Skip to Content
Last modified by Admin on 2025/07/15 17:33
From version 64.1
edited by Admin
on 2025/03/18 12:22
Change comment: There is no comment for this version
To version 25.3
edited by Admin
on 2024/11/20 11:04
Change comment: Update document after refactoring.

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -2. Installation and connection
1 +2. Connection procedure
Parent
... ... @@ -1,1 +1,1 @@
1 -Battery management systems.BMS Main 2\.1.WebHome
1 +drafts.bms-main-2-1.WebHome
Content
... ... @@ -1,36 +34,3 @@
1 -(% data-numbered-headings-start="2" style="--numbered-headings-start: 1;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 -= Installation and connection =
3 -
4 -== Safety rules ==
5 -
6 -To perform the protection functions, the BMS must be able to disconnect the battery from the load and charger. To do this, at least one contactor able to break the load and charge circuits must be connected to the BMS.
7 -
8 -Before use, **configure the system**. Proper operation of the BMS is possible only if it is correctly configured.
9 -
10 -(% class="box warningmessage" %)
11 -(((
12 -The BMS can be connected to batteries with life-threatening and health-hazardous voltage levels. When working with high-voltage batteries, observe electrical safety regulations, use safety glasses, protective clothing, insulated tools and appliances. To prevent the damage of device avoid electrostatic discharges while working with the battery.
13 -)))
14 -
15 -(% class="box errormessage" %)
16 -(((
17 -**The system is not designed to operate with batteries whose total voltage exceeds 1200 V.**
18 -)))
19 -
20 -== Installation procedure ==
21 -
22 -Overall and mounting dimensions of the BMS Main 2.1 are shown below.
23 -
24 -[[image:1732198397369-222.png||data-xwiki-image-style-alignment="center" height="393" width="556"]]
25 -
26 -(% style="width:494px" %)
27 -|**Parameter**|(% style="width:178px" %)**Value**
28 -|Overall dimensions (length × width × height), mm|(% style="width:178px" %)120 × 120 × 32
29 -|Mounting dimensions (length × width), mm|(% style="width:178px" %)114 × 114
30 -|Mounting holes|(% style="width:178px" %)M3
31 -
32 -== Connection procedure ==
33 -
34 34  The mounting area of the BMS Main 2.1 must be protected from mechanical particles (dust, dirt, large objects) and water. The installation site must provide convenient access for subsequent connection to the device’s headers.
35 35  
36 36  1. Connect the charging and discharging contactors to the P6-P9 headers.
... ... @@ -38,231 +38,215 @@
38 38  1. Connect the BMS Main 2.1 to the on-board CAN network. Observe the rules for connecting CAN devices. If the BMS Main 2.1 is the last device on a bus, close pins 1-2 on the P21 jumper, otherwise leave the jumper on pins 2-3.
39 39  1. Connect a power supply to the P1 header. It is not recommended to power the BMS Main 2.1 from the battery only, since at a critical discharge of the battery, it is not possible to turn on the BMS and close the charging contactor.
40 40  
41 -== ​​​​Headers description ==
8 += ​​​​Headers description =
42 42  
43 43  The BMS Main 2.1 headers are shown in figure below.
44 44  
45 -[[image:1731516393377-928.jpeg||alt="1731517946345-632.png" data-xwiki-image-style-alignment="center" height="417" width="451"]]
12 +[[The BMS Main 2.1 headers>>image:1731517946345-632.png||height="417" width="451"]]
46 46  
47 -(% class="box warningmessage" %)
48 -(((
49 -**Attention!**
50 -All headers are shown from the device side!
51 -)))
14 +(% class="wikigeneratedid" %)
15 +Following chapters describes the BMS Main 2.1 headers pinout.
