Skip to Content
Last modified by Admin on 2025/07/15 17:33
From version 63.1
edited by Admin
on 2025/03/18 12:17
Change comment: There is no comment for this version
To version 25.1
edited by Admin
on 2024/11/19 13:21
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -2. Installation and connection
1 +2. Connection procedure
Parent
... ... @@ -1,1 +1,1 @@
1 -Battery management systems.BMS Main 2\.1.WebHome
1 +Controllers.bms-main-2-1.WebHome
Content
... ... @@ -1,38 +36,3 @@
1 -(% data-numbered-headings-start="2" style="--numbered-headings-start: 1;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 -= Installation and connection =
3 -
4 -== Safety rules ==
5 -
6 -To perform the protection functions, the BMS must be able to disconnect the battery from the load and charger. To do this, at least one contactor able to break the load and charge circuits must be connected to the BMS.
7 -
8 -Before use, **configure the system**. Proper operation of the BMS is possible only if it is correctly configured.
9 -
10 -It is not recommended to use the system in batteries formed by several series of cells connected in parallel. To increase capacity, it is recommended to connect several cells in parallel groups, and then connect the groups in series.
11 -
12 -(% class="box warningmessage" %)
13 -(((
14 -The BMS can be connected to batteries with life-threatening and health-hazardous voltage levels. When working with high-voltage batteries, observe electrical safety regulations, use safety glasses, protective clothing, insulated tools and appliances. To prevent the damage of device avoid electrostatic discharges while working with the battery.
15 -)))
16 -
17 -(% class="box errormessage" %)
18 -(((
19 -**The system is not designed to operate with batteries whose total voltage exceeds 1200 V.**
20 -)))
21 -
22 -== Installation procedure ==
23 -
24 -Overall and mounting dimensions of the BMS Main 2.1 are shown below.
25 -
26 -[[image:1732198397369-222.png||data-xwiki-image-style-alignment="center" height="393" width="556"]]
27 -
28 -(% style="width:494px" %)
29 -|**Parameter**|(% style="width:178px" %)**Value**
30 -|Overall dimensions (length × width × height), mm|(% style="width:178px" %)120 × 120 × 32
31 -|Mounting dimensions (length × width), mm|(% style="width:178px" %)114 × 114
32 -|Mounting holes|(% style="width:178px" %)M3
33 -
34 -== Connection procedure ==
35 -
36 36  The mounting area of the BMS Main 2.1 must be protected from mechanical particles (dust, dirt, large objects) and water. The installation site must provide convenient access for subsequent connection to the device’s headers.
37 37  
38 38  1. Connect the charging and discharging contactors to the P6-P9 headers.
... ... @@ -40,231 +40,215 @@
40 40  1. Connect the BMS Main 2.1 to the on-board CAN network. Observe the rules for connecting CAN devices. If the BMS Main 2.1 is the last device on a bus, close pins 1-2 on the P21 jumper, otherwise leave the jumper on pins 2-3.
41 41  1. Connect a power supply to the P1 header. It is not recommended to power the BMS Main 2.1 from the battery only, since at a critical discharge of the battery, it is not possible to turn on the BMS and close the charging contactor.
42 42  
43 -== ​​​​Headers description ==
8 += ​​​​Headers description =
44 44  
45 45  The BMS Main 2.1 headers are shown in figure below.
46 46  
47 -[[image:1731516393377-928.jpeg||alt="1731517946345-632.png" data-xwiki-image-style-alignment="center" height="417" width="451"]]
12 +[[The BMS Main 2.1 headers>>image:1731517946345-632.png||height="417" width="451"]]
48 48  
49 -(% class="box warningmessage" %)
50 -(((
51 -**Attention!**
52 -All headers are shown from the device side!
53 -)))
14 +(% class="wikigeneratedid" %)
15 +Following chapters describes the BMS Main 2.1 headers pinout.
