Skip to Content

Wiki source code of 3.3 Input and output signals

Version 26.2 by Admin on 2025/02/19 10:14
Hide last authors
Admin 20.1 1 (% data-numbered-headings-start="3" style="--numbered-headings-start: 2;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 = Configuration =
Admin 1.1 3
Admin 20.1 4 (% data-numbered-headings-start="3" style="--numbered-headings-start: 2;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
5 == Input and output signals ==
6
7 === Input signals ===
8
Admin 14.1 9 The BMS Main 2.x board has **4 discrete inputs** of the "dry contact" type. For each discrete input, its purpose and the inversion requirement are specified.
Admin 2.2 10
Admin 14.1 11 BMS Main 2.x board has **4 analog inputs** for connecting current, temperature and humidity sensors.
Admin 2.2 12
Admin 16.1 13 The order of the numbering of the discrete and analog inputs corresponds to the order of the numbering on the board.
14
Admin 14.1 15 (% id="cke_bm_2415S" style="display:none" %) (%%)To configure the input discrete and analog signals, select the menu "Signals → Input signals":
16
Admin 17.1 17 [[image:1732201986070-992.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="290" width="272"]]
Admin 14.1 18
Admin 26.2 19 A list of available **discrete input assignments **is available in [[Input signals>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HInputsignals"]].
Admin 14.1 20
Admin 23.1 21 If the "Signal from the battery cover" assignment is selected, the discrete input is used to monitor the state of the battery cover (see [[Battery cover protection>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HBatterycoverprotection"]]).
Admin 2.2 22
Admin 22.1 23 if the "Charger connected" assignment is selected, the discrete input is involved in the algorithms of charge and discharge control (see [[Charge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HChargecontrol"]] and [[Discharge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HDischargecontrol"]]).
Admin 2.2 24
Admin 22.1 25 If the "Power up/down request" assignment is selected, the discrete input is involved in the algorithms of opening the charging and discharging relays and sending acknowledgment of power down to the external equipment (see [[Charge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HChargecontrol"]] and [[Discharge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HDischargecontrol"]]).
Admin 3.3 26
Admin 3.4 27 If the “Inhibit charging” assignment is selected, the discrete input is used to open the charging relay.
Admin 3.3 28
Admin 3.4 29 If the “Inhibit discharging” assignment is selected, the discrete input is used to open the discharging relay.
Admin 3.3 30
Admin 23.1 31 If the “CH contactor feedback”, “DCH contactor feedback”, “PCH contactor feedback”, “CH/DCH contactor feedback” or “Main contactor feedback” assignment is selected, the discrete input is involved in monitoring the corresponding contactor’s feedback signal (see [[Contactor feedback check>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HContactorfeedbackcheck"]]).
Admin 3.3 32
Admin 22.1 33 If the “Charge request”, “Precharge request” or “Discharge request” assignment is selected, the discrete input is used to control opening the corresponding contactor (see [[Charge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HChargecontrol"]] and [[Discharge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HDischargecontrol"]]).
Admin 3.3 34
Admin 23.1 35 If the “Insulation status” assignment is selected, the discrete input is used to monitor a signal from an external insulation monitoring device (see [[Insulation monitoring>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HInsulationmonitoring"]]).
Admin 3.3 36
Admin 11.2 37
Admin 18.1 38 **Analog inputs** in this section:
Admin 3.3 39
Admin 14.1 40 * No input;
41 * Current sensor;
42 * Current zero level;
43 * Temperature sensor;
44 * Humidity sensor;
45 * Current sensor (AUX) – additional current sensor for measuring current in a series of cells;
46 * Current zero level (AUX) – zero level bus for additional current sensor.
