Skip to Content
Last modified by Admin on 2025/07/15 17:33
From version 26.1
edited by Admin
on 2024/11/21 14:13
Change comment: Uploaded new attachment "1732198397369-222.png", version {1}
To version 67.1
edited by Admin
on 2025/07/15 17:30
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -2. Connection
1 +2. Installation and connection
Parent
... ... @@ -1,1 +1,1 @@
1 -drafts.bms-main-2-1.WebHome
1 +Battery management systems.BMS Main 2\.1.WebHome
Content
... ... @@ -1,5 +1,35 @@
1 -== 2.1 Connection procedure ==
1 +(% data-numbered-headings-start="2" style="--numbered-headings-start: 1;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 += Installation and connection =
2 2  
4 +== Safety rules ==
5 +
6 +To perform the protection functions, the BMS must be able to disconnect the battery from the load and charger. To do this, **at least one contactor** able to break the load and charge circuits must be connected to the BMS.
7 +
8 +Before use, **configure the system**. Proper operation of the BMS is possible only if it is correctly configured.
9 +
10 +(% class="box errormessage" %)
11 +(((
12 +The BMS can be connected to batteries with life-threatening and health-hazardous voltage levels. When working with high-voltage batteries, observe electrical safety regulations, use safety glasses, protective clothing, insulated tools and appliances. To prevent the damage of device avoid electrostatic discharges while working with the battery.
13 +)))
14 +
15 +(% class="box errormessage" %)
16 +(((
17 +The system is not designed to operate with batteries whose total voltage exceeds 1200 V.
18 +)))
19 +
20 +== Installation procedure ==
21 +
22 +Overall and mounting dimensions of the BMS Main 2.1 are shown below.
23 +
24 +
25 +(% style="width:494px" %)
26 +|**Parameter**|(% style="width:178px" %)**Value**
27 +|Overall dimensions (length × width × height), mm|(% style="width:178px" %)120 × 120 × 17
28 +|Mounting dimensions (length × width), mm|(% style="width:178px" %)114 × 114
29 +|Mounting holes|(% style="width:178px" %)M3
30 +
31 +== Connection procedure ==
32 +
3 3  The mounting area of the BMS Main 2.1 must be protected from mechanical particles (dust, dirt, large objects) and water. The installation site must provide convenient access for subsequent connection to the device’s headers.
4 4  
5 5  1. Connect the charging and discharging contactors to the P6-P9 headers.
... ... @@ -7,214 +7,231 @@
7 7  1. Connect the BMS Main 2.1 to the on-board CAN network. Observe the rules for connecting CAN devices. If the BMS Main 2.1 is the last device on a bus, close pins 1-2 on the P21 jumper, otherwise leave the jumper on pins 2-3.
8 8  1. Connect a power supply to the P1 header. It is not recommended to power the BMS Main 2.1 from the battery only, since at a critical discharge of the battery, it is not possible to turn on the BMS and close the charging contactor.
9 9  
10 -== 2.2 ​​​​Headers description ==
40 +== ​​​​Headers description ==
11 11  
12 12  The BMS Main 2.1 headers are shown in figure below.
13 13  
14 -[[The BMS Main 2.1 headers>>image:1731517946345-632.png||height="417" width="451"]]
44 +[[image:1731516393377-928.jpeg||alt="1731517946345-632.png" data-xwiki-image-style-alignment="center" height="417" width="451"]]
15 15  
16 -(% class="wikigeneratedid" %)
17 -Following chapters describes the BMS Main 2.1 headers pinout.
46 +(% class="box warningmessage" %)
47 +(((
48 +**Attention!**
49 +All headers are shown from the device side!