54 54  
55 55  === P1 – header for power supply ===
56 56  
57 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
19 +[[image:1731516593096-166.png||height="80" width="42"]]
58 58  
59 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
21 +(% style="width:339px" %)
22 +|(% style="width:71px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:174px" %)**Description**
23 +|(% style="width:71px" %)**1**|(% style="width:91px" %)**GND**|(% style="width:174px" %)Ground
24 +|(% style="width:71px" %)**2**|(% style="width:91px" %)**V+**|(% style="width:174px" %)Supply voltage 9-30V
60 60  
61 -|**Pin**|**Name**|**Description**
62 -|**1**|**GND**|Ground
63 -|**2**|**V+**|Supply voltage 9-30V
64 -
65 65  === P15 – header for BMS Logic ===
66 66  
67 -Receptacle Housing: Molex 430250400. Terminals: Molex 43030
28 +[[image:1731516577472-301.png||height="77" width="71"]]
68 68  
69 -[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
30 +(% style="width:524px" %)
31 +|(% style="width:69px" %)**Pin**|(% style="width:97px" %)**Name**|(% style="width:355px" %)**Description**
32 +|(% style="width:69px" %)**1**|(% style="width:97px" %)**RS485_A**|(% style="width:355px" %)RS-485 line A for communication with BMS Logic
33 +|(% style="width:69px" %)**2**|(% style="width:97px" %)**RS485_B**|(% style="width:355px" %)RS-485 line B for communication with BMS Logic
34 +|(% style="width:69px" %)**3**|(% style="width:97px" %)**+5V**|(% style="width:355px" %)Supply voltage for BMS Logic
35 +|(% style="width:69px" %)**4**|(% style="width:97px" %)**GND**|(% style="width:355px" %)Ground
70 70  
71 -|**Pin**|**Name**|**Description**
72 -|**1**|**RS485_A**|RS-485 line A for communication with BMS Logic
73 -|**2**|**RS485_B**|RS-485 line B for communication with BMS Logic
74 -|**3**|**+5V**|Supply voltage for BMS Logic
75 -|**4**|**GND**|Ground
76 -
77 77  === P12 – header for current sensor ===
78 78  
79 -Receptacle Housing: Molex 430250400. Terminals: Molex 43030
39 +[[image:1731516685999-633.png||height="74" width="68"]]
80 80  
81 -[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
41 +(% style="width:531px" %)
42 +|(% style="width:75px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:360px" %)**Description**
43 +|(% style="width:75px" %)**1**|(% style="width:93px" %)**+5V**|(% style="width:360px" %)Supply voltage for the current sensor 5V, max 50 mA
44 +|(% style="width:75px" %)**2**|(% style="width:93px" %)**GND**|(% style="width:360px" %)Ground
45 +|(% style="width:75px" %)**3**|(% style="width:93px" %)**Vcs**|(% style="width:360px" %)ADC input (current sensor output)
46 +|(% style="width:75px" %)**4**|(% style="width:93px" %)**Vref**|(% style="width:360px" %)ADC input (current sensor reference signal)
82 82  
83 -|**Pin**|**Name**|**Description**
84 -|**1**|**+5V**|Supply voltage for the current sensor 5V, max 50 mA
85 -|**2**|**GND**|Ground
86 -|**3**|**Vcs**|ADC input (current sensor output)
87 -|**4**|**Vref**|ADC input (current sensor reference signal)
88 -
89 89  === P13 – header for humidity sensor ===
90 90  
91 -Receptacle Housing: Molex 430250400. Terminals: Molex 43030
50 +[[image:1731516942455-641.png||height="70" width="64"]]
92 92  
93 -[[image:1732198896526-660.png||data-xwiki-image-style-alignment="center" height="70" width="64"]]
52 +(% style="width:531px" %)
53 +|(% style="width:77px" %)**Pin**|(% style="width:92px" %)**Name**|(% style="width:359px" %)**Description**
54 +|(% style="width:77px" %)**1**|(% style="width:92px" %)**+5V**|(% style="width:359px" %)Supply voltage 5 V, max 50 mA
55 +|(% style="width:77px" %)**2**|(% style="width:92px" %)**GND**|(% style="width:359px" %)Ground
56 +|(% style="width:77px" %)**3**|(% style="width:92px" %)**Vhs**|(% style="width:359px" %)ADC input (humidity sensor output)
57 +|(% style="width:77px" %)**4**|(% style="width:92px" %)**Vts**|(% style="width:359px" %)ADC input (temperature sensor output)
94 94  
95 -|**Pin**|**Name**|**Description**
96 -|**1**|**+5V**|Supply voltage 5 V, max 50 mA
97 -|**2**|**GND**|Ground
98 -|**3**|**Vhs**|ADC input (humidity sensor output)
99 -|**4**|**Vts**|ADC input (temperature sensor output)
100 -
101 101  === P8 – header of relay 1 ===
102 102  
103 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
61 +[[image:1731517023208-641.png||height="80" width="42"]]
104 104  
105 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
106 -
107 107  By default, relay 1 is used to control the discharging contactor.
