Skip to Content

Changes for page 3.6 Battery protection

Last modified by Admin on 2025/04/09 12:25
From version 33.5
edited by Admin
on 2024/11/21 19:00
Change comment: There is no comment for this version
To version 33.7
edited by Admin
on 2024/11/21 19:03
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -410,6 +410,10 @@
410 410  
411 411  * charging and discharging contactors are open, but the “Charging current present” or “Discharging current present” signal is set.
412 412  
413 +(% class="box warningmessage" %)
414 +(((
415 +If there is the “Stuck contactor error”, the **“Critical error” **is generated and **all relays open.**
416 +)))
413 413  
414 414  == 3.6.14 Contactor feedback check ==
415 415  
... ... @@ -516,7 +516,7 @@
516 516  
517 517  (% class="box warningmessage" %)
518 518  (((
519 -If there is the “No temp. sensors” or “Temp. sensor is shorted” error, **the “Critical error” is generated and all relays open.**
523 +If there is the “No temp. sensors” or “Temp. sensor is shorted” error, the **“Critical error” **is generated and **all relays open.**
520 520  )))
521 521  
522 522  == 3.6.18 Logic high temperature protection ==
... ... @@ -570,7 +570,7 @@
570 570  
571 571  (% class="box warningmessage" %)
572 572  (((
573 -If there is the "Logic offline" error, **the “Critical error” is generated and all relays open.**
577 +If there is the "Logic offline" error, the **“Critical error”** is generated and **all relays open.**
574 574  )))
575 575  
576 576  == 3.6.20 Cell count protection ==
... ... @@ -599,7 +599,7 @@
599 599  
600 600  (% class="box warningmessage" %)
601 601  (((
602 -If there is the "Cell count error",** the “Critical error” is generated and all relays open.**
606 +If there is the "Cell count error",** **the **“Critical error”** is generated and **all relays open.**
603 603  )))
604 604  
605 605  == 3.6.21 Logic count protection ==
... ... @@ -627,7 +627,7 @@
627 627  
628 628  (% class="box warningmessage" %)
629 629  (((
630 -If there is the "Logic count error", **the “Critical error” is generated and all relays open.**
634 +If there is the "Logic count error", the **“Critical error” **is generated and **all relays open.**
631 631  )))
632 632  
633 633  == 3.6.22 WDT protection ==
... ... @@ -650,7 +650,7 @@
650 650  
651 651  (% class="box warningmessage" %)
652 652  (((
653 -If there is the "WDT reset" error, **the “Critical error” is generated and all relays open.**
657 +If there is the "WDT reset" error, the **“Critical error”** is generated and** all relays open.**
654 654  )))
655 655  
656 656  == 3.6.23 Insulation monitoring ==
... ... @@ -724,7 +724,10 @@
724 724  
725 725  The “General error” is cleared if there are no errors from selected list during the “Delay before clearing the error” time.
726 726  
731 +(% class="box infomessage" %)
732 +(((
727 727  The "General error" is //indicative //and can be linked to any discrete output of the board.
734 +)))
728 728  
729 729  == 3.6.26 Low SOC signal ==
730 730  
... ... @@ -749,7 +749,10 @@
749 749  
750 750  * the battery SOC is greater than the “Tolerant SOC” during the “Delay before clearing the signal” time.
751 751  
759 +(% class="box infomessage" %)
760 +(((
752 752  The "Low SOC signal" is //indicative //and can be linked to any discrete output of the board.
762 +)))
753 753  
754 754  == 3.6.27 High charging current signal ==
755 755  
... ... @@ -774,7 +774,10 @@
774 774  
775 775  * the measured current is less than the “Tolerant charging current” value during the “Delay before clearing the signal” time.
776 776  
787 +(% class="box infomessage" %)
788 +(((
777 777  The "High charging current" signal is //indicative //and can be linked to any discrete output of the board.
790 +)))
778 778  
779 779  == 3.6.28 Heater control ==
780 780  
... ... @@ -804,7 +804,7 @@
804 804  
805 805  (% class="box infomessage" %)
806 806  (((
807 -If there is the "Heater" signal, the heater relay closes and/or a signal is output to the corresponded digital output.
820 +If there is the "Heater" signal, the **heater **relay closes and/or a signal is output to the corresponded digital output.
808 808  )))
809 809  
810 810  == 3.6.29 Heater (AUX) control ==
... ... @@ -835,7 +835,7 @@
835 835  
836 836  (% class="box infomessage" %)
837 837  (((
838 -If there is the "Heater (AUX)" signal, the auxiliary heater relay closes and/or a signal is output to the corresponded digital output.
851 +If there is the "Heater (AUX)" signal, the **auxiliary heater **relay closes and/or a signal is output to the corresponded digital output.
839 839  )))
840 840  
841 841  == 3.6.30 Cooler control ==
... ... @@ -866,7 +866,7 @@
866 866  
867 867  (% class="box infomessage" %)
868 868  (((
869 -If there is the "Cooler" signal, the cooler relay closes and/or a signal is output to the corresponded digital output.
882 +If there is the "Cooler" signal, the **cooler **relay closes and/or a signal is output to the corresponded digital output.
870 870  )))
871 871  
872 872  == 3.6.31 Fault simulation ==