50 +)))
18 18  
19 -=== 2.2.1 P1 – header for power supply ===
52 +=== P1 – header for power supply ===
20 20  
21 -[[image:1731516593096-166.png||height="80" width="42"]]
54 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
22 22  
23 -(% style="width:339px" %)
24 -|(% style="width:71px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:174px" %)**Description**
25 -|(% style="width:71px" %)**1**|(% style="width:91px" %)**GND**|(% style="width:174px" %)Ground
26 -|(% style="width:71px" %)**2**|(% style="width:91px" %)**V+**|(% style="width:174px" %)Supply voltage 9-30V
56 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
27 27  
28 -=== 2.2.2 P15 – header for BMS Logic ===
58 +|**Pin**|**Name**|**Description**
59 +|**1**|**GND**|Ground
60 +|**2**|**V+**|Supply voltage 9-30V
29 29  
30 -[[image:1731516577472-301.png||height="77" width="71"]]
62 +=== P15 – header for BMS Logic ===
31 31  
32 -(% style="width:524px" %)
33 -|(% style="width:69px" %)**Pin**|(% style="width:97px" %)**Name**|(% style="width:355px" %)**Description**
34 -|(% style="width:69px" %)**1**|(% style="width:97px" %)**RS485_A**|(% style="width:355px" %)RS-485 line A for communication with BMS Logic
35 -|(% style="width:69px" %)**2**|(% style="width:97px" %)**RS485_B**|(% style="width:355px" %)RS-485 line B for communication with BMS Logic
36 -|(% style="width:69px" %)**3**|(% style="width:97px" %)**+5V**|(% style="width:355px" %)Supply voltage for BMS Logic
37 -|(% style="width:69px" %)**4**|(% style="width:97px" %)**GND**|(% style="width:355px" %)Ground
64 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
38 38  
39 -=== 2.2.3 P12 – header for current sensor ===
66 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
40 40  
41 -[[image:1731516685999-633.png||height="74" width="68"]]
68 +|**Pin**|**Name**|**Description**
69 +|**1**|**RS485_A**|RS-485 line A for communication with BMS Logic
70 +|**2**|**RS485_B**|RS-485 line B for communication with BMS Logic
71 +|**3**|**+5V**|Supply voltage for BMS Logic
72 +|**4**|**GND**|Ground
42 42  
43 -(% style="width:531px" %)
44 -|(% style="width:75px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:360px" %)**Description**
45 -|(% style="width:75px" %)**1**|(% style="width:93px" %)**+5V**|(% style="width:360px" %)Supply voltage for the current sensor 5V, max 50 mA
46 -|(% style="width:75px" %)**2**|(% style="width:93px" %)**GND**|(% style="width:360px" %)Ground
47 -|(% style="width:75px" %)**3**|(% style="width:93px" %)**Vcs**|(% style="width:360px" %)ADC input (current sensor output)
48 -|(% style="width:75px" %)**4**|(% style="width:93px" %)**Vref**|(% style="width:360px" %)ADC input (current sensor reference signal)
74 +=== P12 – header for current sensor ===
49 49  
50 -=== 2.2.4 P13 – header for humidity sensor ===
76 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
51 51  
52 -[[image:1731516942455-641.png||height="70" width="64"]]
78 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
53 53  
54 -(% style="width:531px" %)
55 -|(% style="width:77px" %)**Pin**|(% style="width:92px" %)**Name**|(% style="width:359px" %)**Description**
56 -|(% style="width:77px" %)**1**|(% style="width:92px" %)**+5V**|(% style="width:359px" %)Supply voltage 5 V, max 50 mA
57 -|(% style="width:77px" %)**2**|(% style="width:92px" %)**GND**|(% style="width:359px" %)Ground
58 -|(% style="width:77px" %)**3**|(% style="width:92px" %)**Vhs**|(% style="width:359px" %)ADC input (humidity sensor output)
59 -|(% style="width:77px" %)**4**|(% style="width:92px" %)**Vts**|(% style="width:359px" %)ADC input (temperature sensor output)
80 +|**Pin**|**Name**|**Description**
81 +|**1**|**+5V**|Supply voltage for the current sensor 5V, max 50 mA
82 +|**2**|**GND**|Ground
83 +|**3**|**Vcs**|ADC input (current sensor output)
84 +|**4**|**Vref**|ADC input (current sensor reference signal)
60 60  
61 -=== 2.2.5 P8 – header of relay 1 ===
86 +=== P13 – header for humidity sensor ===
62 62  
63 -[[image:1731517023208-641.png||height="80" width="42"]]
88 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
64 64  
90 +[[image:1732198896526-660.png||data-xwiki-image-style-alignment="center" height="70" width="64"]]
91 +
92 +|**Pin**|**Name**|**Description**
93 +|**1**|**+5V**|Supply voltage 5 V, max 50 mA
94 +|**2**|**GND**|Ground
95 +|**3**|**Vhs**|ADC input (humidity sensor output)
96 +|**4**|**Vts**|ADC input (temperature sensor output)
97 +
98 +=== P8 – header of relay 1 ===
99 +
100 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
101 +
102 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
103 +
65 65  By default, relay 1 is used to control the discharging contactor.
66 66  
67 -(% style="width:527px" %)
68 -|(% style="width:82px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:351px" %)**Description**
69 -|(% style="width:82px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:351px" %)Switching voltage (up to 55V, max 2A)
70 -|(% style="width:82px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:351px" %)Normally open contact
106 +|**Pin**|**Name**|**Description**
107 +|**1**|**V+**|Switching voltage (up to 55V, max 3A)
108 +|**2**|**NO**|Normally open contact
71 71  
72 -=== 2.2.6 P9 – header of relay 2 ===
110 +Contactor connection example for all relays:
73 73  
74 -[[image:1731517025702-799.png||height="71" width="37"]]
112 +[[image:1741619814065-850.png||height="189" width="252"]]
75 75  
114 +=== P9 – header of relay 2 ===
115 +
116 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
117 +
118 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
119 +
76 76  By default, relay 2 is used to output the “Allow charging” signal.