108 108  
109 -|**Pin**|**Name**|**Description**
110 -|**1**|**V+**|Switching voltage (up to 55V, max 3A)
111 -|**2**|**NO**|Normally open contact
65 +(% style="width:527px" %)
66 +|(% style="width:82px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:351px" %)**Description**
67 +|(% style="width:82px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:351px" %)Switching voltage (up to 55V, max 2A)
68 +|(% style="width:82px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:351px" %)Normally open contact
112 112  
113 -Contactor connection example for all relays:
114 -
115 -[[image:1741619814065-850.png||height="189" width="252"]]
116 -
117 117  === P9 – header of relay 2 ===
118 118  
119 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
72 +[[image:1731517025702-799.png||height="71" width="37"]]
120 120  
121 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
122 -
123 123  By default, relay 2 is used to output the “Allow charging” signal.
124 124  
125 -|**Pin**|**Name**|**Description**
126 -|**1**|**V+**|Switching voltage (up to 55V, max 3A)
127 -|**2**|**NO**|Normally open contact
76 +(% style="width:524px" %)
77 +|(% style="width:89px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:341px" %)**Description**
78 +|(% style="width:89px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:341px" %)Switching voltage (up to 55V, max 2A)
79 +|(% style="width:89px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:341px" %)Normally open contact
128 128  
129 -Contactor connection example: see relay 1.
130 -
131 131  === P6 – header of relay 3 ===
132 132  
133 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
83 +[[image:1731517025702-799.png||height="67" width="35"]]
134 134  
135 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
136 -
137 137  By default, relay 3 is used to control the charging contactor.
138 138  
139 -|**Pin**|**Name**|**Description**
140 -|**1**|**V+**|Switching voltage up to 55V,
141 -up to 8A (board rev. 2.1b), up to 3A (board rev. 2.1c)
142 -|**2**|**NO**|Normally open contact
87 +(% style="width:524px" %)
88 +|(% style="width:101px" %)**Pin**|(% style="width:88px" %)**Name**|(% style="width:332px" %)**Description**
89 +|(% style="width:101px" %)**1**|(% style="width:88px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
90 +|(% style="width:101px" %)**2**|(% style="width:88px" %)**NO**|(% style="width:332px" %)Normally open contact
143 143  
144 -Contactor connection example: see relay 1.
145 -
146 146  === P7 – header of relay 4 ===
147 147  
148 -Receptacle Housing: Molex 39012020. Terminals: Molex 5556
94 +[[image:1731517025702-799.png||height="65" width="34"]]
149 149  
150 -[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
151 -
152 152  By default, relay 4 is used to control the heater.
153 153  
154 -|**Pin**|**Name**|**Description**
155 -|**1**|**V+**|Switching voltage up to 55V,
156 -up to 8A (board rev. 2.1b), up to 3A (board rev. 2.1c)
157 -|**2**|**NO**|Normally open contact
98 +(% style="width:530px" %)
99 +|(% style="width:102px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:332px" %)**Description**
100 +|(% style="width:102px" %)**1**|(% style="width:93px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
101 +|(% style="width:102px" %)**2**|(% style="width:93px" %)**NO**|(% style="width:332px" %)Normally open contact
158 158  
159 -Contactor connection example: see relay 1.
