3.6 Battery protection - Movicom Electric Docs

1

The BMS Main 2.x board continuously monitors the state of the cells, BMS Logic boards, the external environment and, when detecting abnormalities, protects the battery and system components from damage.

2

3

== 3.6.1 Overcurrent protection ==

4

5

To change the current protection of the battery, select the menu "Protections → Overcurrent protection":

6

7

[[Overcurrent protection settings>>image:1732211959984-118.png||data-xwiki-image-style-alignment="center" height="266" width="386"]]

In this section:

* Enable – a flag to enable the protection;

13

* Maximum charging current, А;

14

* Tolerant charging current, А;

15

* Maximum discharging current, А;

16

* Tolerant discharging current, А;

17

* Delay before setting the error, second;

18

* Delay before clearing the error, second;

19

* Lock the error until the device is reset – a flag to block the error until the board is restarted.

20

21

As a result of operation of the current protection, the "Overcurrent" error is generated.

22

23

Error generation conditions:

24

25

* the current is positive (charging), and its modulo value is greater than the “Maximum charging current” value for the “Delay before setting the error” time;

26

* the current is negative (discharging), and its modulo value is greater than the “Maximum discharging current” value for the “Delay before setting the error” time.

27

28

Conditions for removing the error:

29

30

* the current is positive (charging) or zero, and its modulo value is less than the “Tolerant charging current” value for the “Delay before clearing the error” time;

31

* the current is negative (discharging), and its modulo value is less than the “Tolerant discharging current” value for the “Delay before clearing the error” time.

32

33

(% class="box infomessage" %)

34

(((

35

If there is the "Overcurrent" error, the charging relay and discharging relay open.

36

)))

37

38

== 3.6.2 Undervoltage protection ==

39

40

The board implements battery protection from too low or too high voltage on the cells.

41

42

To change the battery protection parameters from low voltage on the cells, select the menu "Protections → Undervoltage protection":

43

44

[[Undervoltage protection settings>>image:1732212212350-294.png||data-xwiki-image-style-alignment="center" height="207" width="359"]]

In this section:

* Enable – a flag to enable the protection;

49

* Minimum cell voltage, V;

50

* Tolerant cell voltage, V;

51

* Delay before setting the error, second;

52

* Delay before clearing the error, second;

53

* Lock the error until the device is reset.

54

55

As a result of the operation of battery protection from low voltage, the "Undervoltage" error is generated.

56

57

Error generation conditions:

58

59

* the minimum voltage among all cells of the battery is less than the “Minimum cell voltage” value for the “Delay before setting the error” time.

60

61

Conditions for removing the error:

62

63

* the minimum voltage among all cells of the battery is greater than the “Tolerant cell voltage” value for the “Delay before clearing the error” time.

64

65

(% class="box infomessage" %)

66

(((

67

If there is the "Undervoltage" error, the discharging relay opens.

68

)))

69

70

3.6.3 Overvoltage protection

71

72

To change the battery protection parameters from high voltage on the cells, select the menu "Protections → Overvoltage protection":

73

74

[[image:1732212357972-295.png]]

In this section:

* Enable – a flag to enable the protection;

79

* Maximum cell voltage, V;

80

* Tolerant cell voltage, V;

81

* Delay before setting the error, second;

82

* Delay before clearing the error, second;

83

* Switch off the discharging relay on error – a flag to open the discharging relay when the "Overvoltage" error is generated;

84

* Lock the error until the device is reset.

85

86

As a result of the operation of the battery protection from high voltage, the "Overvoltage" error is generated.

87

88

Error generation conditions:

89

90

* the maximum voltage among all cells of the battery is greater than the “Maximum cell voltage” value for the “Delay before setting the error” time.

91

92

Conditions for removing the error:

93

94

* the maximum voltage among all cells of the battery is less than the “Tolerant cell voltage” value for the “Delay before clearing the error” time.

95

96

(% class="box infomessage" %)

97

(((

98

If there is the "Overvoltage" error, the charging relay and discharging relay opens (if the “Switch off the discharging relay on error” flag is set).

99

)))

100

101

== 3.6.4 Low temperature protection ==

102

103

The board implements battery protection from too low temperature.

104

105

To change the battery protection parameters from low temperature, select the menu "Protections → Low temperature protection":

In this section:

* Enable – a flag to enable the protection;

111

* Minimum charging temperature, °C;

112

* Tolerant charging temperature, °C;

113

* Minimum discharging temperature, °C;

114

* Tolerant discharging temperature, °C;

115

* Delay before setting the error, second;

116

* Delay before clearing the error, second;

117

* Lock the error until the device is reset.

118

119

As a result of the operation of the battery protection from low temperature, the "Low CH temperature" or “Low DCH temperature” error is generated.

120

121

Error generation conditions:

122

123

* the minimum temperature among all cells of the battery is less than the “Minimum charging (discharging) temperature” value for the “Delay before setting the error” time.

124

125

Conditions for removing the error:

126

127

* the minimum temperature among all cells of the battery is greater than the “Tolerant charging (discharging) temperature” value for the “Delay before clearing the error” time.

128

129

(% class="box infomessage" %)

130

(((

131

If there is the "Low CH temperature" error, the charging relay opens. If there is the "Low DCH temperature" error, the discharging relay opens.

132

)))

133

134

== 3.6.5 High temperature protection ==

135

136

The board implements battery protection from too high temperature.

137

138

To change the battery protection parameters from high temperature, select the menu "Protections → High temperature protection":

In this section:

* Enable – a flag to enable the protection;

143

* Maximum charging temperature, °C;

144

* Tolerant charging temperature, °C;

145

* Maximum discharging temperature, °C;

146

* Tolerant discharging temperature, °C;

147

* Delay before setting the error, second;

148

* Delay before clearing the error, second;

149

* Lock the error until the device is reset.

150

151

As a result of the operation of the battery protection from high temperature, the "High CH temperature" or “High DCH temperature” error is generated.

152

153

Error generation conditions:

154

155

* the maximum temperature among all cells of the battery is greater than the “Maximum charging (discharging) temperature” value for the “Delay before setting the error” time.

156

157

Conditions for removing the error:

158

159

* the maximum temperature among all cells of the battery is less than the “Tolerant charging (discharging) temperature” value for the “Delay before clearing the error” time.

160

161

(% class="box infomessage" %)

162

(((

163

If there is the "High CH temperature" error, the charging relay opens.

164

If there is the "High DCH temperature" error, the discharging relay opens.

165

)))

166