Skip to Content

Changes for page 3.6 Battery protection

Last modified by Admin on 2025/04/09 12:25
From version 4.13
edited by Admin
on 2024/11/21 18:17
Change comment: There is no comment for this version
To version 4.11
edited by Admin
on 2024/11/21 18:15
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -6,8 +6,9 @@
6 6  
7 7  [[Overcurrent protection settings>>image:1732211959984-118.png||data-xwiki-image-style-alignment="center" height="266" width="386"]]
8 8  
9 - In this section:
10 10  
10 +In this section:
11 +
11 11  * Enable – a flag to enable the protection;
12 12  * Maximum charging current, А;
13 13  * Tolerant charging current, А;
... ... @@ -31,7 +31,7 @@
31 31  
32 32  (% class="box infomessage" %)
33 33  (((
34 -If there is the "Overcurrent" error, the charging and discharging relay open.
35 +If there is the "Overcurrent" error, the charging relay and discharging relay open.
35 35  )))
36 36  
37 37  == 3.6.2 Undervoltage protection ==
... ... @@ -127,8 +127,7 @@
127 127  
128 128  (% class="box infomessage" %)
129 129  (((
130 -If there is the "Low CH temperature" error, the charging relay opens.
131 -If there is the "Low DCH temperature" error, the discharging relay opens.
131 +If there is the "Low CH temperature" error, the charging relay opens. If there is the "Low DCH temperature" error, the discharging relay opens.
132 132  )))
133 133  
134 134  == 3.6.5 High temperature protection ==
... ... @@ -137,7 +137,6 @@
137 137  
138 138  To change the battery protection parameters from high temperature, select the menu "Protections → High temperature protection":
139 139  
140 -
141 141  In this section:
142 142  
143 143  * Enable – a flag to enable the protection;
... ... @@ -167,58 +167,8 @@
167 167  
168 168  == 3.6.6 Battery cover protection ==
169 169  
170 -To change the protection parameters from opening the battery cover, select the menu "Protections → Battery cover protection":
169 +== 3.6.7 High humidity protection ==
171 171  
172 -In this section:
173 -
174 -* Enable – a flag to enable the protection;
175 -* Delay before setting the error, second;
176 -* Delay before clearing the error, second;
177 -* Lock the error until the device is reset.
178 -
179 -As a result of the operation of the protection against opening the battery cover, the “Battery cover error” is generated.
180 -
181 -Error generation conditions:
182 -
183 -* there is a signal from the battery cover during the “Delay before setting the error” time.
184 -
185 -Conditions for removing the error:
186 -
187 -* no signal from the battery cover during the “Delay before clearing the error” time.
188 -
189 -(% class="box warningmessage" %)
190 -(((
191 -**If there is the "Battery cover error", the “Critical error” is generated and all relays open.**
192 -)))
193 -
194 -== 3.6.7 High humidity protection ==
195 -
196 -The board can protect the battery from high humidity and water.
197 -
198 -To change the protection parameters of the battery from high humidity, select the menu "Protections → High humidity protection":
199 -
200 -In this section:
201 -
202 -* Enable – a flag to enable the protection;
203 -* Maximum humidty, RH%;
204 -* Tolerant humidty, RH%;
205 -* Delay before setting the error, second;
206 -* Delay before clearing the error, second;
207 -* Lock the error until the device is reset.
208 -
209 -As a result of the operation of the battery protection from high humidity, the "High humidity" error is generated.
210 -
211 -Error generation conditions:
212 -
213 -* the measured humidity is greater than “Maximum humidity” during the “Delay before setting the error” time.
214 -
215 -Conditions for removing the error:
216 -
217 -* the measured humidity is less than the “Tolerant humidity” during the “Delay before clearing the error” time.
218 -
219 -If there is the "High humidity" error, no action is taken. The error is indicative.
220 -
221 -
222 222  == 3.6.8  Water protection ==
223 223  
224 224  == 3.6.9 Current sensor error ==