160 -
161 161  === P14 – header for CAN and RS-485 interfaces ===
162 162  
163 -Receptacle Housing: Molex 430250600. Terminals: Molex 43030
105 +[[image:1731517180930-597.png||height="81" width="113"]]
164 164  
165 -[[image:1731517180930-597.png||data-xwiki-image-style-alignment="center" height="81" width="113"]]
166 -
167 167  (% style="width:641px" %)
168 -|**Pin**|**Name**|**Description**
169 -|**1**|**EXT_RS485_A**|RS-485 line A for communication with external equipment
170 -|**2**|**CAN_H**|CAN H line for communication with external equipment
171 -|**3**|**+5V_CAN**|Supply voltage 5V for external devices, max 200 mA
172 -|**4**|**EXT_RS485_B**|RS-485 line B for communication with external equipment
173 -|**5**|**CAN_L**|CAN L line for communication with external equipment
174 -|**6**|**GND_CAN**|Ground
108 +|(% style="width:107px" %)**Pin**|(% style="width:127px" %)**Name**|(% style="width:404px" %)**Description**
109 +|(% style="width:107px" %)**1**|(% style="width:127px" %)**EXT_RS485_A**|(% style="width:404px" %)RS-485 line A for communication with external equipment
110 +|(% style="width:107px" %)**2**|(% style="width:127px" %)**CAN_H**|(% style="width:404px" %)CAN H line for communication with external equipment
111 +|(% style="width:107px" %)**3**|(% style="width:127px" %)**+5V_CAN**|(% style="width:404px" %)Supply voltage 5V for external devices, max 200 mA
112 +|(% style="width:107px" %)**4**|(% style="width:127px" %)**EXT_RS485_B**|(% style="width:404px" %)RS-485 line B for communication with external equipment
113 +|(% style="width:107px" %)**5**|(% style="width:127px" %)**CAN_L**|(% style="width:404px" %)CAN L line for communication with external equipment
114 +|(% style="width:107px" %)**6**|(% style="width:127px" %)**GND_CAN**|(% style="width:404px" %)Ground
175 175  
176 176  === P21 – CAN termination resistor jumper ===
177 177  
178 -[[image:1731517188900-976.png||data-xwiki-image-style-alignment="center" height="78" width="149"]]
118 +[[image:1731517188900-976.png||height="78" width="149"]]
179 179  
180 180  To connect the termination resistor between the lines **CAN_H** and **CAN_L**, install a jumper, according to the P21 pinout:
181 181  
182 -|**Pin**|**Name**|**Description**
183 -|**1-2**|**120 Ohm**|Termination resistor 120 Ohm is connected
184 -|**2-3**|**-**|Termination resistor 120 Ohm is not connected
122 +(% style="width:643px" %)
123 +|**Pin**|(% style="width:122px" %)**Name**|(% style="width:400px" %)**Description**
124 +|**1-2**|(% style="width:122px" %)**120 Ohm**|(% style="width:400px" %)Termination resistor 120 Ohm is connected
125 +|**2-3**|(% style="width:122px" %)**-**|(% style="width:400px" %)Termination resistor 120 Ohm is not connected
185 185  
186 186  === P22 - RS-485 termination resistor jumper ===
187 187  
188 -[[image:1731517195672-298.png||data-xwiki-image-style-alignment="center" height="81" width="155"]]
129 +[[image:1731517195672-298.png||height="81" width="155"]]
189 189  
190 190  To connect the termination resistor between the **EXT_RS485_A** and **EXT_RS485_B** lines, install a jumper according to the P22 pinout:
191 191  
192 -|**Pin**|**Name**|**Description**
193 -|**1-2**|**120 Ohm**|Terminating resistor 120 Ohm is connected
194 -|**2-3**|**-**|Terminating resistor 120 Ohm is not connected
133 +(% style="width:644px" %)
134 +|**Pin**|(% style="width:121px" %)**Name**|(% style="width:402px" %)**Description**
135 +|**1-2**|(% style="width:121px" %)**120 Ohm**|(% style="width:402px" %)Terminating resistor 120 Ohm is connected
136 +|**2-3**|(% style="width:121px" %)**-**|(% style="width:402px" %)Terminating resistor 120 Ohm is not connected
195 195  
196 196  === P11 – header for discrete inputs/outputs ===
197 197  
198 -Receptacle Housing: Molex 430251600. Terminals: Molex 43030
140 +[[image:1731517206246-979.png||height="81" width="258"]]
199 199  
200 -[[image:1732198937514-731.png||data-xwiki-image-style-alignment="center" height="85" width="272"]]
142 +(% style="width:584px" %)
143 +|(% style="width:98px" %)**Pin**|(% style="width:157px" %)**Name**|(% style="width:326px" %)**Description**
144 +|(% style="width:98px" %)**16**|(% style="width:157px" %)**IN_1**|(% style="width:326px" %)Discrete input #1 “dry contact” (+5V)
