Skip to Content

Changes for page 3.5 Battery control

Last modified by Admin on 2025/06/11 15:20
From version 24.1
edited by Admin
on 2025/02/19 10:43
Change comment: There is no comment for this version
To version 26.2
edited by Admin
on 2025/06/11 15:15
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -4,7 +4,7 @@
4 4  (% data-numbered-headings-start="5" style="--numbered-headings-start: 4;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
5 5  == Battery control ==
6 6  
7 -=== Charge control ===
7 +=== Charging control ===
8 8  
9 9  There are two relays that serve charging the battery: a charging relay and an allow charging relay. With the help of the allow charging relay, the BMS commands the charger to start or stop charging.
10 10  
... ... @@ -74,7 +74,7 @@
74 74  2) the "Delay before recharging" time has passed since the opening of the allow charging relay.
75 75  )))
76 76  
77 -=== Discharge control ===
77 +=== Discharging control ===
78 78  
79 79  The board has a discharging relay to connect battery to the load.
80 80  
... ... @@ -117,7 +117,7 @@
117 117  
118 118  To change the parameters of the battery discharge control algorithm, select the menu "Cells → Discharging control":
119 119  
120 -[[image:1739961703149-845.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="748" width="440"]]
120 +[[image:1749654838818-400.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="828" width="446"]]
121 121  
122 122  In this section:
123 123  
... ... @@ -136,7 +136,8 @@
136 136  * Precharge time – a duration of closing the precharge relay before closing the discharging relay, millisecond;
137 137  * Precharge current threshold to start discharging – a minimum current value to finish precharging and start discharge, A;
138 138  * Voltage to clear the “Ready to discharge” signal – a threshold U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if the voltage of any cell is below this level, the “Ready to discharge” signal is cleared;
139 -* Voltage to reset the “Ready to discharge” signal – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set.
139 +* Voltage to reset the “Ready to discharge” signal – a tolerant U,,ocv,, (corrected due to current and cell resistance) voltage level on the cell, V; if all cells voltages are above the tolerant level, the “Ready to discharge” signal is set;
140 +* Treat negative currents as zero currents for generating the "Read y to charge" signal – a flag to disable voltage correction
140 140  
141 141  === Discharging (AUX) control ===
142 142  
... ... @@ -170,7 +170,7 @@
170 170  
171 171  === Charging/Discharging control ===
172 172  
173 - BMS Main 2.x allows to control charging/discharging contactor that combines algorithms of charging and discharging contactor. It behaves as charging contactor when «Charge request» or «Charger connected» are set, otherwise – as discharging contactor.
174 + BMS Main 2.x allows to control charging/discharging contactor that combines algorithms of charging and discharging contactor. It behaves as [[charging>>doc:||anchor="HChargingcontrol"]] contactor when «Charge request» or «Charger connected» are set, otherwise – as [[discharging>>doc:||anchor="HDischargingcontrol"]] contactor.
174 174  
175 175  To change the parameters of the charging/discharging algorithm, select the menu "Cells → Charging/Discharging control":
176 176  
1749654838818-400.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +60.9 KB
Content