Changes for page 3.6 Battery protection

Last modified by Admin on 2025/04/09 12:25

From 4.21 to 4.22 From 19.1 to 19.2

From version 4.22

edited by Admin
on 2024/11/21 18:27

Change comment: There is no comment for this version

To version 19.1

edited by Admin
on 2024/11/21 18:41

Change comment: Uploaded new attachment "1732214501360-654.png", version {1}

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 15 added, 0 removed)

Details

Page properties

Content

@@ -70,7 +70,7 @@
  To change the battery protection parameters from high voltage on the cells, select the menu "Protections → Overvoltage protection":
--[[image:1732212357972-295.png]]
++[[Overvoltage protection settings>>image:1732212357972-295.png||data-xwiki-image-style-alignment="center" height="218" width="338"]]
  In this section:
@@ -103,6 +103,7 @@
  To change the battery protection parameters from low temperature, select the menu "Protections → Low temperature protection":
++[[Low temperature protection settings>>image:1732213953083-955.png||data-xwiki-image-style-alignment="center" height="237" width="338"]]
  In this section:
@@ -137,6 +137,7 @@
  To change the battery protection parameters from high temperature, select the menu "Protections → High temperature protection":
++[[High temperature protection settings>>image:1732213990755-759.png||data-xwiki-image-style-alignment="center" height="258" width="370"]]
  In this section:
@@ -169,6 +169,8 @@
  To change the protection parameters from opening the battery cover, select the menu "Protections → Battery cover protection":
++[[Battery cover protection settings>>image:1732214030014-281.png||data-xwiki-image-style-alignment="center" height="155" width="334"]]
++
  In this section:
  * Enable – a flag to enable the protection;
@@ -197,12 +197,13 @@
  To change the protection parameters of the battery from high humidity, select the menu "Protections → High humidity protection":
++[[High humidity protection settings>>image:1732214076060-358.png||data-xwiki-image-style-alignment="center" height="185" width="321"]]
  In this section:
  * Enable – a flag to enable the protection;
--* Maximum humidty, RH%;
--* Tolerant humidty, RH%;
++* Maximum humidity, RH%;
++* Tolerant humidity, RH%;
  * Delay before setting the error, second;
  * Delay before clearing the error, second;
  * Lock the error until the device is reset.
@@ -226,6 +226,7 @@
  To change the protection parameters of the battery from water, select the menu "Protections → Water protection":
++[[Water protection settings>>image:1732214111990-184.png||data-xwiki-image-style-alignment="center" height="199" width="340"]]
  In this section:
@@ -257,6 +257,7 @@
  To change the test parameters of the current sensor connection circuits, select the menu "Protections → Current sensor error":
++[[Current sensor error settings>>image:1732214146724-132.png||data-xwiki-image-style-alignment="center" height="438" width="365"]]
  In this section:
@@ -290,6 +290,7 @@
  To change the protection parameters from short circuit, select the menu "Protections → Short circuit protection":
++[[Short circuit protection settings>>image:1732214207026-822.png||data-xwiki-image-style-alignment="center" height="528" width="371"]]
  In this section:
@@ -323,6 +323,7 @@
  To change the overheating protection parameters of power contactors, select the menu "Protections → Contactor high temperature protection":
++[[Contactor high temperature protection settings>>image:1732214237851-405.png||data-xwiki-image-style-alignment="center" height="234" width="336"]]
  In this section:
@@ -356,6 +356,7 @@
  To change the parameters of the unallowable charging protection, select the menu "Protections → Unallowable charging protection":
++[[Unallowable charging protection settings>>image:1732214272022-547.png||data-xwiki-image-style-alignment="center" height="145" width="312"]]
  In this section:
@@ -385,6 +385,7 @@
  To change the protection parameters against sticking, select the menu "Protections → Stuck contactor protection":
++[[Stuck contactor protection settings>>image:1732214367207-318.png||data-xwiki-image-style-alignment="center" height="152" width="331"]]
  In this section:
@@ -405,6 +405,7 @@
  To change the contactor feedback check parameters, select the menu "Protections → Contactor feedback check":
++[[Contactor feedback check settings>>image:1732214400721-274.png||data-xwiki-image-style-alignment="center" height="150" width="323"]]
  In this section:
@@ -423,6 +423,7 @@
  To change the protection parameters against high frequency switching of the charging contactor, select the menu "Protections → Charging contactor cycles protection":
++[[image:1732214432750-543.png]]
  In this section:
@@ -706,17 +706,162 @@
  * the battery SOC is greater than the “Tolerant SOC” during the “Delay before clearing the signal” time.
--(% class="box infomessage" %)
--(((
--The "Low SOC signal" is indicative and can be linked to any discrete output of the board.
--)))
++The "Low SOC signal" is //indicative //and can be linked to any discrete output of the board.
  == 3.6.27 High charging current signal ==
++To change the parameters of the generation high-current signal, select the menu "Protections → High charging current signal":
++
++
++In this section:
++
++* Enable – a flag to enable signal generation;
++* Maximum charging current, А;
++* Tolerant charging current, А;
++* Delay before setting the signal, second;
++* Delay before clearing the signal, second;
++* Lock the signal until the device is reset.
++
++Signal generation conditions:
++
++* the measured current is greater than the “Maximum charging current” value during the “Delay before setting the signal” time.
++
++Conditions for clearing the signal:
++
++* the measured current is less than the “Tolerant charging current” value during the “Delay before clearing the signal” time.
++
++The "High charging current" signal is //indicative //and can be linked to any discrete output of the board.
++
  == 3.6.28 Heater control ==
++To change the parameters of the heater control algorithm, select the menu "Protections → Heater control":
