Wiki source code of 2. Connection

Version 15.1 by Admin on 2024/11/13 17:09

version	line-number	content
1.2	1	= Headers =
	2
	3	The BMS Main 2.1 headers are shown in figure below.
	4
	5	[[The BMS Main 2.1 headers>>image:1731516393377-928.jpeg\|\|height="430" width="428"]]
	6
13.1	7	=== P1 – header for power supply ===
2.2	8
12.2	9	[[image:1731516593096-166.png\|\|data-xwiki-image-style-alignment="center"]]
2.2	10
14.1	11	\|(% style="width:100px" %)Pin\|(% style="width:502px" %)Name\|Description
	12	\|(% style="width:100px" %)1\|(% style="width:502px" %)GND\|Ground
	13	\|(% style="width:100px" %)2\|(% style="width:502px" %)V+\|Supply voltage 9-30V
4.2	14
13.1	15	=== P15 – header for BMS Logic ===
4.2	16
12.2	17	[[image:1731516577472-301.png\|\|data-xwiki-image-style-alignment="center"]]
4.2	18
14.1	19	\|(% style="width:100px" %)Pin\|(% style="width:290px" %)Name\|Description
	20	\|(% style="width:100px" %)1\|(% style="width:290px" %)RS485_A\|RS-485 line A for communication with BMS Logic
	21	\|(% style="width:100px" %)2\|(% style="width:290px" %)RS485_B\|RS-485 line B for communication with BMS Logic
	22	\|(% style="width:100px" %)3\|(% style="width:290px" %)+5V\|Supply voltage for BMS Logic
	23	\|(% style="width:100px" %)4\|(% style="width:290px" %)GND\|Ground
5.2	24
13.1	25	=== P12 – header for current sensor ===
5.2	26
12.2	27	[[image:1731516685999-633.png\|\|data-xwiki-image-style-alignment="center"]]
5.3	28
15.1	29	\|(% style="width:100px" %)Pin\|Name\|Description
	30	\|(% style="width:100px" %)1\|+5V\|Supply voltage for the current sensor 5V, max 50 mA
	31	\|(% style="width:100px" %)2\|GND\|Ground
	32	\|(% style="width:100px" %)3\|Vcs\|ADC input (current sensor output)
	33	\|(% style="width:100px" %)4\|Vref\|ADC input (current sensor reference signal)
5.3	34
13.1	35	=== P13 – header for humidity sensor ===
5.3	36
6.2	37	[[image:1731516942455-641.png\|\|data-xwiki-image-style-alignment="center"]]
	38
15.1	39	\|(% style="width:100px" %)Pin\|Name\|Description
	40	\|(% style="width:100px" %)1\|+5V\|Supply voltage 5 V, max 50 mA
	41	\|(% style="width:100px" %)2\|GND\|Ground
	42	\|(% style="width:100px" %)3\|Vhs\|ADC input (humidity sensor output)
	43	\|(% style="width:100px" %)4\|Vts\|ADC input (temperature sensor output)
6.2	44
13.1	45	=== P8 – header of relay 1 ===
6.2	46
12.2	47	[[image:1731517023208-641.png\|\|data-xwiki-image-style-alignment="center"]]
6.2	48
	49	By default, relay 1 is used to control the discharging contactor.
	50
15.1	51	\|(% style="width:100px" %)Pin\|Name\|Description
	52	\|(% style="width:100px" %)1\|V+\|Switching voltage (up to 55V, max 2A)
	53	\|(% style="width:100px" %)2\|NO\|Normally open contact
6.2	54
13.1	55	=== P9 – header of relay 2 ===
11.2	56
12.2	57	[[image:1731517025702-799.png\|\|data-xwiki-image-style-alignment="center"]]
11.2	58
	59	By default, relay 2 is used to output the “Allow charging” signal.
	60
15.1	61	\|(% style="width:100px" %)Pin\|Name\|Description
	62	\|(% style="width:100px" %)1\|V+\|Switching voltage (up to 55V, max 2A)
	63	\|(% style="width:100px" %)2\|NO\|Normally open contact
6.2	64
