Skip to Content
Last modified by Admin on 2025/07/15 17:33
From version 6.2
edited by Admin
on 2024/11/13 16:56
Change comment: There is no comment for this version
To version 4.2
edited by Admin
on 2024/11/13 16:50
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -16,60 +16,7 @@
16 16  
17 17  [[image:1731516577472-301.png||data-xwiki-image-style-alignment="center" height="90" width="83"]]
18 18  
19 -|**Pin**|**Name**|**Description**
20 -|**1**|**RS485_A**|RS-485 line A for communication with BMS Logic
19 +|**1**|**RS485_A**|**RS-485 line A for communication with BMS Logic**
21 21  |**2**|**RS485_B**|RS-485 line B for communication with BMS Logic
22 22  |**3**|**+5V**|Supply voltage for BMS Logic
23 23  |**4**|**GND**|Ground
24 -
25 -== P12 – header for current sensor ==
26 -
27 -[[image:1731516685999-633.png||data-xwiki-image-style-alignment="center" height="98" width="90"]]
28 -
29 -|**Pin**|**Name**|**Description**
30 -|**1**|**+5V**|Supply voltage for the current sensor 5V, max 50 mA
31 -|**2**|**GND**|Ground
32 -|**3**|**Vcs**|ADC input (current sensor output)
33 -|**4**|**Vref**|ADC input (current sensor reference signal)
34 -
35 -== P13 – header for humidity sensor ==
36 -
37 -[[image:1731516942455-641.png||data-xwiki-image-style-alignment="center"]]
38 -
39 -|**Pin**|**Name**|**Description**
40 -|**1**|**+5V**|Supply voltage 5 V, max 50 mA
41 -|**2**|**GND**|Ground
42 -|**3**|**Vhs**|ADC input (humidity sensor output)
43 -|**4**|**Vts**|ADC input (temperature sensor output)
44 -
45 -
46 -1.
47 -11.
48 -111. P8 – header of relay 1
49 -
50 -[[image:file:///C:/Users/INASIB~~1/AppData/Local/Temp/msohtmlclip1/01/clip_image001.emz]]
51 -
52 -By default, relay 1 is used to control the discharging contactor.
53 -
54 -
55 -|**Pin**|**Name**|**Description**
56 -|**1**|**V+**|Switching voltage (up to 55V, max 2A)
57 -|**2**|**NO**|Normally open contact
58 -
59 -
60 -1.
61 -11.
62 -111. P9 – header of relay 2
63 -
64 -[[image:file:///C:/Users/INASIB~~1/AppData/Local/Temp/msohtmlclip1/01/clip_image001.emz]]
65 -
66 -By default, relay 2 is used to output the “Allow charging” signal.
67 -
68 -
69 -|**Pin**|**Name**|**Description**
70 -|**1**|**V+**|Switching voltage (up to 55V, max 2A)
71 -|**2**|**NO**|Normally open contact
72 -
73 -
74 -
75 -
1731516685999-633.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731516942455-641.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content