Changes for page 3.6 Battery protection
Last modified by Admin on 2025/04/09 12:25
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -73,84 +73,4 @@ 73 73 74 74 [[image:1732212357972-295.png]] 75 75 76 -In this section: 77 - 78 -* Enable – a flag to enable the protection; 79 -* Maximum cell voltage, V; 80 -* Tolerant cell voltage, V; 81 -* Delay before setting the error, second; 82 -* Delay before clearing the error, second; 83 -* Switch off the discharging relay on error – a flag to open the discharging relay when the "Overvoltage" error is generated; 84 -* Lock the error until the device is reset. 85 - 86 -As a result of the operation of the battery protection from high voltage, the "Overvoltage" error is generated. 87 - 88 -Error generation conditions: 89 - 90 -* the maximum voltage among all cells of the battery is greater than the “Maximum cell voltage” value for the “Delay before setting the error” time. 91 - 92 -Conditions for removing the error: 93 - 94 -* the maximum voltage among all cells of the battery is less than the “Tolerant cell voltage” value for the “Delay before clearing the error” time. 95 - 96 -(% class="box infomessage" %) 97 -((( 98 -If there is the "Overvoltage" error, the charging relay and discharging relay opens (if the “Switch off the discharging relay on error” flag is set). 99 -))) 100 - 101 -== 3.6.4 Low temperature protection == 102 - 103 - 104 -== 3.6.5 High temperature protection == 105 - 106 -== 3.6.6 Battery cover protection == 107 - 108 -== 3.6.7 High humidity protection == 109 - 110 -== 3.6.8 Water protection == 111 - 112 -== 3.6.9 Current sensor error == 113 - 114 -== 3.6.10 Short circuit protection == 115 - 116 -== 3.6.11 Contactor high temperature protection == 117 - 118 -== 3.6.12 Unallowable charging protection == 119 - 120 -== 3.6.13 Stuck contactor protection == 121 - 122 -== 3.6.14 Contactor feedback check == 123 - 124 -== 3.6.15 Charging contactor cycles protection == 125 - 126 -== 3.6.16 Discharging contactor cycles protection == 127 - 128 -== 3.6.17 Temperature sensor error == 129 - 130 -== 3.6.18 Logic high temperature protection == 131 - 132 -== 3.6.19 Logic offline protection == 133 - 134 -== 3.6.20 Cell count protection == 135 - 136 -== 3.6.21 Logic count protection == 137 - 138 -== 3.6.22 WDT protection == 139 - 140 -== 3.6.23 Insulation monitoring == 141 - 142 -== 3.6.24 Critical error parameters == 143 - 144 -== 3.6.25 General error parameters == 145 - 146 -== 3.6.26 Low SOC signal == 147 - 148 -== 3.6.27 High charging current signal == 149 - 150 -== 3.6.28 Heater control == 151 - 152 -== 3.6.29 Heater (AUX) control == 153 - 154 -== 3.6.30 Cooler control == 155 - 156 -== 3.6.31 Fault simulation == 76 +