Changes for page 3.6 Battery protection

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -534,21 +534,183 @@
534	534	To change the protection parameters from loss of communication with BMS Logic boards, select the menu "Protections → Logic offline protection":
535	535
536	536
	537	+In this section:
537	537
	539	+* Enable – a flag to enable the protection;
	540	+* Lock the error until the device is reset.
	541	+
	542	+As a result of the protection from loss of communication with BMS Logic boards, the "Logic offline" error is generated.
	543	+
	544	+Error generation conditions:
	545	+
	546	+* at least one of the connected BMS Logic boards does not respond to the commands of the BMS Main 2.x board for 10 seconds.
	547	+
	548	+Conditions for removing the error:
	549	+
	550	+* all connected BMS Logic boards respond to the commands of the BMS Main 2.x board.
	551	+
	552	+(% class="box warningmessage" %)
	553	+(((
	554	+**If there is the "Logic offline" error, the “Critical error” is generated and all relays open.**
	555	+)))
	556	+
538	538	== 3.6.20 Cell count protection ==
539	539
	559	+To change the protection parameters from the mismatch of the number of cells to the set value, select the menu "Protections → Cell count protection":
	560	+
	561	+
	562	+In this section:
	563	+
	564	+* Enable – a flag to enable the protection;
	565	+* Cell count – a number of cells connected to the BMS;
	566	+* Delay before setting the error, second;
	567	+* Delay before clearing the error, second;
	568	+* Lock the error until the device is reset.
	569	+
	570	+As a result of the operation of the protection from the mismatch of the number of cells, the "Cell count error" is generated.
	571	+
	572	+Error generation conditions:
	573	+
	574	+* the number of cells connected to the BMS is **not equal** to the “Cell count” value during the “Delay before setting the error” time.
	575	+
	576	+Conditions for removing the error:
	577	+
	578	+* the number of cells connected to the BMS is **equal** to the “Cell count” value during the “Delay before clearing the error” time.
	579	+
	580	+(% class="box warningmessage" %)
	581	+(((
	582	+**If there is the "Cell count error", the “Critical error” is generated and all relays open.**
	583	+)))
	584	+
540	540	== 3.6.21 Logic count protection ==
541	541
	587	+To change the protection parameters from the mismatch of the number of BMS Logic boards to the set value, select the menu "Protections → Logic count protection":
	588	+
	589	+
	590	+In this section:
	591	+
	592	+* Enable – a flag to enable the protection;
	593	+* Logic count – a number of BMS Logic boards connected to the BMS Main 2.x;
	594	+* Fast scan – a flag to scan BMS Logic boards fast (boards with addresses from 1 to “Logic count” are scanned; this mode reduces BMS system startup time);
	595	+* Lock the error until the device is reset.
	596	+
	597	+As a result of the operation of the protection from the mismatch of the number of BMS Logic boards, the "Logic count error" is generated.
	598	+
	599	+Error generation conditions:
	600	+
	601	+* the number of BMS Logic boards connected to the BMS Main 2.x is **not equal** to the “Logic count” value.
	602	+
	603	+Conditions for removing the error:
	604	+
	605	+* the number of BMS Logic boards connected to the BMS Main is **equal** to the “Logic count” value.
	606	+
	607	+(% class="box warningmessage" %)
	608	+(((
	609	+**If there is the "Logic count error", the “Critical error” is generated and all relays open.**
	610	+)))
	611	+
542	542	== 3.6.22 WDT protection ==
543	543
	614	+If the BMS firmware hangs, the watchdog timer resets the board. The BMS can detect that the board was reset and generates the “WDT reset” error.
	615	+
	616	+To change the parameters of the watchdog protection, select the menu "Protections → WDT protection":
	617	+
	618	+
	619	+In this section:
	620	+
	621	+* Enable – a flag to enable the protection;
	622	+* Delay before clearing the error, second;
	623	+* Lock the error until the device is reset.
	624	+
	625	+Conditions for removing the error:
	626	+
	627	+* the “Delay before clearing the error” time has passed from the board startup.
	628	+
	629	+(% class="box warningmessage" %)
	630	+(((
	631	+**If there is the "WDT reset" error, the “Critical error” is generated and all relays open.**
	632	+)))
	633	+
544	544	== 3.6.23 Insulation monitoring ==
545	545
	636	+BMS Main 2.x can detect a signal from an external insulation monitoring device (such as Bender IR155) to monitor the insulation quality.
	637	+
	638	+To change the insulation monitoring parameters, select the menu "Protections → Insulation monitoring":
	639	+
	640	+
	641	+In this section:
	642	+
	643	+* Enable – a flag to enable the protection;
	644	+* Delay before setting the error, second;
	645	+* Delay before clearing the error, second;
	646	+* Lock the error until the device is reset.
	647	+
	648	+Error is set if corresponding discrete input is set up and it received logical zero.
	649	+
546	546	== 3.6.24 Critical error parameters ==
547	547
	652	+To change the critical error parameters, select the menu "Protections → Critical error parameters":
	653	+
	654	+
	655	+In this section:
	656	+
	657	+* Enable – a flag to enable the protection;
	658	+* Delay before setting the error, second;
	659	+* Delay before clearing the error, second;
	660	+* Lock the error until the device is reset.
	661	+
	662	+The critical error flag is generated if at least one of the following errors is generated during the “Delay before setting the error” time:
	663	+
	664	+* “Battery cover error”;
	665	+* “Water”;
	666	+* “Logic offline”;
	667	+* “Cell count error”;
	668	+* “Logic count error”;
	669	+* “ADC error”;
	670	+* “No temp. sensors”;
	671	+* “Temp. sensor is shorted”;
	672	+* “Current sensor error”;
	673	+* “Shunt offline”;
	674	+* “Shunt error”;
	675	+* “Settings error”;
	676	+* “WDT reset”.
	677	+
	678	+The “Critical error” is cleared if there are no errors from the list above during the “Delay before clearing the error” time.
	679	+
	680	+(% class="box warningmessage" %)
	681	+(((
	682	+**If there is the “Critical error”, all relays open.**
	683	+)))
	684	+
548	548	== 3.6.25 General error parameters ==
549	549
550	550	== 3.6.26 Low SOC signal ==
551	551
	689	+To change the parameters of the generation a signal about low battery level, select the menu "Protections → Low SOC signal":
	690	+
	691	+
	692	+In this section:
	693	+
	694	+* Enable – a flag to enable signal generation;
	695	+* Minimum SOC, %;
	696	+* Tolerant SOC, %;
	697	+* Delay before setting the signal, second;
	698	+* Delay before clearing the signal, second;
	699	+* Lock the signal until the device is reset.
	700	+
	701	+Signal generation conditions:
	702	+
	703	+* the battery SOC is less than the “Minimum SOC” value during the “Delay before setting the signal” time.
	704	+
	705	+Conditions for clearing the signal:
	706	+
	707	+* the battery SOC is greater than the “Tolerant SOC” during the “Delay before clearing the signal” time.
	708	+
	709	+(% class="box infomessage" %)
	710	+(((
	711	+The "Low SOC signal" is indicative and can be linked to any discrete output of the board.
	712	+)))
	713	+
552	552	== 3.6.27 High charging current signal ==
553	553
554	554	== 3.6.28 Heater control ==