47
48 **Assignment of analog inputs must be selected as follows**:
49
Admin 6.2 50 * Analog Input #1 – Current sensor;
Admin 4.7 51 * Analog Input #2 – No input / Current sensor reference line / Current sensor (2nd range) (see note);
52 * Analog Input #3 – No input / Temperature sensor / Current sensor (AUX);
53 * Analog Input #4 – No input / Humidity sensor / Current reference line (AUX) / Current sensor (2nd range) (AUX).
Admin 3.3 54
55 (% class="box warningmessage" %)
56 (((
Admin 21.1 57 **Important**: the connection of an additional current sensor (AUX) is possible for special hardware revision of the BMS Main 2.x board. Using an additional current sensor is possible in the configuration when BMS Main serves two galvanically isolated cell series (see [[Series balancing>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.4 Battery parameters.WebHome||anchor="HSeriesbalancing"]]).
Admin 3.3 58 )))
59
60 (% class="box warningmessage" %)
61 (((
Admin 3.4 62 **Warning: **reassignment of analog inputs is **unacceptable.**
Admin 3.3 63 )))
64
Admin 3.4 65 (% class="box infomessage" %)
66 (((
Admin 4.3 67 **Note:** The default setting for Analog input #2 is "No signal". If it is necessary to use a current sensor with an additional zero level signal, set the "Current sensor reference line" assignment.
Admin 3.4 68 )))
69
Admin 20.1 70 === Current sensor ===
Admin 4.2 71
72 After selecting the assignment of the analog inputs, you need to configure the parameters of the sensors connected to the board.
Admin 4.3 73
74 To configure the current sensor parameters, select the menu "Signals → Current sensor":
Admin 6.2 75
Admin 17.1 76 [[image:1732202357233-620.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="453" width="284"]]
Admin 6.2 77
78 In the «Primary sensor» и «Auxiliary sensor» sections:
79
80 * Sensor type – drop-down menu with supported sensor types;
81 * Nominal current – rated current of the sensor according to the datasheet, А;
82 * Sensitivity – sensitivity of the current sensor according to the datasheet, V / I,,nominal.,,;
83 * Zero level – level "0A" of the current sensor, V;
84 * Multiply the charging current (experimental) – experimental flag for scaling the charging current by given multiplier;
85 * Multiplier – charging current multiplier;
86
87 In the «Options» section:
88
89 * Calibrate sensor on startup – calibration flag (zero level setting) of the current sensor when the board is started;
90 * Calibration time – calibration time of the current sensor, second;
91 * System consumption (current offset) – consumption of the BMS system from the battery, A; This setting is used to adjust the current sensor;
92 * Set sensor zero level – command set the zero level of the current sensor (used for service purposes).
93
Admin 7.2 94 (% class="box infomessage" %)
95 (((
Admin 7.4 96 If the "Sensor type" is selected, the “Nominal current” and “Sensitivity” fields are automatically filled.
97 If the "Sensor type" has no necessary preset, the “Nominal current” and “Sensitivity” parameters must be **manually **entered.
Admin 7.2 98 )))
Admin 6.2 99
Admin 8.2 100 Calibration of the current sensor (“Calibrate sensor on startup” flag) is necessary if the sensor does not have a reference line (zero level signal).