52 52  
53 53  === P1 – header for power supply ===
54 54  
55 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
19 +[[image:1731516593096-166.png||height="80" width="42"]]
56 56  
57 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
21 +(% style="width:339px" %)
22 +|(% style="width:71px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:174px" %)**Description**
23 +|(% style="width:71px" %)**1**|(% style="width:91px" %)**GND**|(% style="width:174px" %)Ground
24 +|(% style="width:71px" %)**2**|(% style="width:91px" %)**V+**|(% style="width:174px" %)Supply voltage 9-30V
58 58  
59 -|**Pin**|**Name**|**Description**
60 -|**1**|**GND**|Ground
61 -|**2**|**V+**|Supply voltage 9-30V
62 -
63 63  === P15 – header for BMS Logic ===
64 64  
65 -Receptacle Housing: Molex 430250400. Terminals: Molex 43030
28 +[[image:1731516577472-301.png||height="77" width="71"]]
66 66  
67 -[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
30 +(% style="width:524px" %)
31 +|(% style="width:69px" %)**Pin**|(% style="width:97px" %)**Name**|(% style="width:355px" %)**Description**
32 +|(% style="width:69px" %)**1**|(% style="width:97px" %)**RS485_A**|(% style="width:355px" %)RS-485 line A for communication with BMS Logic
33 +|(% style="width:69px" %)**2**|(% style="width:97px" %)**RS485_B**|(% style="width:355px" %)RS-485 line B for communication with BMS Logic
34 +|(% style="width:69px" %)**3**|(% style="width:97px" %)**+5V**|(% style="width:355px" %)Supply voltage for BMS Logic
35 +|(% style="width:69px" %)**4**|(% style="width:97px" %)**GND**|(% style="width:355px" %)Ground
68 68  
69 -|**Pin**|**Name**|**Description**
70 -|**1**|**RS485_A**|RS-485 line A for communication with BMS Logic
71 -|**2**|**RS485_B**|RS-485 line B for communication with BMS Logic
72 -|**3**|**+5V**|Supply voltage for BMS Logic
73 -|**4**|**GND**|Ground
74 -
75 75  === P12 – header for current sensor ===
76 76  
77 -Receptacle Housing: Molex 430250400. Terminals: Molex 43030
39 +[[image:1731516685999-633.png||height="74" width="68"]]
78 78  
79 -[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
41 +(% style="width:531px" %)
42 +|(% style="width:75px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:360px" %)**Description**
43 +|(% style="width:75px" %)**1**|(% style="width:93px" %)**+5V**|(% style="width:360px" %)Supply voltage for the current sensor 5V, max 50 mA
44 +|(% style="width:75px" %)**2**|(% style="width:93px" %)**GND**|(% style="width:360px" %)Ground
45 +|(% style="width:75px" %)**3**|(% style="width:93px" %)**Vcs**|(% style="width:360px" %)ADC input (current sensor output)
46 +|(% style="width:75px" %)**4**|(% style="width:93px" %)**Vref**|(% style="width:360px" %)ADC input (current sensor reference signal)
80 80  
81 -|**Pin**|**Name**|**Description**
82 -|**1**|**+5V**|Supply voltage for the current sensor 5V, max 50 mA
83 -|**2**|**GND**|Ground
84 -|**3**|**Vcs**|ADC input (current sensor output)
85 -|**4**|**Vref**|ADC input (current sensor reference signal)
86 -
87 87  === P13 – header for humidity sensor ===
88 88  
89 -Receptacle Housing: Molex 430250400. Terminals: Molex 43030
50 +[[image:1731516942455-641.png||height="70" width="64"]]
90 90  
91 -[[image:1732198896526-660.png||data-xwiki-image-style-alignment="center" height="70" width="64"]]
52 +(% style="width:531px" %)
53 +|(% style="width:77px" %)**Pin**|(% style="width:92px" %)**Name**|(% style="width:359px" %)**Description**
54 +|(% style="width:77px" %)**1**|(% style="width:92px" %)**+5V**|(% style="width:359px" %)Supply voltage 5 V, max 50 mA
55 +|(% style="width:77px" %)**2**|(% style="width:92px" %)**GND**|(% style="width:359px" %)Ground
56 +|(% style="width:77px" %)**3**|(% style="width:92px" %)**Vhs**|(% style="width:359px" %)ADC input (humidity sensor output)
57 +|(% style="width:77px" %)**4**|(% style="width:92px" %)**Vts**|(% style="width:359px" %)ADC input (temperature sensor output)
92 92  
93 -|**Pin**|**Name**|**Description**
94 -|**1**|**+5V**|Supply voltage 5 V, max 50 mA
95 -|**2**|**GND**|Ground
96 -|**3**|**Vhs**|ADC input (humidity sensor output)
97 -|**4**|**Vts**|ADC input (temperature sensor output)
98 -
99 99  === P8 – header of relay 1 ===
100 100  
101 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
61 +[[image:1731517023208-641.png||height="80" width="42"]]
102 102  
103 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
104 -
105 105  By default, relay 1 is used to control the discharging contactor.