145 +|(% style="width:98px" %)**8**|(% style="width:157px" %)**GND_1**|(% style="width:326px" %)Discrete input #1 “dry contact” (ground)
146 +|(% style="width:98px" %)**15**|(% style="width:157px" %)**IN_2**|(% style="width:326px" %)Discrete input #2 “dry contact” (+5V)
147 +|(% style="width:98px" %)**7**|(% style="width:157px" %)**GND_2**|(% style="width:326px" %)Discrete input #2 “dry contact” (ground)
148 +|(% style="width:98px" %)**14**|(% style="width:157px" %)**IN_3**|(% style="width:326px" %)Discrete input #3 “dry contact” (+5V)
149 +|(% style="width:98px" %)**6**|(% style="width:157px" %)**GND_3**|(% style="width:326px" %)Discrete input #3 “dry contact” (ground)
150 +|(% style="width:98px" %)**13**|(% style="width:157px" %)**IN_4**|(% style="width:326px" %)Discrete input #4 “dry contact” (+5V)
151 +|(% style="width:98px" %)**5**|(% style="width:157px" %)**GND_4**|(% style="width:326px" %)Discrete input #4 “dry contact” (ground)
152 +|(% style="width:98px" %)**12**|(% style="width:157px" %)**OUT_4**|(% style="width:326px" %)Discrete output #4 (+5V, 20mA)
153 +|(% style="width:98px" %)**4**|(% style="width:157px" %)**GND_OUT_4**|(% style="width:326px" %)Discrete output #4 (ground)
154 +|(% style="width:98px" %)**11**|(% style="width:157px" %)**OUT_3**|(% style="width:326px" %)Discrete output #3 (+5V, 20mA)
155 +|(% style="width:98px" %)**3**|(% style="width:157px" %)**GND_OUT_3**|(% style="width:326px" %)Discrete output #3 (ground)
156 +|(% style="width:98px" %)**10**|(% style="width:157px" %)**OUT_2**|(% style="width:326px" %)Discrete output #2 (+5V, 20mA)
157 +|(% style="width:98px" %)**2**|(% style="width:157px" %)**GND_OUT_2**|(% style="width:326px" %)Discrete output #2 (ground)
158 +|(% style="width:98px" %)**9**|(% style="width:157px" %)**OUT_1**|(% style="width:326px" %)Discrete output #1 (+5V, 20mA)
159 +|(% style="width:98px" %)**1**|(% style="width:157px" %)**GND_OUT_1**|(% style="width:326px" %)Discrete output #1 (ground)
201 201  
202 -|**Pin**|**Name**|**Description**
203 -|**16**|**IN_1**|Discrete input #1 “dry contact” (+5V)
204 -|**8**|**GND_1**|Discrete input #1 “dry contact” (ground)
205 -|**15**|**IN_2**|Discrete input #2 “dry contact” (+5V)
206 -|**7**|**GND_2**|Discrete input #2 “dry contact” (ground)
207 -|**14**|**IN_3**|Discrete input #3 “dry contact” (+5V)
208 -|**6**|**GND_3**|Discrete input #3 “dry contact” (ground)
209 -|**13**|**IN_4**|Discrete input #4 “dry contact” (+5V)
210 -|**5**|**GND_4**|Discrete input #4 “dry contact” (ground)
211 -|**12**|**OUT_4**|Discrete output #4 (+5V, 20mA)
212 -|**4**|**GND_OUT_4**|Discrete output #4 (ground)
213 -|**11**|**OUT_3**|Discrete output #3 (+5V, 20mA)
214 -|**3**|**GND_OUT_3**|Discrete output #3 (ground)
215 -|**10**|**OUT_2**|Discrete output #2 (+5V, 20mA)
216 -|**2**|**GND_OUT_2**|Discrete output #2 (ground)
217 -|**9**|**OUT_1**|Discrete output #1 (+5V, 20mA)
218 -|**1**|**GND_OUT_1**|Discrete output #1 (ground)
161 += Indicators =
219 219  
220 -== Indicators ==
221 -
222 222  === DS1 – power indicator ===
223 223  
224 -|**State**|**Description**
225 -|**Lights red**|The device is powered
226 -|**Off**|The device is not powered
165 +(% style="width:442px" %)
166 +|(% style="width:138px" %)**State**|(% style="width:301px" %)**Description**
167 +|(% style="width:138px" %)**Lights red**|(% style="width:301px" %)The device is powered
168 +|(% style="width:138px" %)**Off**|(% style="width:301px" %)The device is not powered
227 227  
228 228  === DS2 – operation indicator ===
229 229  
230 -|**State**|**Description**
231 -|**Blinking green**|The BMS firmware is running
232 -|**Off**|The BMS firmware is not running
172 +(% style="width:442px" %)
173 +|(% style="width:137px" %)**State**|(% style="width:302px" %)**Description**
174 +|(% style="width:137px" %)**Blinking green**|(% style="width:302px" %)The BMS firmware is running
175 +|(% style="width:137px" %)**Off**|(% style="width:302px" %)The BMS firmware is not running
233 233  
234 234  === DS3 – communication indicator ===
235 235  
236 -|**State**|**Description**
237 -|**Blinking yellow (2Hz)**|Initializing communication with BMS Logic boards
238 -|**Blinking yellow (25Hz)**|Communication with BMS Logic is established
179 +(% style="width:539px" %)