13.1	65	=== P6 – header of relay 3 ===
6.2	66
12.2	67	[[image:1731517025702-799.png\|\|data-xwiki-image-style-alignment="center"]]
6.2	68
11.2	69	By default, relay 3 is used to control the charging contactor.
6.2	70
15.1	71	\|(% style="width:100px" %)Pin\|Name\|Description
	72	\|(% style="width:100px" %)1\|V+\|Switching voltage (up to 55V, max 8A)
	73	\|(% style="width:100px" %)2\|NO\|Normally open contact
6.2	74
13.1	75	=== P7 – header of relay 4 ===
6.2	76
12.2	77	[[image:1731517025702-799.png\|\|data-xwiki-image-style-alignment="center"]]
11.2	78
	79	By default, relay 4 is used to control the heater.
	80
15.1	81	\|(% style="width:100px" %)Pin\|Name\|Description
	82	\|(% style="width:100px" %)1\|V+\|Switching voltage (up to 55V, max 8A)
	83	\|(% style="width:100px" %)2\|NO\|Normally open contact
6.2	84
13.1	85	=== P14 – header for CAN and RS-485 interfaces ===
6.2	86
12.2	87	[[image:1731517180930-597.png\|\|data-xwiki-image-style-alignment="center"]]
6.2	88
15.1	89	\|(% style="width:100px" %)Pin\|Name\|Description
	90	\|(% style="width:100px" %)1\|EXT_RS485_A\|RS-485 line A for communication with external equipment
	91	\|(% style="width:100px" %)2\|CAN_H\|CAN H line for communication with external equipment
	92	\|(% style="width:100px" %)3\|+5V_CAN\|Supply voltage 5V for external devices, max 200 mA
	93	\|(% style="width:100px" %)4\|EXT_RS485_B\|RS-485 line B for communication with external equipment
	94	\|(% style="width:100px" %)5\|CAN_L\|CAN L line for communication with external equipment
	95	\|(% style="width:100px" %)6\|GND_CAN\|Ground
11.2	96
13.1	97	=== P21 – CAN termination resistor jumper ===
11.2	98
12.2	99	[[image:1731517188900-976.png\|\|data-xwiki-image-style-alignment="center"]]
11.2	100
	101	To connect the termination resistor between the lines CAN_H and CAN_L, install a jumper, according to the P21 pinout:
	102
15.1	103	\|(% style="width:100px" %)Pin\|Name\|Description
	104	\|(% style="width:100px" %)1-2\|120 Ohm\|Termination resistor 120 Ohm is connected
	105	\|(% style="width:100px" %)2-3\|-\|Termination resistor 120 Ohm is not connected
11.2	106
13.1	107	=== P22 - RS-485 termination resistor jumper ===
11.2	108
12.2	109	[[image:1731517195672-298.png\|\|data-xwiki-image-style-alignment="center"]]
11.2	110
	111	To connect the termination resistor between the EXT_RS485_A and EXT_RS485_B lines, install a jumper according to the P22 pinout:
	112
15.1	113	\|(% style="width:100px" %)Pin\|Name\|Description
	114	\|(% style="width:100px" %)1-2\|120 Ohm\|Terminating resistor 120 Ohm is connected
	115	\|(% style="width:100px" %)2-3\|-\|Terminating resistor 120 Ohm is not connected
11.2	116
13.1	117	=== P11 – header for discrete inputs/outputs ===
11.2	118
12.2	119	[[image:1731517206246-979.png\|\|data-xwiki-image-style-alignment="center"]]
11.2	120
15.1	121	\|(% style="width:100px" %)Pin\|Name\|Description
	122	\|(% style="width:100px" %)16\|IN_1\|Discrete input #1 “dry contact” (+5V)
	123	\|(% style="width:100px" %)8\|GND_1\|Discrete input #1 “dry contact” (ground)
	124	\|(% style="width:100px" %)15\|IN_2\|Discrete input #2 “dry contact” (+5V)