106 106  
107 -|**Pin**|**Name**|**Description**
108 -|**1**|**V+**|Switching voltage (up to 55V, max 3A)
109 -|**2**|**NO**|Normally open contact
65 +(% style="width:527px" %)
66 +|(% style="width:82px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:351px" %)**Description**
67 +|(% style="width:82px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:351px" %)Switching voltage (up to 55V, max 2A)
68 +|(% style="width:82px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:351px" %)Normally open contact
110 110  
111 -Contactor connection example for all relays:
112 -
113 -[[image:1741619814065-850.png||height="189" width="252"]]
114 -
115 115  === P9 – header of relay 2 ===
116 116  
117 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
72 +[[image:1731517025702-799.png||height="71" width="37"]]
118 118  
119 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
120 -
121 121  By default, relay 2 is used to output the “Allow charging” signal.
122 122  
123 -|**Pin**|**Name**|**Description**
124 -|**1**|**V+**|Switching voltage (up to 55V, max 3A)
125 -|**2**|**NO**|Normally open contact
76 +(% style="width:524px" %)
77 +|(% style="width:89px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:341px" %)**Description**
78 +|(% style="width:89px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:341px" %)Switching voltage (up to 55V, max 2A)
79 +|(% style="width:89px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:341px" %)Normally open contact
126 126  
127 -Contactor connection example: see relay 1.
128 -
129 129  === P6 – header of relay 3 ===
130 130  
131 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
83 +[[image:1731517025702-799.png||height="67" width="35"]]
132 132  
133 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
134 -
135 135  By default, relay 3 is used to control the charging contactor.
136 136  
137 -|**Pin**|**Name**|**Description**
138 -|**1**|**V+**|Switching voltage up to 55V,
139 -up to 8A (board rev. 2.1b), up to 3A (board rev. 2.1c)
140 -|**2**|**NO**|Normally open contact
87 +(% style="width:524px" %)
88 +|(% style="width:101px" %)**Pin**|(% style="width:88px" %)**Name**|(% style="width:332px" %)**Description**
89 +|(% style="width:101px" %)**1**|(% style="width:88px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
90 +|(% style="width:101px" %)**2**|(% style="width:88px" %)**NO**|(% style="width:332px" %)Normally open contact
141 141  
142 -Contactor connection example: see relay 1.
143 -
144 144  === P7 – header of relay 4 ===
145 145  
146 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
94 +[[image:1731517025702-799.png||height="65" width="34"]]
147 147  
148 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
149 -
150 150  By default, relay 4 is used to control the heater.
151 151  
152 -|**Pin**|**Name**|**Description**
153 -|**1**|**V+**|Switching voltage up to 55V,
154 -up to 8A (board rev. 2.1b), up to 3A (board rev. 2.1c)
155 -|**2**|**NO**|Normally open contact
98 +(% style="width:530px" %)
99 +|(% style="width:102px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:332px" %)**Description**
100 +|(% style="width:102px" %)**1**|(% style="width:93px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
101 +|(% style="width:102px" %)**2**|(% style="width:93px" %)**NO**|(% style="width:332px" %)Normally open contact
156 156  
157 -Contactor connection example: see relay 1.
