Skip to Content
Last modified by Admin on 2025/07/15 17:33
From version 26.2
edited by Admin
on 2024/11/21 14:13
Change comment: There is no comment for this version
To version 49.3
edited by Admin
on 2025/02/06 11:26
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -drafts.bms-main-2-1.WebHome
1 +Battery management systems.BMS Main 2\.1.WebHome
Content
... ... @@ -1,13 +1,21 @@
1 -== 2.1 Installation procedure ==
1 +(% data-numbered-headings-start="2" style="--numbered-headings-start: 1;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 += Installation and connection =
2 2  
3 -Overall and mounting dimensions of the BMS Main 2.1 are shown in Figure 29.
4 +== Installation procedure ==
4 4  
5 -[[Dimensions of the BMS Main 2.1>>image:1732198397369-222.png||data-xwiki-image-style-alignment="center" height="393" width="556"]]
6 +Overall and mounting dimensions of the BMS Main 2.1 are shown below.
6 6  
7 -== ==
8 +[[image:1732198397369-222.png||data-xwiki-image-style-alignment="center" height="393" width="556"]]
8 8  
9 -== 2.2 Connection procedure ==
10 +(% style="width:494px" %)
11 +|**Parameter**|(% style="width:178px" %)**Value**
12 +|Overall dimensions (length × width × height), mm|(% style="width:178px" %)120 × 120 × 32
13 +|Mounting dimensions (length × width), mm|(% style="width:178px" %)114 × 114
14 +|Mounting holes|(% style="width:178px" %)M3
15 +|Connectors type|(% style="width:178px" %)Molex MiniFit (P1, P6)
10 10  
17 +== Connection procedure ==
18 +
11 11  The mounting area of the BMS Main 2.1 must be protected from mechanical particles (dust, dirt, large objects) and water. The installation site must provide convenient access for subsequent connection to the device’s headers.
12 12  
13 13  1. Connect the charging and discharging contactors to the P6-P9 headers.
... ... @@ -15,214 +15,199 @@
15 15  1. Connect the BMS Main 2.1 to the on-board CAN network. Observe the rules for connecting CAN devices. If the BMS Main 2.1 is the last device on a bus, close pins 1-2 on the P21 jumper, otherwise leave the jumper on pins 2-3.
16 16  1. Connect a power supply to the P1 header. It is not recommended to power the BMS Main 2.1 from the battery only, since at a critical discharge of the battery, it is not possible to turn on the BMS and close the charging contactor.
17 17  
18 -== 2.2 ​​​​Headers description ==
26 +== ​​​​Headers description ==
19 19  
20 20  The BMS Main 2.1 headers are shown in figure below.
21 21  
22 -[[The BMS Main 2.1 headers>>image:1731517946345-632.png||height="417" width="451"]]
30 +[[image:1731516393377-928.jpeg||alt="1731517946345-632.png" data-xwiki-image-style-alignment="center" height="417" width="451"]]
23 23  
24 -(% class="wikigeneratedid" %)
25 -Following chapters describes the BMS Main 2.1 headers pinout.
32 +(% class="box warningmessage" %)
33 +(((
34 +**Attention!**
35 +All headers are shown from the device side!