	125	\|(% style="width:100px" %)7\|GND_2\|Discrete input #2 “dry contact” (ground)
	126	\|(% style="width:100px" %)14\|IN_3\|Discrete input #3 “dry contact” (+5V)
	127	\|(% style="width:100px" %)6\|GND_3\|Discrete input #3 “dry contact” (ground)
	128	\|(% style="width:100px" %)13\|IN_4\|Discrete input #4 “dry contact” (+5V)
	129	\|(% style="width:100px" %)5\|GND_4\|Discrete input #4 “dry contact” (ground)
	130	\|(% style="width:100px" %)12\|OUT_4\|Discrete output #4 (+5V, 20mA)
	131	\|(% style="width:100px" %)4\|GND_OUT_4\|Discrete output #4 (ground)
	132	\|(% style="width:100px" %)11\|OUT_3\|Discrete output #3 (+5V, 20mA)
	133	\|(% style="width:100px" %)3\|GND_OUT_3\|Discrete output #3 (ground)
	134	\|(% style="width:100px" %)10\|OUT_2\|Discrete output #2 (+5V, 20mA)
	135	\|(% style="width:100px" %)2\|GND_OUT_2\|Discrete output #2 (ground)
	136	\|(% style="width:100px" %)9\|OUT_1\|Discrete output #1 (+5V, 20mA)
	137	\|(% style="width:100px" %)1\|GND_OUT_1\|Discrete output #1 (ground)
11.2	138
13.1	139	= Indicators =
11.2	140
13.1	141	=== DS1 – power indicator ===
	142
15.1	143	\|(% style="width:100px" %)State\|Description
	144	\|(% style="width:100px" %)Lights red\|The device is powered
	145	\|(% style="width:100px" %)Off\|The device is not powered
11.2	146
13.1	147	=== DS2 – operation indicator ===
11.2	148
15.1	149	\|(% style="width:100px" %)State\|Description
	150	\|(% style="width:100px" %)Blinking green\|The BMS firmware is running
	151	\|(% style="width:100px" %)Off\|The BMS firmware is not running
11.2	152
13.1	153	=== DS3 – communication indicator ===
11.2	154
15.1	155	\|(% style="width:100px" %)State\|Description
	156	\|(% style="width:100px" %)Blinking yellow (2Hz)\|Initializing communication with BMS Logic boards
	157	\|(% style="width:100px" %)Blinking yellow (25Hz)\|Communication with BMS Logic is established
11.2	158
13.1	159	=== DS4 – error indicator ===
11.2	160
15.1	161	\|(% style="width:100px" %)State\|Description
	162	\|(% style="width:100px" %)Blinking red\|Errors in communication with BMS Logic
11.2	163
13.1	164	=== DS7 – relay 1 indicator ===
11.2	165
15.1	166	\|(% style="width:100px" %)State\|Description
	167	\|(% style="width:100px" %)Lights green\|Relay #1 is closed
	168	\|(% style="width:100px" %)Off\|Relay #1 is opened
11.2	169
13.1	170	=== DS8 – relay 2 indicator ===
11.2	171
15.1	172	\|(% style="width:100px" %)State\|Description
	173	\|(% style="width:100px" %)Lights green\|Relay #2 is closed
	174	\|(% style="width:100px" %)Off\|Relay #2 is opened
11.2	175
13.1	176	=== DS5 – relay 3 indicator ===
11.2	177
15.1	178	\|(% style="width:100px" %)State\|Description
	179	\|(% style="width:100px" %)Lights green\|Relay #3 is closed
	180	\|(% style="width:100px" %)Off\|Relay #3 is opened
11.2	181
13.1	182	=== DS6 – relay 4 indicator ===
11.2	183
15.1	184	\|(% style="width:100px" %)State\|Description
	185	\|(% style="width:100px" %)Lights green\|Relay #4 is closed
	186	\|(% style="width:100px" %)Off\|Relay #4 is opened
11.2	187
5.3	188

Wiki source code of 2. Connection

Applications

Navigation

Table of Contents