158 -
159 159  === P14 – header for CAN and RS-485 interfaces ===
160 160  
161 -Receptacle Housing: Molex 430250600. Terminals: Molex 43030
105 +[[image:1731517180930-597.png||height="81" width="113"]]
162 162  
163 -[[image:1731517180930-597.png||data-xwiki-image-style-alignment="center" height="81" width="113"]]
164 -
165 165  (% style="width:641px" %)
166 -|**Pin**|**Name**|**Description**
167 -|**1**|**EXT_RS485_A**|RS-485 line A for communication with external equipment
168 -|**2**|**CAN_H**|CAN H line for communication with external equipment
169 -|**3**|**+5V_CAN**|Supply voltage 5V for external devices, max 200 mA
170 -|**4**|**EXT_RS485_B**|RS-485 line B for communication with external equipment
171 -|**5**|**CAN_L**|CAN L line for communication with external equipment
172 -|**6**|**GND_CAN**|Ground
108 +|(% style="width:107px" %)**Pin**|(% style="width:127px" %)**Name**|(% style="width:404px" %)**Description**
109 +|(% style="width:107px" %)**1**|(% style="width:127px" %)**EXT_RS485_A**|(% style="width:404px" %)RS-485 line A for communication with external equipment
110 +|(% style="width:107px" %)**2**|(% style="width:127px" %)**CAN_H**|(% style="width:404px" %)CAN H line for communication with external equipment
111 +|(% style="width:107px" %)**3**|(% style="width:127px" %)**+5V_CAN**|(% style="width:404px" %)Supply voltage 5V for external devices, max 200 mA
112 +|(% style="width:107px" %)**4**|(% style="width:127px" %)**EXT_RS485_B**|(% style="width:404px" %)RS-485 line B for communication with external equipment
113 +|(% style="width:107px" %)**5**|(% style="width:127px" %)**CAN_L**|(% style="width:404px" %)CAN L line for communication with external equipment
114 +|(% style="width:107px" %)**6**|(% style="width:127px" %)**GND_CAN**|(% style="width:404px" %)Ground
173 173  
174 174  === P21 – CAN termination resistor jumper ===
175 175  
176 -[[image:1731517188900-976.png||data-xwiki-image-style-alignment="center" height="78" width="149"]]
118 +[[image:1731517188900-976.png||height="78" width="149"]]
177 177  
178 178  To connect the termination resistor between the lines **CAN_H** and **CAN_L**, install a jumper, according to the P21 pinout:
179 179  
180 -|**Pin**|**Name**|**Description**
181 -|**1-2**|**120 Ohm**|Termination resistor 120 Ohm is connected
182 -|**2-3**|**-**|Termination resistor 120 Ohm is not connected
122 +(% style="width:643px" %)
123 +|**Pin**|(% style="width:122px" %)**Name**|(% style="width:400px" %)**Description**
124 +|**1-2**|(% style="width:122px" %)**120 Ohm**|(% style="width:400px" %)Termination resistor 120 Ohm is connected
125 +|**2-3**|(% style="width:122px" %)**-**|(% style="width:400px" %)Termination resistor 120 Ohm is not connected
183 183  
184 184  === P22 - RS-485 termination resistor jumper ===
185 185  
186 -[[image:1731517195672-298.png||data-xwiki-image-style-alignment="center" height="81" width="155"]]
129 +[[image:1731517195672-298.png||height="81" width="155"]]
187 187  
188 188  To connect the termination resistor between the **EXT_RS485_A** and **EXT_RS485_B** lines, install a jumper according to the P22 pinout:
189 189  
190 -|**Pin**|**Name**|**Description**
191 -|**1-2**|**120 Ohm**|Terminating resistor 120 Ohm is connected
192 -|**2-3**|**-**|Terminating resistor 120 Ohm is not connected
133 +(% style="width:644px" %)
134 +|**Pin**|(% style="width:121px" %)**Name**|(% style="width:402px" %)**Description**
135 +|**1-2**|(% style="width:121px" %)**120 Ohm**|(% style="width:402px" %)Terminating resistor 120 Ohm is connected
136 +|**2-3**|(% style="width:121px" %)**-**|(% style="width:402px" %)Terminating resistor 120 Ohm is not connected
193 193  
194 194  === P11 – header for discrete inputs/outputs ===
195 195  
196 -Receptacle Housing: Molex 430251600. Terminals: Molex 43030
140 +[[image:1731517206246-979.png||height="81" width="258"]]
197 197  
198 -[[image:1732198937514-731.png||data-xwiki-image-style-alignment="center" height="85" width="272"]]
142 +(% style="width:584px" %)
143 +|(% style="width:98px" %)**Pin**|(% style="width:157px" %)**Name**|(% style="width:326px" %)**Description**
144 +|(% style="width:98px" %)**16**|(% style="width:157px" %)**IN_1**|(% style="width:326px" %)Discrete input #1 “dry contact” (+5V)
