Skip to Content

Changes for page 3.6 Battery protection

Last modified by Admin on 2026/04/24 10:30
From version 43.1
edited by Admin
on 2025/02/19 10:30
Change comment: Загрузить новое вложение 1739960999969-617.png
To version 49.6
edited by Admin
on 2026/04/24 10:29
Change comment: Renamed back-links.

Summary

Details

Page properties
Content
... ... @@ -10,7 +10,7 @@
10 10  
11 11  To change the current protection of the battery, select the menu "Protections → Overcurrent protection":
12 12  
13 -[[image:1732211959984-118.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="266" width="386"]]
13 +[[image:1743588404359-971.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="325" width="450"]]
14 14  
15 15   In this section:
16 16  
... ... @@ -21,6 +21,9 @@
21 21  * Tolerant discharging current, А;
22 22  * Delay before setting the error, second;
23 23  * Delay before clearing the error, second;
24 +* Use other delays if the battery is discharging – a flag to enable alternative timings for battery discharging;
25 +* Discharging: Delay before setting the error, second;
26 +* Discharging: Delay before clearing the error, second;
24 24  * Lock the error until the device is reset – a flag to block the error until the board is restarted.
25 25  
26 26  As a result of operation of the current protection, the "Overcurrent" error is generated.
... ... @@ -46,7 +46,7 @@
46 46  
47 47  To change the battery protection parameters from low voltage on the cells, select the menu "Protections → Undervoltage protection":
48 48  
49 -[[image:1732212212350-294.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="207" width="359"]]
52 +[[image:1739960999969-617.png||alt="1739961158202-478.png" data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="228" width="351"]]
50 50  
51 51   In this section:
52 52  
... ... @@ -53,6 +53,7 @@
53 53  * Enable – a flag to enable the protection;
54 54  * Minimum cell voltage, V;
55 55  * Tolerant cell voltage, V;
59 +* Check the open circuit voltage instead of the actual voltage – a flag to use the U,,ocv,, (corrected due to current and cell resistance) cell voltage;
56 56  * Delay before setting the error, second;
57 57  * Delay before clearing the error, second;
58 58  * Lock the error until the device is reset.
... ... @@ -76,7 +76,7 @@
76 76  
77 77  To change the battery protection parameters from high voltage on the cells, select the menu "Protections → Overvoltage protection":
78 78  
79 -[[image:1732212357972-295.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="218" width="338"]]
83 +[[image:1739961158202-478.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="237" width="353"]]
80 80  
81 81  In this section:
82 82  
... ... @@ -83,6 +83,7 @@
83 83  * Enable – a flag to enable the protection;
84 84  * Maximum cell voltage, V;
85 85  * Tolerant cell voltage, V;
90 +* Check the open circuit voltage instead of the actual voltage – a flag to use the U,,ocv,, (corrected due to current and cell resistance) cell voltage;
86 86  * Delay before setting the error, second;
87 87  * Delay before clearing the error, second;
88 88  * Switch off the discharging relay on error – a flag to open the discharging relay when the "Overvoltage" error is generated;
... ... @@ -423,7 +423,7 @@
423 423  
424 424  === Contactor feedback check ===
425 425  
426 -The BMS Main 2.x can receive feedback signals from contactors and detect discrepancy between the control value and the feedback signal. To enable specific contactor protection, one of the discrete input must be set as corresponding contactor feedback signal (see [[Input and output signals>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.3 Input and output signals.WebHome]]).
431 +The BMS Main 2.x can receive feedback signals from contactors and detect discrepancy between the control value and the feedback signal. To enable specific contactor protection, one of the discrete input must be set as corresponding contactor feedback signal (see [[Input and output signals>>doc:Battery management systems.BMS Main 2\.1 (End-of-Life).3\. Configuration.3\.3 Input and output signals.WebHome]]).
427 427  
428 428  To change the contactor feedback check parameters, select the menu "Protections → Contactor feedback check":
429 429  
1739961158202-478.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +22.3 KB
Content
1743588404359-971.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +29.7 KB
Content
1743588519424-405.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +29.7 KB
Content