++
++
++In this section:
++
++* Enable – a flag to enable heater control;
++* Minimum cell temperature, °C;
++* Tolerant cell temperature, °C;
++* Delay before setting the signal, second;
++* Delay before clearing the signal, second;
++* Lock the signal until the device is reset;
++* Switch off the heater relay on errors (Undervoltage, Overcurrent, High temperature, Short circuit or Critical error).
++
++As a result of operating the heating algorithm, the “Heater” signal is generated.
++
++Conditions of signal generation:
++
++* The minimum temperature among all cells of the battery is less than the “Minimum cell temperature” value during the “Delay before setting the signal” time.
++
++Conditions for clearing the signal:
++
++* the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before clearing the signal” time.
++
++(% class="box infomessage" %)
++(((
++If there is the "Heater" signal, the heater relay closes and/or a signal is output to the corresponded digital output.
++)))
++
  == 3.6.29 Heater (AUX) control ==
++To change the parameters of the auxiliary heater control algorithm, select the menu "Protections → Heater (AUX) control":
++
++
++In this section:
++
++* Enable – a flag to enable heater control;
++* Minimum cell temperature, °C;
++* Tolerant cell temperature, °C;
++* Delay before setting the signal, second;
++* Delay before clearing the signal, second;
++* Lock the signal until the device is reset;
++* Switch off the heater relay on errors (Undervoltage, Overcurrent, High temperature, Short circuit or Critical error).
++
++As a result of operating the heating algorithm, the “Heater (AUX)” signal is generated.
++
++Conditions of signal generation:
++
++* The minimum temperature among all cells of the battery is less than the “Minimum cell temperature” value during the “Delay before setting the signal” time.
++
++Conditions for clearing the signal:
++
++* the minimum temperature among all cells of the battery is greater than the “Tolerant cell temperature” value during the “Delay before clearing the signal” time.
++
++(% class="box infomessage" %)
++(((
++If there is the "Heater (AUX)" signal, the auxiliary heater relay closes and/or a signal is output to the corresponded digital output.
++)))
++
  == 3.6.30 Cooler control ==
++To change the parameters of the cooler control algorithm, select the menu "Protections → Cooler control":
++
++
++In this section:
++
++* Enable – a flag to enable cooler control;
++* Maximum cell temperature, °C;
++* Tolerant cell temperature, °C;
++* Delay before setting the signal, second;
++* Delay before clearing the signal, second;
++* Lock the signal until the device is reset;
++* Switch off the cooler relay on errors (Undervoltage, Overcurrent, Low temperature, Short circuit or Critical error).
++
++As a result of operating the cooling algorithm, the "Cooler" signal is generated.
++
++Conditions of signal generation:
++
++* the maximum temperature among all cells of the battery is greater than the “Maximum cell temperature” value during the “Delay before setting the signal” time.
++
++Conditions for clearing the signal:
++
++* the maximum temperature among all cells of the battery is less than the “Tolerant cell temperature” value during the “Delay before clearing the signal” time.
++
++(% class="box infomessage" %)
++(((
++If there is the "Cooler" signal, the cooler relay closes and/or a signal is output to the corresponded digital output.
++)))
++
  == 3.6.31 Fault simulation ==
++
++The board provides the ability to manually generate error flags bypassing the protection algorithms. This functionality is intended for commissioning.
++
++To simulate battery and BMS errors, select the menu "Protections → Fault simulation":
++
++
++In this section:
++
++* Overcurrent;
++* Undervoltage;
++* Overvoltage;
++* Low CH temperature;
++* Low DCH temperature;
++* High CH temperature;
++* High DCH temperature;
++* Battery cover error;
++* High humidity;
++* Water;
++* Current sensor error;
++* Short circuit;
++* Contactor high temperature;
++* Unallowable charging;
++* Stuck contactor;
++* CH contactor feedback error;
++* DCH contactor feedback error;
++* PCH contactor feedback error;
++* CH/DCH contactor feedback error;
++* Main contactor feedback error;
++* CH contactor cycles error;
++* DCH contactor cycles error;
++* Logic high temperature;
++* Logic offline;
++* Cell count error;
++* Logic count error;
++* Insulation error;
++* Critical error;
++* Low SOC;
++* High charging current;
++* Heater;
++* Cooler.
++
++To simulate errors, set the necessary flags and click on the "Save" button.

1732213953083-955.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+22.0 KB

Content

1732213990755-759.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+22.7 KB

Content

1732214030014-281.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+12.6 KB

Content

1732214076060-358.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+16.1 KB

Content

1732214111990-184.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+16.1 KB

Content

1732214146724-132.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+27.8 KB

Content

1732214183037-761.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+32.7 KB

Content

1732214207026-822.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+32.8 KB

Content

1732214237851-405.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+22.6 KB

Content

1732214272022-547.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+13.7 KB

Content

1732214367207-318.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+13.2 KB

Content

1732214400721-274.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+13.9 KB

Content

1732214432750-543.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+20.1 KB

Content

1732214468462-541.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+20.3 KB

Content

1732214501360-654.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.admin

Size

...	...	@@ -1,0 +1,1 @@
	1	+13.1 KB

Content

Changes for page 3.6 Battery protection

Summary

Details

Applications

Navigation

Table of Contents