145 +|(% style="width:98px" %)**8**|(% style="width:157px" %)**GND_1**|(% style="width:326px" %)Discrete input #1 “dry contact” (ground)
146 +|(% style="width:98px" %)**15**|(% style="width:157px" %)**IN_2**|(% style="width:326px" %)Discrete input #2 “dry contact” (+5V)
147 +|(% style="width:98px" %)**7**|(% style="width:157px" %)**GND_2**|(% style="width:326px" %)Discrete input #2 “dry contact” (ground)
148 +|(% style="width:98px" %)**14**|(% style="width:157px" %)**IN_3**|(% style="width:326px" %)Discrete input #3 “dry contact” (+5V)
149 +|(% style="width:98px" %)**6**|(% style="width:157px" %)**GND_3**|(% style="width:326px" %)Discrete input #3 “dry contact” (ground)
150 +|(% style="width:98px" %)**13**|(% style="width:157px" %)**IN_4**|(% style="width:326px" %)Discrete input #4 “dry contact” (+5V)
151 +|(% style="width:98px" %)**5**|(% style="width:157px" %)**GND_4**|(% style="width:326px" %)Discrete input #4 “dry contact” (ground)
152 +|(% style="width:98px" %)**12**|(% style="width:157px" %)**OUT_4**|(% style="width:326px" %)Discrete output #4 (+5V, 20mA)
153 +|(% style="width:98px" %)**4**|(% style="width:157px" %)**GND_OUT_4**|(% style="width:326px" %)Discrete output #4 (ground)
154 +|(% style="width:98px" %)**11**|(% style="width:157px" %)**OUT_3**|(% style="width:326px" %)Discrete output #3 (+5V, 20mA)
155 +|(% style="width:98px" %)**3**|(% style="width:157px" %)**GND_OUT_3**|(% style="width:326px" %)Discrete output #3 (ground)
156 +|(% style="width:98px" %)**10**|(% style="width:157px" %)**OUT_2**|(% style="width:326px" %)Discrete output #2 (+5V, 20mA)
157 +|(% style="width:98px" %)**2**|(% style="width:157px" %)**GND_OUT_2**|(% style="width:326px" %)Discrete output #2 (ground)
158 +|(% style="width:98px" %)**9**|(% style="width:157px" %)**OUT_1**|(% style="width:326px" %)Discrete output #1 (+5V, 20mA)
159 +|(% style="width:98px" %)**1**|(% style="width:157px" %)**GND_OUT_1**|(% style="width:326px" %)Discrete output #1 (ground)
199 199  
200 -|**Pin**|**Name**|**Description**
201 -|**16**|**IN_1**|Discrete input #1 “dry contact” (+5V)
202 -|**8**|**GND_1**|Discrete input #1 “dry contact” (ground)
203 -|**15**|**IN_2**|Discrete input #2 “dry contact” (+5V)
204 -|**7**|**GND_2**|Discrete input #2 “dry contact” (ground)
205 -|**14**|**IN_3**|Discrete input #3 “dry contact” (+5V)
206 -|**6**|**GND_3**|Discrete input #3 “dry contact” (ground)
207 -|**13**|**IN_4**|Discrete input #4 “dry contact” (+5V)
208 -|**5**|**GND_4**|Discrete input #4 “dry contact” (ground)
209 -|**12**|**OUT_4**|Discrete output #4 (+5V, 20mA)
210 -|**4**|**GND_OUT_4**|Discrete output #4 (ground)
211 -|**11**|**OUT_3**|Discrete output #3 (+5V, 20mA)
212 -|**3**|**GND_OUT_3**|Discrete output #3 (ground)
213 -|**10**|**OUT_2**|Discrete output #2 (+5V, 20mA)
214 -|**2**|**GND_OUT_2**|Discrete output #2 (ground)
215 -|**9**|**OUT_1**|Discrete output #1 (+5V, 20mA)
216 -|**1**|**GND_OUT_1**|Discrete output #1 (ground)
161 += Indicators =
217 217  
218 -== Indicators ==
219 -
220 220  === DS1 – power indicator ===
221 221  
222 -|**State**|**Description**
223 -|**Lights red**|The device is powered
224 -|**Off**|The device is not powered
165 +(% style="width:442px" %)
166 +|(% style="width:138px" %)**State**|(% style="width:301px" %)**Description**
167 +|(% style="width:138px" %)**Lights red**|(% style="width:301px" %)The device is powered
168 +|(% style="width:138px" %)**Off**|(% style="width:301px" %)The device is not powered
225 225  
226 226  === DS2 – operation indicator ===
227 227  
228 -|**State**|**Description**
229 -|**Blinking green**|The BMS firmware is running
230 -|**Off**|The BMS firmware is not running
172 +(% style="width:442px" %)
173 +|(% style="width:137px" %)**State**|(% style="width:302px" %)**Description**
174 +|(% style="width:137px" %)**Blinking green**|(% style="width:302px" %)The BMS firmware is running
175 +|(% style="width:137px" %)**Off**|(% style="width:302px" %)The BMS firmware is not running
231 231  
232 232  === DS3 – communication indicator ===
233 233  
234 -|**State**|**Description**
235 -|**Blinking yellow (2Hz)**|Initializing communication with BMS Logic boards