36 +)))
26 26  
27 -=== 2.2.1 P1 – header for power supply ===
38 +=== P1 – header for power supply ===
28 28  
29 -[[image:1731516593096-166.png||height="80" width="42"]]
40 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
30 30  
31 -(% style="width:339px" %)
32 -|(% style="width:71px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:174px" %)**Description**
33 -|(% style="width:71px" %)**1**|(% style="width:91px" %)**GND**|(% style="width:174px" %)Ground
34 -|(% style="width:71px" %)**2**|(% style="width:91px" %)**V+**|(% style="width:174px" %)Supply voltage 9-30V
42 +|**Pin**|**Name**|**Description**
43 +|**1**|**GND**|Ground
44 +|**2**|**V+**|Supply voltage 9-30V
35 35  
36 -=== 2.2.2 P15 – header for BMS Logic ===
46 +=== P15 – header for BMS Logic ===
37 37  
38 -[[image:1731516577472-301.png||height="77" width="71"]]
48 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
39 39  
40 -(% style="width:524px" %)
41 -|(% style="width:69px" %)**Pin**|(% style="width:97px" %)**Name**|(% style="width:355px" %)**Description**
42 -|(% style="width:69px" %)**1**|(% style="width:97px" %)**RS485_A**|(% style="width:355px" %)RS-485 line A for communication with BMS Logic
43 -|(% style="width:69px" %)**2**|(% style="width:97px" %)**RS485_B**|(% style="width:355px" %)RS-485 line B for communication with BMS Logic
44 -|(% style="width:69px" %)**3**|(% style="width:97px" %)**+5V**|(% style="width:355px" %)Supply voltage for BMS Logic
45 -|(% style="width:69px" %)**4**|(% style="width:97px" %)**GND**|(% style="width:355px" %)Ground
50 +|**Pin**|**Name**|**Description**
51 +|**1**|**RS485_A**|RS-485 line A for communication with BMS Logic
52 +|**2**|**RS485_B**|RS-485 line B for communication with BMS Logic
53 +|**3**|**+5V**|Supply voltage for BMS Logic
54 +|**4**|**GND**|Ground
46 46  
47 -=== 2.2.3 P12 – header for current sensor ===
56 +=== P12 – header for current sensor ===
48 48  
49 -[[image:1731516685999-633.png||height="74" width="68"]]
58 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
50 50  
51 -(% style="width:531px" %)
52 -|(% style="width:75px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:360px" %)**Description**
53 -|(% style="width:75px" %)**1**|(% style="width:93px" %)**+5V**|(% style="width:360px" %)Supply voltage for the current sensor 5V, max 50 mA
54 -|(% style="width:75px" %)**2**|(% style="width:93px" %)**GND**|(% style="width:360px" %)Ground
55 -|(% style="width:75px" %)**3**|(% style="width:93px" %)**Vcs**|(% style="width:360px" %)ADC input (current sensor output)
56 -|(% style="width:75px" %)**4**|(% style="width:93px" %)**Vref**|(% style="width:360px" %)ADC input (current sensor reference signal)
60 +|**Pin**|**Name**|**Description**
61 +|**1**|**+5V**|Supply voltage for the current sensor 5V, max 50 mA
62 +|**2**|**GND**|Ground
63 +|**3**|**Vcs**|ADC input (current sensor output)
64 +|**4**|**Vref**|ADC input (current sensor reference signal)
57 57  
58 -=== 2.2.4 P13 – header for humidity sensor ===
66 +=== P13 – header for humidity sensor ===
59 59  
60 -[[image:1731516942455-641.png||height="70" width="64"]]
68 +[[image:1732198896526-660.png||data-xwiki-image-style-alignment="center" height="70" width="64"]]
61 61  
62 -(% style="width:531px" %)
63 -|(% style="width:77px" %)**Pin**|(% style="width:92px" %)**Name**|(% style="width:359px" %)**Description**
64 -|(% style="width:77px" %)**1**|(% style="width:92px" %)**+5V**|(% style="width:359px" %)Supply voltage 5 V, max 50 mA
65 -|(% style="width:77px" %)**2**|(% style="width:92px" %)**GND**|(% style="width:359px" %)Ground
66 -|(% style="width:77px" %)**3**|(% style="width:92px" %)**Vhs**|(% style="width:359px" %)ADC input (humidity sensor output)
67 -|(% style="width:77px" %)**4**|(% style="width:92px" %)**Vts**|(% style="width:359px" %)ADC input (temperature sensor output)
70 +|**Pin**|**Name**|**Description**
71 +|**1**|**+5V**|Supply voltage 5 V, max 50 mA
72 +|**2**|**GND**|Ground
73 +|**3**|**Vhs**|ADC input (humidity sensor output)
74 +|**4**|**Vts**|ADC input (temperature sensor output)
68 68  
69 -=== 2.2.5 P8 – header of relay 1 ===
76 +=== P8 – header of relay 1 ===
70 70  
71 -[[image:1731517023208-641.png||height="80" width="42"]]
78 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
72 72  
73 73  By default, relay 1 is used to control the discharging contactor.