101
Admin 20.1 102 === Current shunt sensor ===
Admin 8.2 103
104 To configure the shunt current sensor parameters, select the menu "Signals → Current shunt sensor":
105
Admin 17.1 106 [[image:1732202640889-562.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="342" width="265"]]
Admin 8.3 107
108 In this section:
109
110 * Settings:
Admin 16.1 111 ** Enable – a flag to start interaction with BMS Current Sensor (if interaction is enabled then BMS doesn’t use Hall-Effect current sensor which settings are described in the menu "Signals → Current sensor");
112 ** Node ID – an address of BMS Current Sensor in CANopen network;
113 ** Dispatch timeout – timeout of dispatching packages from BMS Current Sensor (if no data is being received from current sensor during this time, the “Shunt offline” flag is set), millisecond;
114 ** Zero level threshold – T,,0,, level, A (if module of instantaneous current (I,,I,,) which is received from shunt sensor is lower than T,,0,,, BMS will assume that current flowing through the battery is zero);
115 ** Mean level threshold – TM level, A (if module of instantaneous current (I,,I,,) which is received from shunt sensor is between T,,M,, and T,,0,,, BMS will use mean value of current I,,M,,; if I,,I,, is greater than T,,M,,, BMS will use instantaneous value of current I,,I,,);
116 ** Invert – a flag to invert current values;
Admin 8.3 117 * Sensor state:
118 ** Online – a flag showing that the communication with the BMS Current Sensor is established;
119 ** Errors – a list of internal errors of the shunt sensor;
120 ** Current – an instantaneous value of current measured by the BMS Current Sensor, A (measuring frequency is 50 Hz);
121 ** Current (mean) – a mean value of current measured by the BMS Current Sensor, A (the value is calculated as an average of 100 consistent measurements);
122 ** Temperature – a temperature of the shunt sensor, °C.
123
Admin 20.1 124 === Temperature sensor ===
Admin 8.5 125
126 To configure the temperature sensor parameters, select the menu "Signals → Temperature sensor":
Admin 9.2 127
Admin 17.1 128 [[image:1732204766138-628.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="112" width="256"]]
Admin 9.2 129
130 In this section:
131
Admin 23.7 132 * Type – type of temperature sensors;
Admin 26.1 133 * Mask – mask to ignore the temperature from the corresponding temperature sensors; bit //i// corresponds to temperature input //#(i+1)// of each BMS Logic device; mask 0x5 means that the BMS marks all temperature sensors connected to inputs #1 and #3 of each BMS Logic device as missing and doesn't use them in calculations.
Admin 9.2 134
135 (% class="box infomessage" %)
136 (((
137 **Note:** Temperature sensors connected to the BMS Main 2.x and BMS Logic boards must be the same type.
138 )))
Admin 10.2 139
Admin 20.1 140 === Humidity sensor ===
Admin 10.2 141
142 To set the humidity sensor parameters, select the menu "Signals → Humidity sensor":
143
Admin 17.1 144 [[image:1732204899160-307.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="120" width="195"]]
Admin 10.3 145
146 In this section:
147
148 * Type – type of the humidity sensor.
149
Admin 20.1 150 === Output signals ===
Admin 11.2 151
Admin 16.1 152 The BMS Main 2.x board has **4 discrete outputs**. For each discrete output, its purpose and inversion requirement are specified.
Admin 11.2 153
Admin 16.1 154 The BMS Main 2.x board has **4 solid-state relays** (#1 and #2 of them are bipolar, and the #3 and #4 are unipolar). For each relay, its purpose and inversion requirement are specified.
Admin 14.1 155
Admin 16.1 156 The order of the numbering of the discrete outputs and the relay corresponds to the order of the numbering on the board.
157
Admin 14.1 158 To configure output discrete signals and relays, select the menu "Signals → Output signals":
159
Admin 17.1 160 [[image:1732205046156-597.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="346" width="295"]]
Admin 14.1 161
Admin 26.2 162 A list of available **discrete input assignments **is available in [[Input signals>>doc:Battery management systems.Additional information.1\. Battery controllers\: signals and errors.WebHome||anchor="HInputsignals"]].
Admin 14.1 163
Admin 23.1 164 If the "Low SOC" assignment is selected, the output indicates the low battery charge level (see [[Low SOC signal>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HLowSOCsignal"]]).
Admin 11.2 165
Admin 23.1 166 If the "High battery charge current" assignment is selected, the output indicates that the charging current exceeds the predefined value (see [[High charging current signal>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HHighchargingcurrentsignal"]]).
Admin 11.2 167
Admin 23.1 168 If the "Cooler" assignment is selected, the output indicates the overheating of the battery (see [[High temperature protection>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HHightemperatureprotection"]]).
