 @@
1		-Battery management systems.BMS Main 2\.1.WebHome
	1	+drafts.WebHome

Content

...	...	@@ -1,8 +1,5 @@
1		-(% data-numbered-headings-start="4" style="--numbered-headings-start: 3;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2		-= Firmware update =
	1	+== 1. Introduction ==
3	3
4		-== Introduction ==
5		-
6	6	This document describes the steps for updating the BMS Main 2.x firmware.
7	7
8	8	Updating the BMS Main 2.x firmware can be done in the following ways:
...	...	@@ -10,7 +10,7 @@
10	10	* using ElectricDeviceMonitor via Ethernet, CAN or RS-485 bus;
11	11	* using the device web interface via Ethernet or Wi-Fi.
12	12
13		-== Updating via ElectricDeviceMonitor ==
	10	+== 2. Updating via ElectricDeviceMonitor ==
14	14
15	15	The following hardware and software are required:
16	16
...	...	@@ -24,7 +24,7 @@
24	24	* starting the bootloader;
25	25	* uploading the firmware file to the BMS Main 2.x flash memory.
26	26
27		-=== Start the device bootloader ===
	24	+==== 2.1. Start the device bootloader. ====
28	28
29	29	* **via Web Interface**: go to the "Service → Device" section and click on the link "Reset device and start loader":
30	30
...	...	@@ -32,7 +32,7 @@
32	32
33	33	* **via ElectricDeviceMonitor**: connect to the BMS Main 2.x device using a USB-CAN adapter and the ElectricDeviceMonitor program. Next, in the monitor program, go to the "Service → Commands" section and click on the "Reset device and start loader" button:
34	34
35		-[[image:1732876996076-348.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="336" width="482"]]
	32	+[[image:1732876996076-348.png||data-xwiki-image-style-alignment="center" height="336" width="482"]]
36	36
37	37	* **via SW1 button**: hold the SW1 button on the device for 1 second. After the indication LEDs go out, release the button. A restart will be performed, and the device will enter bootloader mode.
38	38
...	...	@@ -43,15 +43,15 @@
43	43	The bootloader will be active for 45 seconds. After this time, control will be transferred again to the main firmware.
44	44	)))
45	45
46		-=== Upload the firmware ===
	43	+==== 2.2. Upload the firmware. ====
47	47
48		-~1. Launch the ElectricDeviceMonitor’s Updater module:
	45	+Launch the ElectricDeviceMonitor’s Updater module:
49	49
50	50	[[image:1732876973941-940.png||data-xwiki-image-style-alignment="center"]]
51	51
52	52	[[image:1732876980743-472.png||data-xwiki-image-style-alignment="center"]]
53	53
54		-2. From the drop-down menu of the Updater window, select the method of connecting to the BMS Main 2.x device and configure the connection parameters (the "Settings..." button).
	51	+From the drop-down menu of the Updater window, select the method of connecting to the BMS Main 2.x device and configure the connection parameters (the "Settings..." button).
55	55
56	56	* **Ethernet connection**: select the connection method "TCP transport", click the "Settings..." button and, in the window that appears, specify the device's IP address and bootloader port number:
57	57
...	...	@@ -65,11 +65,11 @@
65	65
66	66	[[image:1732877039628-104.png||data-xwiki-image-style-alignment="center"]]
67	67
68		-3. Click the "Browse..." button and select the *.srec file with the BMS Main 2.1 firmware.
	65	+Click the "Browse..." button and select the *.srec file with the main firmware.
69	69
70		-4. Click the “Update” button **while the device is in bootloader mode**. The process of loading the new firmware into the device memory will begin.
	67	+Click the “Update” button **while the device is in bootloader mode**. The process of loading the new firmware into the device memory will begin.
71	71
72		-== Updating via WEB interface ==
	69	+== 3. Updating via WEB interface ==
73	73
74	74	(% class="box warningmessage" %)
75	75	(((