Changes for page 3.6 Battery protection

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -616,101 +616,14 @@
616	616	To change the parameters of the watchdog protection, select the menu "Protections → WDT protection":
617	617
618	618
619		-In this section:
620		-
621		-* Enable – a flag to enable the protection;
622		-* Delay before clearing the error, second;
623		-* Lock the error until the device is reset.
624		-
625		-Conditions for removing the error:
626		-
627		-* the “Delay before clearing the error” time has passed from the board startup.
628		-
629		-(% class="box warningmessage" %)
630		-(((
631		-**If there is the "WDT reset" error, the “Critical error” is generated and all relays open.**
632		-)))
633		-
634	634	== 3.6.23 Insulation monitoring ==
635	635
636		-BMS Main 2.x can detect a signal from an external insulation monitoring device (such as Bender IR155) to monitor the insulation quality.
637		-
638		-To change the insulation monitoring parameters, select the menu "Protections → Insulation monitoring":
639		-
640		-
641		-In this section:
642		-
643		-* Enable – a flag to enable the protection;
644		-* Delay before setting the error, second;
645		-* Delay before clearing the error, second;
646		-* Lock the error until the device is reset.
647		-
648		-Error is set if corresponding discrete input is set up and it received logical zero.
649		-
650	650	== 3.6.24 Critical error parameters ==
651	651
652		-To change the critical error parameters, select the menu "Protections → Critical error parameters":
653		-
654		-
655		-In this section:
656		-
657		-* Enable – a flag to enable the protection;
658		-* Delay before setting the error, second;
659		-* Delay before clearing the error, second;
660		-* Lock the error until the device is reset.
661		-
662		-The critical error flag is generated if at least one of the following errors is generated during the “Delay before setting the error” time:
663		-
664		-* “Battery cover error”;
665		-* “Water”;
666		-* “Logic offline”;
667		-* “Cell count error”;
668		-* “Logic count error”;
669		-* “ADC error”;
670		-* “No temp. sensors”;
671		-* “Temp. sensor is shorted”;
672		-* “Current sensor error”;
673		-* “Shunt offline”;
674		-* “Shunt error”;
675		-* “Settings error”;
676		-* “WDT reset”.
677		-
678		-The “Critical error” is cleared if there are no errors from the list above during the “Delay before clearing the error” time.
679		-
680		-(% class="box warningmessage" %)
681		-(((
682		-**If there is the “Critical error”, all relays open.**
683		-)))
684		-
685	685	== 3.6.25 General error parameters ==
686	686
687	687	== 3.6.26 Low SOC signal ==
688	688
689		-To change the parameters of the generation a signal about low battery level, select the menu "Protections → Low SOC signal":
690		-
691		-
692		-In this section:
693		-
694		-* Enable – a flag to enable signal generation;
695		-* Minimum SOC, %;
696		-* Tolerant SOC, %;
697		-* Delay before setting the signal, second;
698		-* Delay before clearing the signal, second;
699		-* Lock the signal until the device is reset.
700		-
701		-Signal generation conditions:
702		-
703		-* the battery SOC is less than the “Minimum SOC” value during the “Delay before setting the signal” time.
704		-
705		-Conditions for clearing the signal:
706		-
707		-* the battery SOC is greater than the “Tolerant SOC” during the “Delay before clearing the signal” time.
708		-
709		-(% class="box infomessage" %)
710		-(((
711		-The "Low SOC signal" is indicative and can be linked to any discrete output of the board.
712		-)))
713		-
714	714	== 3.6.27 High charging current signal ==
715	715
716	716	== 3.6.28 Heater control ==