74 74  
75 -(% style="width:527px" %)
76 -|(% style="width:82px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:351px" %)**Description**
77 -|(% style="width:82px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:351px" %)Switching voltage (up to 55V, max 2A)
78 -|(% style="width:82px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:351px" %)Normally open contact
82 +|**Pin**|**Name**|**Description**
83 +|**1**|**V+**|Switching voltage (up to 55V, max 2A)
84 +|**2**|**NO**|Normally open contact
79 79  
80 -=== 2.2.6 P9 – header of relay 2 ===
86 +=== P9 – header of relay 2 ===
81 81  
82 -[[image:1731517025702-799.png||height="71" width="37"]]
88 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
83 83  
84 84  By default, relay 2 is used to output the “Allow charging” signal.
85 85  
86 -(% style="width:524px" %)
87 -|(% style="width:89px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:341px" %)**Description**
88 -|(% style="width:89px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:341px" %)Switching voltage (up to 55V, max 2A)
89 -|(% style="width:89px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:341px" %)Normally open contact
92 +|**Pin**|**Name**|**Description**
93 +|**1**|**V+**|Switching voltage (up to 55V, max 2A)
94 +|**2**|**NO**|Normally open contact
90 90  
91 -=== 2.2.7 P6 – header of relay 3 ===
96 +=== P6 – header of relay 3 ===
92 92  
93 -[[image:1731517025702-799.png||height="67" width="35"]]
98 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
94 94  
95 95  By default, relay 3 is used to control the charging contactor.
96 96  
97 -(% style="width:524px" %)
98 -|(% style="width:101px" %)**Pin**|(% style="width:88px" %)**Name**|(% style="width:332px" %)**Description**
99 -|(% style="width:101px" %)**1**|(% style="width:88px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
100 -|(% style="width:101px" %)**2**|(% style="width:88px" %)**NO**|(% style="width:332px" %)Normally open contact
102 +|**Pin**|**Name**|**Description**
103 +|**1**|**V+**|Switching voltage (up to 55V, max 8A)
104 +|**2**|**NO**|Normally open contact
101 101  
102 -=== 2.2.8 P7 – header of relay 4 ===
106 +=== P7 – header of relay 4 ===
103 103  
104 -[[image:1731517025702-799.png||height="65" width="34"]]
108 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
105 105  
106 106  By default, relay 4 is used to control the heater.
107 107  
108 -(% style="width:530px" %)
109 -|(% style="width:102px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:332px" %)**Description**
110 -|(% style="width:102px" %)**1**|(% style="width:93px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
111 -|(% style="width:102px" %)**2**|(% style="width:93px" %)**NO**|(% style="width:332px" %)Normally open contact
112 +|**Pin**|**Name**|**Description**
113 +|**1**|**V+**|Switching voltage (up to 55V, max 8A)
114 +|**2**|**NO**|Normally open contact
112 112  
113 -=== 2.2.9 P14 – header for CAN and RS-485 interfaces ===
116 +=== P14 – header for CAN and RS-485 interfaces ===
114 114  
115 -[[image:1731517180930-597.png||height="81" width="113"]]
118 +[[image:1731517180930-597.png||data-xwiki-image-style-alignment="center" height="81" width="113"]]
116 116  
117 117  (% style="width:641px" %)
118 -|(% style="width:107px" %)**Pin**|(% style="width:127px" %)**Name**|(% style="width:404px" %)**Description**
119 -|(% style="width:107px" %)**1**|(% style="width:127px" %)**EXT_RS485_A**|(% style="width:404px" %)RS-485 line A for communication with external equipment
120 -|(% style="width:107px" %)**2**|(% style="width:127px" %)**CAN_H**|(% style="width:404px" %)CAN H line for communication with external equipment
121 -|(% style="width:107px" %)**3**|(% style="width:127px" %)**+5V_CAN**|(% style="width:404px" %)Supply voltage 5V for external devices, max 200 mA
