Changes for page 3.6 Battery protection
Last modified by Admin on 2025/04/09 12:25
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -706,89 +706,17 @@ 706 706 707 707 * the battery SOC is greater than the “Tolerant SOC” during the “Delay before clearing the signal” time. 708 708 709 -The "Low SOC signal" is //indicative //and can be linked to any discrete output of the board. 709 +(% class="box infomessage" %) 710 +((( 711 +The "Low SOC signal" is indicative and can be linked to any discrete output of the board. 712 +))) 710 710 711 711 == 3.6.27 High charging current signal == 712 712 713 -To change the parameters of the generation high-current signal, select the menu "Protections → High charging current signal": 714 - 715 - 716 -In this section: 717 - 718 -* Enable – a flag to enable signal generation; 719 -* Maximum charging current, А; 720 -* Tolerant charging current, А; 721 -* Delay before setting the signal, second; 722 -* Delay before clearing the signal, second; 723 -* Lock the signal until the device is reset. 724 - 725 -Signal generation conditions: 726 - 727 -* the measured current is greater than the “Maximum charging current” value during the “Delay before setting the signal” time. 728 - 729 -Conditions for clearing the signal: 730 - 731 -* the measured current is less than the “Tolerant charging current” value during the “Delay before clearing the signal” time. 732 - 733 -The "High charging current" signal is //indicative //and can be linked to any discrete output of the board. 734 - 735 735 == 3.6.28 Heater control == 736 736 737 -To change the parameters of the heater control algorithm, select the menu "Protections → Heater control": 738 - 739 - 740 -In this section: 741 - 742 -* Enable – a flag to enable heater control; 743 -* Minimum cell temperature, °C; 744 -* Tolerant cell temperature, °C; 745 -* Delay before setting the signal, second; 746 -* Delay before clearing the signal, second; 747 -* Lock the signal until the device is reset; 748 -* Switch off the heater relay on errors (Undervoltage, Overcurrent, High temperature, Short circuit or Critical error). 749 - 750 -As a result of operating the heating algorithm, the “Heater” signal is generated. 751 - 752 -Conditions of signal generation: 753 - 754 -* The minimum temperature among all cells of the battery is less than the “Minimum cell temperature” value during the “Delay before setting the signal” time. 755 - 756 -Conditions for clearing the signal: 757 - 758 -* the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before clearing the signal” time. 759 - 760 -(% class="box infomessage" %) 761 -((( 762 -If there is the "Heater" signal, the heater relay closes and/or a signal is output to the corresponded digital output. 763 -))) 764 - 765 765 == 3.6.29 Heater (AUX) control == 766 766 767 -To change the parameters of the heater control algorithm, select the menu "Protections → Heater (AUX) control": 768 - 769 - 770 -In this section: 771 - 772 -* Enable – a flag to enable heater control; 773 -* Minimum cell temperature, °C; 774 -* Tolerant cell temperature, °C; 775 -* Delay before setting the signal, second; 776 -* Delay before clearing the signal, second; 777 -* Lock the signal until the device is reset; 778 -* Switch off the heater relay on errors (Undervoltage, Overcurrent, High temperature, Short circuit or Critical error). 779 - 780 -As a result of operating the heating algorithm, the “Heater (AUX)” signal is generated. 781 - 782 -Conditions of signal generation: 783 - 784 -* The minimum temperature among all cells of the battery is less than the “Minimum cell temperature” value during the “Delay before setting the signal” time. 785 - 786 -Conditions for clearing the signal: 787 - 788 -* the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before clearing the signal” time. 789 - 790 -If there is the "Heater" signal, the heater relay closes and/or a signal is output to the corresponded digital output. 791 - 792 792 == 3.6.30 Cooler control == 793 793 794 794 == 3.6.31 Fault simulation ==