Admin 11.2 169
Admin 23.1 170 If the "Heater" assignment is selected, the output indicates the low battery temperature signal (see [[Low temperature protection>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HLowtemperatureprotection"]]).
Admin 11.2 171
Admin 22.1 172 If the "Allow charging" assignment is selected, the output is used to give the charger the allowance to charge the battery (see [[Charge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HChargecontrol"]]).
Admin 11.2 173
Admin 22.1 174 If the "Precharging" assignment is selected, the output is used to charge the capacitive load (see [[Discharge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HDischargecontrol"]]).
Admin 11.2 175
Admin 22.1 176 If the "Acknowledgement of power down" assignment is selected, the output is used to acknowledge power down of the BMS. Acknowledgement is outputted when the charge and discharge relays have been opened on power down request (see [[Charge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HChargecontrol"]] and [[Discharge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HDischargecontrol"]]).
Admin 11.2 177
Admin 23.1 178 If the "Power up" assignment is selected, the output is used to indicate the power status of BMS (see [[Power down control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HPowerdowncontrol"]]).
Admin 11.2 179
180
Admin 18.1 181 **Relay assignments** in this section:
Admin 11.2 182
183 * No relay;
184 * Charging;
185 * Discharging;
186 * Allow charging;
187 * Cooler;
188 * Heater;
189 * Precharging;
190 * Balancing series 1;
191 * Balancing series 2;
192 * Discharging (AUX);
193 * Main contactor;
194 * Power up.
195
Admin 22.1 196 If the "Charging" assignment is selected, the relay is used to charge the battery (see [[Charge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HChargecontrol"]]).
Admin 11.2 197
Admin 22.1 198 If the "Discharging" assignment is selected, the relay is used to connect battery to the load (see [[Discharge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HDischargecontrol"]]).
Admin 11.2 199
Admin 22.1 200 If the "Allow charging" assignment is selected, the relay is used to give the charger an allowance to charge the battery (see [[Charge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HChargecontrol"]]).
Admin 11.2 201
Admin 23.1 202 If the "Cooler" assignment is selected, the relay receives a signal indicating overheating of the battery (see [[High temperature protection>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HHightemperatureprotection"]]) or the signal "Cooler" (see [[Cooler control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HCoolercontrol"]]).
Admin 11.2 203
Admin 23.1 204 If the "Heater" assignment is selected, a low battery temperature signal is outputted to the relay (see [[Low temperature protection>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HLowtemperatureprotection"]]) or a signal "Heater" (see [[Heater control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.6 Battery protection.WebHome||anchor="HHeatercontrol"]]).
Admin 11.2 205
Admin 22.1 206 If the "Precharging" assignment is selected, the relay is used to charge the capacitive load (see [[Discharge control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HDischargecontrol"]]).
Admin 11.2 207
Admin 21.1 208 If the "Balancing series 1" assignment is selected, the relay is used to connect a balancing resistor to the cell series 1 (see [[Series balancing>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.4 Battery parameters.WebHome||anchor="HSeriesbalancing"]]).
Admin 11.2 209
Admin 21.1 210 If the "Balancing series 2" assignment is selected, the relay is used to connect a balancing resistor to the cell series 2 (see [[Series balancing>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.4 Battery parameters.WebHome||anchor="HSeriesbalancing"]]).
Admin 11.2 211
Admin 22.1 212 If the "Discharging (AUX)" assignment is selected, the relay is used to power external equipment (see [[Discharging (AUX) control>>doc:Battery management systems.BMS Main 2\.1.3\. Configuration.3\.5 Battery control.WebHome||anchor="HDischarging(AUX)control"]]).
Admin 11.2 213
214 If the "Main contactor" assignment is selected, the relay is used to close the main contactor in the common (minus) power bus.
215
216 If the "Power up" assignment is selected, the relay is used to close the contactor in the BMS Main power bus.