Skip to Content

Changes for page 3.6 Battery protection

Last modified by Admin on 2025/04/09 12:25
From version 46.2
edited by Admin
on 2025/04/02 10:07
Change comment: There is no comment for this version
To version 41.1
edited by Admin
on 2025/01/10 09:49
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -10,7 +10,7 @@
10 10  
11 11  To change the current protection of the battery, select the menu "Protections → Overcurrent protection":
12 12  
13 -[[image:1743588404359-971.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="325" width="450"]]
13 +[[image:1732211959984-118.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="266" width="386"]]
14 14  
15 15   In this section:
16 16  
... ... @@ -21,7 +21,6 @@
21 21  * Tolerant discharging current, А;
22 22  * Delay before setting the error, second;
23 23  * Delay before clearing the error, second;
24 -* Use other delays if the battery is discharging – a flag to enable alternative timings for
25 25  * Lock the error until the device is reset – a flag to block the error until the board is restarted.
26 26  
27 27  As a result of operation of the current protection, the "Overcurrent" error is generated.
... ... @@ -47,7 +47,7 @@
47 47  
48 48  To change the battery protection parameters from low voltage on the cells, select the menu "Protections → Undervoltage protection":
49 49  
50 -[[image:1739960999969-617.png||alt="1739961158202-478.png" data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="228" width="351"]]
49 +[[image:1732212212350-294.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="207" width="359"]]
51 51  
52 52   In this section:
53 53  
... ... @@ -54,7 +54,6 @@
54 54  * Enable – a flag to enable the protection;
55 55  * Minimum cell voltage, V;
56 56  * Tolerant cell voltage, V;
57 -* Check the open circuit voltage instead of the actual voltage – a flag to enable U,,ocv,, correction depending on cell current and resistance;
58 58  * Delay before setting the error, second;
59 59  * Delay before clearing the error, second;
60 60  * Lock the error until the device is reset.
... ... @@ -78,7 +78,7 @@
78 78  
79 79  To change the battery protection parameters from high voltage on the cells, select the menu "Protections → Overvoltage protection":
80 80  
81 -[[image:1739961158202-478.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="237" width="353"]]
79 +[[image:1732212357972-295.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="218" width="338"]]
82 82  
83 83  In this section:
84 84  
... ... @@ -85,7 +85,6 @@
85 85  * Enable – a flag to enable the protection;
86 86  * Maximum cell voltage, V;
87 87  * Tolerant cell voltage, V;
88 -* Check the open circuit voltage instead of the actual voltage – a flag to enable U,,ocv,, correction depending on cell current and resistance;
89 89  * Delay before setting the error, second;
90 90  * Delay before clearing the error, second;
91 91  * Switch off the discharging relay on error – a flag to open the discharging relay when the "Overvoltage" error is generated;
... ... @@ -629,7 +629,7 @@
629 629  
630 630  * Enable – a flag to enable the protection;
631 631  * Logic count – a number of BMS Logic boards connected to the BMS Main 2.x;
632 -* Fast scanning – a flag to scan BMS Logic boards fast (boards with addresses from 1 to “Logic count” are scanned; this mode reduces BMS system startup time);
629 +* Fast scan – a flag to scan BMS Logic boards fast (boards with addresses from 1 to “Logic count” are scanned; this mode reduces BMS system startup time);
633 633  * Lock the error until the device is reset.
634 634  
635 635  As a result of the operation of the protection from the mismatch of the number of BMS Logic boards, the "Logic count error" is generated.
... ... @@ -681,10 +681,6 @@
681 681  In this section:
682 682  
683 683  * Enable – a flag to enable the protection;
684 -* Algorithm:
685 -** Always;
686 -** On charging;
687 -** Except charging;
688 688  * Delay before setting the error, second;
689 689  * Delay before clearing the error, second;
690 690  * Lock the error until the device is reset.
1739960999969-617.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -19.8 KB
Content
1739961158202-478.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -22.3 KB
Content
1743588404359-971.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -29.7 KB
Content