236 -|**Blinking yellow (25Hz)**|Communication with BMS Logic is established
179 +(% style="width:539px" %)
180 +|(% style="width:175px" %)**State**|(% style="width:361px" %)**Description**
181 +|(% style="width:175px" %)**Blinking yellow (2Hz)**|(% style="width:361px" %)Initializing communication with BMS Logic boards
182 +|(% style="width:175px" %)**Blinking yellow (25Hz)**|(% style="width:361px" %)Communication with BMS Logic is established
237 237  
238 238  === DS4 – error indicator ===
239 239  
186 +(% style="width:539px" %)
187 +|(% style="width:176px" %)**State**|(% style="width:360px" %)**Description**
188 +|(% style="width:176px" %)**Blinking red**|(% style="width:360px" %)Errors in communication with BMS Logic
240 240  
241 -|(**State**|**Description**
242 -|(**Blinking red**|Errors in communication with BMS Logic
243 -
244 244  === DS7 – relay 1 indicator ===
245 245  
246 -|**State**|**Description**
247 -|**Lights green**|Relay #1 is closed
248 -|**Off**|Relay #1 is opened
192 +(% style="width:541px" %)
193 +|(% style="width:179px" %)**State**|(% style="width:359px" %)**Description**
194 +|(% style="width:179px" %)**Lights green**|(% style="width:359px" %)Relay #1 is closed
195 +|(% style="width:179px" %)**Off**|(% style="width:359px" %)Relay #1 is opened
249 249  
250 250  === DS8 – relay 2 indicator ===
251 251  
252 -|**State**|**Description**
253 -|**Lights green**|Relay #2 is closed
254 -|**Off**|Relay #2 is opened
255 255  
200 +(% style="width:542px" %)
201 +|(% style="width:180px" %)**State**|(% style="width:359px" %)**Description**
202 +|(% style="width:180px" %)**Lights green**|(% style="width:359px" %)Relay #2 is closed
203 +|(% style="width:180px" %)**Off**|(% style="width:359px" %)Relay #2 is opened
204 +
256 256  === DS5 – relay 3 indicator ===
257 257  
258 -|**State**|**Description**
259 -|**Lights green**|Relay #3 is closed
260 -|**Off**|Relay #3 is opened
207 +(% style="width:542px" %)
208 +|(% style="width:183px" %)**State**|(% style="width:356px" %)**Description**
209 +|(% style="width:183px" %)**Lights green**|(% style="width:356px" %)Relay #3 is closed
210 +|(% style="width:183px" %)**Off**|(% style="width:356px" %)Relay #3 is opened
261 261  
262 262  === DS6 – relay 4 indicator ===
263 263  
264 -|**State**|**Description**
265 -|**Lights green**|Relay #4 is closed
266 -|**Off**|Relay #4 is opened
214 +(% style="width:542px" %)
215 +|(% style="width:187px" %)**State**|(% style="width:352px" %)**Description**
216 +|(% style="width:187px" %)**Lights green**|(% style="width:352px" %)Relay #4 is closed
217 +|(% style="width:187px" %)**Off**|(% style="width:352px" %)Relay #4 is opened
267 267  
268 268  
1732198397369-222.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -81.3 KB
Content
1732198827034-560.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.1 KB
Content
1732198890482-787.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -2.0 KB
Content
1732198896526-660.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -2.0 KB
Content
1732198937514-731.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -7.1 KB
Content
1741619628288-759.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -29.2 KB
Content
1741619637854-961.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -29.2 KB
Content
1741619700532-367.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -14.1 KB
Content
1741619814065-850.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -15.1 KB
Content
1741620022836-867.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -13.3 KB
Content
1731516474613-418.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1731516577472-301.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1731516593096-166.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1731516685999-633.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1731516942455-641.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1731517023208-641.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1731517025702-799.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1731517206246-979.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1731517946345-632.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content