122 -|(% style="width:107px" %)**4**|(% style="width:127px" %)**EXT_RS485_B**|(% style="width:404px" %)RS-485 line B for communication with external equipment
123 -|(% style="width:107px" %)**5**|(% style="width:127px" %)**CAN_L**|(% style="width:404px" %)CAN L line for communication with external equipment
124 -|(% style="width:107px" %)**6**|(% style="width:127px" %)**GND_CAN**|(% style="width:404px" %)Ground
121 +|**Pin**|**Name**|**Description**
122 +|**1**|**EXT_RS485_A**|RS-485 line A for communication with external equipment
123 +|**2**|**CAN_H**|CAN H line for communication with external equipment
124 +|**3**|**+5V_CAN**|Supply voltage 5V for external devices, max 200 mA
125 +|**4**|**EXT_RS485_B**|RS-485 line B for communication with external equipment
126 +|**5**|**CAN_L**|CAN L line for communication with external equipment
127 +|**6**|**GND_CAN**|Ground
125 125  
126 -=== 2.2.10 P21 – CAN termination resistor jumper ===
129 +=== P21 – CAN termination resistor jumper ===
127 127  
128 -[[image:1731517188900-976.png||height="78" width="149"]]
131 +[[image:1731517188900-976.png||data-xwiki-image-style-alignment="center" height="78" width="149"]]
129 129  
130 130  To connect the termination resistor between the lines **CAN_H** and **CAN_L**, install a jumper, according to the P21 pinout:
131 131  
132 -(% style="width:643px" %)
133 -|**Pin**|(% style="width:122px" %)**Name**|(% style="width:400px" %)**Description**
134 -|**1-2**|(% style="width:122px" %)**120 Ohm**|(% style="width:400px" %)Termination resistor 120 Ohm is connected
135 -|**2-3**|(% style="width:122px" %)**-**|(% style="width:400px" %)Termination resistor 120 Ohm is not connected
135 +|**Pin**|**Name**|**Description**
136 +|**1-2**|**120 Ohm**|Termination resistor 120 Ohm is connected
137 +|**2-3**|**-**|Termination resistor 120 Ohm is not connected
136 136  
137 -=== 2.2.11 P22 - RS-485 termination resistor jumper ===
139 +=== P22 - RS-485 termination resistor jumper ===
138 138  
139 -[[image:1731517195672-298.png||height="81" width="155"]]
141 +[[image:1731517195672-298.png||data-xwiki-image-style-alignment="center" height="81" width="155"]]
140 140  
141 141  To connect the termination resistor between the **EXT_RS485_A** and **EXT_RS485_B** lines, install a jumper according to the P22 pinout:
142 142  
143 -(% style="width:644px" %)
144 -|**Pin**|(% style="width:121px" %)**Name**|(% style="width:402px" %)**Description**
145 -|**1-2**|(% style="width:121px" %)**120 Ohm**|(% style="width:402px" %)Terminating resistor 120 Ohm is connected
146 -|**2-3**|(% style="width:121px" %)**-**|(% style="width:402px" %)Terminating resistor 120 Ohm is not connected
145 +|**Pin**|**Name**|**Description**
146 +|**1-2**|**120 Ohm**|Terminating resistor 120 Ohm is connected
147 +|**2-3**|**-**|Terminating resistor 120 Ohm is not connected
147 147  
148 -=== 2.2.12 P11 – header for discrete inputs/outputs ===
149 +=== P11 – header for discrete inputs/outputs ===
149 149  
150 -[[image:1731517206246-979.png||height="81" width="258"]]
151 +[[image:1732198937514-731.png||data-xwiki-image-style-alignment="center" height="85" width="272"]]
151 151  
152 -(% style="width:584px" %)
153 -|(% style="width:98px" %)**Pin**|(% style="width:157px" %)**Name**|(% style="width:326px" %)**Description**
154 -|(% style="width:98px" %)**16**|(% style="width:157px" %)**IN_1**|(% style="width:326px" %)Discrete input #1 “dry contact” (+5V)
155 -|(% style="width:98px" %)**8**|(% style="width:157px" %)**GND_1**|(% style="width:326px" %)Discrete input #1 “dry contact” (ground)
156 -|(% style="width:98px" %)**15**|(% style="width:157px" %)**IN_2**|(% style="width:326px" %)Discrete input #2 “dry contact” (+5V)
157 -|(% style="width:98px" %)**7**|(% style="width:157px" %)**GND_2**|(% style="width:326px" %)Discrete input #2 “dry contact” (ground)