180 +|(% style="width:175px" %)**State**|(% style="width:361px" %)**Description**
181 +|(% style="width:175px" %)**Blinking yellow (2Hz)**|(% style="width:361px" %)Initializing communication with BMS Logic boards
182 +|(% style="width:175px" %)**Blinking yellow (25Hz)**|(% style="width:361px" %)Communication with BMS Logic is established
239 239  
240 240  === DS4 – error indicator ===
241 241  
186 +(% style="width:539px" %)
187 +|(% style="width:176px" %)**State**|(% style="width:360px" %)**Description**
188 +|(% style="width:176px" %)**Blinking red**|(% style="width:360px" %)Errors in communication with BMS Logic
242 242  
243 -|(**State**|**Description**
244 -|(**Blinking red**|Errors in communication with BMS Logic
245 -
246 246  === DS7 – relay 1 indicator ===
247 247  
248 -|**State**|**Description**
249 -|**Lights green**|Relay #1 is closed
250 -|**Off**|Relay #1 is opened
192 +(% style="width:541px" %)
193 +|(% style="width:179px" %)**State**|(% style="width:359px" %)**Description**
194 +|(% style="width:179px" %)**Lights green**|(% style="width:359px" %)Relay #1 is closed
195 +|(% style="width:179px" %)**Off**|(% style="width:359px" %)Relay #1 is opened
251 251  
252 252  === DS8 – relay 2 indicator ===
253 253  
254 -|**State**|**Description**
255 -|**Lights green**|Relay #2 is closed
256 -|**Off**|Relay #2 is opened
257 257  
200 +(% style="width:542px" %)
201 +|(% style="width:180px" %)**State**|(% style="width:359px" %)**Description**
202 +|(% style="width:180px" %)**Lights green**|(% style="width:359px" %)Relay #2 is closed
203 +|(% style="width:180px" %)**Off**|(% style="width:359px" %)Relay #2 is opened
204 +
258 258  === DS5 – relay 3 indicator ===
259 259  
260 -|**State**|**Description**
261 -|**Lights green**|Relay #3 is closed
262 -|**Off**|Relay #3 is opened
207 +(% style="width:542px" %)
208 +|(% style="width:183px" %)**State**|(% style="width:356px" %)**Description**
209 +|(% style="width:183px" %)**Lights green**|(% style="width:356px" %)Relay #3 is closed
210 +|(% style="width:183px" %)**Off**|(% style="width:356px" %)Relay #3 is opened
263 263  
264 264  === DS6 – relay 4 indicator ===
265 265  
266 -|**State**|**Description**
267 -|**Lights green**|Relay #4 is closed
268 -|**Off**|Relay #4 is opened
214 +(% style="width:542px" %)
215 +|(% style="width:187px" %)**State**|(% style="width:352px" %)**Description**
216 +|(% style="width:187px" %)**Lights green**|(% style="width:352px" %)Relay #4 is closed
217 +|(% style="width:187px" %)**Off**|(% style="width:352px" %)Relay #4 is opened
269 269  
270 270  
1732198397369-222.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -81.3 KB
Content
1732198827034-560.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.1 KB
Content
1732198890482-787.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -2.0 KB
Content
1732198896526-660.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -2.0 KB
Content
1732198937514-731.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -7.1 KB
Content
1741619628288-759.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -29.2 KB
Content
1741619637854-961.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -29.2 KB
Content
1741619700532-367.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -14.1 KB
Content
1741619814065-850.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -15.1 KB
Content
1741620022836-867.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -13.3 KB
Content
1731516474613-418.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +981 bytes
Content
1731516577472-301.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +1.5 KB
Content
1731516593096-166.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +981 bytes
Content
1731516685999-633.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +1.5 KB
Content
1731516942455-641.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +1.5 KB
Content
1731517023208-641.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +981 bytes
Content
1731517025702-799.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +981 bytes
Content
1731517206246-979.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +4.2 KB
Content
1731517946345-632.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +107.3 KB
Content