158 -|(% style="width:98px" %)**14**|(% style="width:157px" %)**IN_3**|(% style="width:326px" %)Discrete input #3 “dry contact” (+5V)
159 -|(% style="width:98px" %)**6**|(% style="width:157px" %)**GND_3**|(% style="width:326px" %)Discrete input #3 “dry contact” (ground)
160 -|(% style="width:98px" %)**13**|(% style="width:157px" %)**IN_4**|(% style="width:326px" %)Discrete input #4 “dry contact” (+5V)
161 -|(% style="width:98px" %)**5**|(% style="width:157px" %)**GND_4**|(% style="width:326px" %)Discrete input #4 “dry contact” (ground)
162 -|(% style="width:98px" %)**12**|(% style="width:157px" %)**OUT_4**|(% style="width:326px" %)Discrete output #4 (+5V, 20mA)
163 -|(% style="width:98px" %)**4**|(% style="width:157px" %)**GND_OUT_4**|(% style="width:326px" %)Discrete output #4 (ground)
164 -|(% style="width:98px" %)**11**|(% style="width:157px" %)**OUT_3**|(% style="width:326px" %)Discrete output #3 (+5V, 20mA)
165 -|(% style="width:98px" %)**3**|(% style="width:157px" %)**GND_OUT_3**|(% style="width:326px" %)Discrete output #3 (ground)
166 -|(% style="width:98px" %)**10**|(% style="width:157px" %)**OUT_2**|(% style="width:326px" %)Discrete output #2 (+5V, 20mA)
167 -|(% style="width:98px" %)**2**|(% style="width:157px" %)**GND_OUT_2**|(% style="width:326px" %)Discrete output #2 (ground)
168 -|(% style="width:98px" %)**9**|(% style="width:157px" %)**OUT_1**|(% style="width:326px" %)Discrete output #1 (+5V, 20mA)
169 -|(% style="width:98px" %)**1**|(% style="width:157px" %)**GND_OUT_1**|(% style="width:326px" %)Discrete output #1 (ground)
153 +|**Pin**|**Name**|**Description**
154 +|**16**|**IN_1**|Discrete input #1 “dry contact” (+5V)
155 +|**8**|**GND_1**|Discrete input #1 “dry contact” (ground)
156 +|**15**|**IN_2**|Discrete input #2 “dry contact” (+5V)
157 +|**7**|**GND_2**|Discrete input #2 “dry contact” (ground)
158 +|**14**|**IN_3**|Discrete input #3 “dry contact” (+5V)
159 +|**6**|**GND_3**|Discrete input #3 “dry contact” (ground)
160 +|**13**|**IN_4**|Discrete input #4 “dry contact” (+5V)
161 +|**5**|**GND_4**|Discrete input #4 “dry contact” (ground)
162 +|**12**|**OUT_4**|Discrete output #4 (+5V, 20mA)
163 +|**4**|**GND_OUT_4**|Discrete output #4 (ground)
164 +|**11**|**OUT_3**|Discrete output #3 (+5V, 20mA)
165 +|**3**|**GND_OUT_3**|Discrete output #3 (ground)
166 +|**10**|**OUT_2**|Discrete output #2 (+5V, 20mA)
167 +|**2**|**GND_OUT_2**|Discrete output #2 (ground)
168 +|**9**|**OUT_1**|Discrete output #1 (+5V, 20mA)
169 +|**1**|**GND_OUT_1**|Discrete output #1 (ground)
170 170  
171 -= 2.3 Indicators =
171 +== Indicators ==
172 172  
173 -=== 2.3.1 DS1 – power indicator ===
173 +=== DS1 – power indicator ===
174 174  
175 -(% style="width:442px" %)
176 -|(% style="width:138px" %)**State**|(% style="width:301px" %)**Description**
177 -|(% style="width:138px" %)**Lights red**|(% style="width:301px" %)The device is powered
178 -|(% style="width:138px" %)**Off**|(% style="width:301px" %)The device is not powered
175 +|**State**|**Description**
176 +|**Lights red**|The device is powered
177 +|**Off**|The device is not powered
179 179  
180 -=== 2.3.2 DS2 – operation indicator ===
179 +=== DS2 – operation indicator ===
181 181  
182 -(% style="width:442px" %)
183 -|(% style="width:137px" %)**State**|(% style="width:302px" %)**Description**
184 -|(% style="width:137px" %)**Blinking green**|(% style="width:302px" %)The BMS firmware is running
185 -|(% style="width:137px" %)**Off**|(% style="width:302px" %)The BMS firmware is not running
181 +|**State**|**Description**
182 +|**Blinking green**|The BMS firmware is running
183 +|**Off**|The BMS firmware is not running
186 186  
187 -=== 2.3.3 DS3 – communication indicator ===
185 +=== DS3 – communication indicator ===
188 188  
189 -(% style="width:539px" %)
190 -|(% style="width:175px" %)**State**|(% style="width:361px" %)**Description**
191 -|(% style="width:175px" %)**Blinking yellow (2Hz)**|(% style="width:361px" %)Initializing communication with BMS Logic boards
192 -|(% style="width:175px" %)**Blinking yellow (25Hz)**|(% style="width:361px" %)Communication with BMS Logic is established
187 +|**State**|**Description**
188 +|**Blinking yellow (2Hz)**|Initializing communication with BMS Logic boards
189 +|**Blinking yellow (25Hz)**|Communication with BMS Logic is established
193 193  
194 -=== 2.3.4 DS4 – error indicator ===
191 +=== DS4 – error indicator ===
195 195  
196 -(% style="width:539px" %)
197 -|(% style="width:176px" %)**State**|(% style="width:360px" %)**Description**
198 -|(% style="width:176px" %)**Blinking red**|(% style="width:360px" %)Errors in communication with BMS Logic
199 199  
200 -=== 2.3.5 DS7 – relay 1 indicator ===
194 +|(**State**|**Description**
195 +|(**Blinking red**|Errors in communication with BMS Logic
201 201  
202 -(% style="width:541px" %)
203 -|(% style="width:179px" %)**State**|(% style="width:359px" %)**Description**
204 -|(% style="width:179px" %)**Lights green**|(% style="width:359px" %)Relay #1 is closed
205 -|(% style="width:179px" %)**Off**|(% style="width:359px" %)Relay #1 is opened
197 +=== DS7 – relay 1 indicator ===
206 206  
207 -=== 2.3.6 DS8 – relay 2 indicator ===
199 +|**State**|**Description**
200 +|**Lights green**|Relay #1 is closed
201 +|**Off**|Relay #1 is opened
208 208  
209 -(% style="width:542px" %)
210 -|(% style="width:180px" %)**State**|(% style="width:359px" %)**Description**
211 -|(% style="width:180px" %)**Lights green**|(% style="width:359px" %)Relay #2 is closed
212 -|(% style="width:180px" %)**Off**|(% style="width:359px" %)Relay #2 is opened
203 +=== DS8 – relay 2 indicator ===
213 213  
214 -=== 2.3.7 DS5 – relay 3 indicator ===
205 +|**State**|**Description**
206 +|**Lights green**|Relay #2 is closed
207 +|**Off**|Relay #2 is opened
215 215  
216 -(% style="width:542px" %)
217 -|(% style="width:183px" %)**State**|(% style="width:356px" %)**Description**
218 -|(% style="width:183px" %)**Lights green**|(% style="width:356px" %)Relay #3 is closed
219 -|(% style="width:183px" %)**Off**|(% style="width:356px" %)Relay #3 is opened
209 +=== DS5 – relay 3 indicator ===
220 220  
221 -=== 2.3.8 DS6 – relay 4 indicator ===
211 +|**State**|**Description**
212 +|**Lights green**|Relay #3 is closed
213 +|**Off**|Relay #3 is opened
222 222  
223 -(% style="width:542px" %)
224 -|(% style="width:187px" %)**State**|(% style="width:352px" %)**Description**
225 -|(% style="width:187px" %)**Lights green**|(% style="width:352px" %)Relay #4 is closed
226 -|(% style="width:187px" %)**Off**|(% style="width:352px" %)Relay #4 is opened
215 +=== DS6 – relay 4 indicator ===
227 227  
217 +|**State**|**Description**
218 +|**Lights green**|Relay #4 is closed
219 +|**Off**|Relay #4 is opened
220 +
228 228  
1731516474613-418.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731516577472-301.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731516593096-166.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731516685999-633.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731516942455-641.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731517023208-641.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731517025702-799.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731517206246-979.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -4.2 KB
Content
1731517946345-632.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -107.3 KB
Content
1732198827034-560.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +1.1 KB
Content
1732198890482-787.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 KB
Content
1732198896526-660.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 KB
Content
1732198937514-731.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +7.1 KB
Content