77 77  
78 -(% style="width:524px" %)
79 -|(% style="width:89px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:341px" %)**Description**
80 -|(% style="width:89px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:341px" %)Switching voltage (up to 55V, max 2A)
81 -|(% style="width:89px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:341px" %)Normally open contact
122 +|**Pin**|**Name**|**Description**
123 +|**1**|**V+**|Switching voltage (up to 55V, max 3A)
124 +|**2**|**NO**|Normally open contact
82 82  
83 -=== 2.2.7 P6 – header of relay 3 ===
126 +Contactor connection example: see relay 1.
84 84  
85 -[[image:1731517025702-799.png||height="67" width="35"]]
128 +=== P6 – header of relay 3 ===
86 86  
130 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
131 +
132 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
133 +
87 87  By default, relay 3 is used to control the charging contactor.
88 88  
89 -(% style="width:524px" %)
90 -|(% style="width:101px" %)**Pin**|(% style="width:88px" %)**Name**|(% style="width:332px" %)**Description**
91 -|(% style="width:101px" %)**1**|(% style="width:88px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
92 -|(% style="width:101px" %)**2**|(% style="width:88px" %)**NO**|(% style="width:332px" %)Normally open contact
136 +|**Pin**|**Name**|**Description**
137 +|**1**|**V+**|Switching voltage up to 55V,
138 +up to 8A (board rev. 2.1b), up to 3A (board rev. 2.1c)
139 +|**2**|**NO**|Normally open contact
93 93  
94 -=== 2.2.8 P7 – header of relay 4 ===
141 +Contactor connection example: see relay 1.
95 95  
96 -[[image:1731517025702-799.png||height="65" width="34"]]
143 +=== P7 – header of relay 4 ===
97 97  
145 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
146 +
147 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
148 +
98 98  By default, relay 4 is used to control the heater.
99 99  
100 -(% style="width:530px" %)
101 -|(% style="width:102px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:332px" %)**Description**
102 -|(% style="width:102px" %)**1**|(% style="width:93px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
103 -|(% style="width:102px" %)**2**|(% style="width:93px" %)**NO**|(% style="width:332px" %)Normally open contact
151 +|**Pin**|**Name**|**Description**
152 +|**1**|**V+**|Switching voltage up to 55V,
153 +up to 8A (board rev. 2.1b), up to 3A (board rev. 2.1c)
154 +|**2**|**NO**|Normally open contact
104 104  
105 -=== 2.2.9 P14 – header for CAN and RS-485 interfaces ===
156 +Contactor connection example: see relay 1.
106 106  
107 -[[image:1731517180930-597.png||height="81" width="113"]]
158 +=== P14 – header for CAN and RS-485 interfaces ===
108 108  
160 +Receptacle Housing: Molex 430250600. Terminals: Molex 43030
161 +
162 +[[image:1731517180930-597.png||data-xwiki-image-style-alignment="center" height="81" width="113"]]
163 +
109 109  (% style="width:641px" %)
110 -|(% style="width:107px" %)**Pin**|(% style="width:127px" %)**Name**|(% style="width:404px" %)**Description**
111 -|(% style="width:107px" %)**1**|(% style="width:127px" %)**EXT_RS485_A**|(% style="width:404px" %)RS-485 line A for communication with external equipment
112 -|(% style="width:107px" %)**2**|(% style="width:127px" %)**CAN_H**|(% style="width:404px" %)CAN H line for communication with external equipment
113 -|(% style="width:107px" %)**3**|(% style="width:127px" %)**+5V_CAN**|(% style="width:404px" %)Supply voltage 5V for external devices, max 200 mA
114 -|(% style="width:107px" %)**4**|(% style="width:127px" %)**EXT_RS485_B**|(% style="width:404px" %)RS-485 line B for communication with external equipment
115 -|(% style="width:107px" %)**5**|(% style="width:127px" %)**CAN_L**|(% style="width:404px" %)CAN L line for communication with external equipment
116 -|(% style="width:107px" %)**6**|(% style="width:127px" %)**GND_CAN**|(% style="width:404px" %)Ground
165 +|**Pin**|**Name**|**Description**
166 +|**1**|**EXT_RS485_A**|RS-485 line A for communication with external equipment
167 +|**2**|**CAN_H**|CAN H line for communication with external equipment
168 +|**3**|**+5V_CAN**|Supply voltage 5V for external devices, max 200 mA
169 +|**4**|**EXT_RS485_B**|RS-485 line B for communication with external equipment
170 +|**5**|**CAN_L**|CAN L line for communication with external equipment
171 +|**6**|**GND_CAN**|Ground
117 117  
118 -=== 2.2.10 P21 – CAN termination resistor jumper ===
173 +=== P21 – CAN termination resistor jumper ===
119 119  
120 -[[image:1731517188900-976.png||height="78" width="149"]]
175 +[[image:1731517188900-976.png||data-xwiki-image-style-alignment="center" height="78" width="149"]]
121 121  
122 122  To connect the termination resistor between the lines **CAN_H** and **CAN_L**, install a jumper, according to the P21 pinout:
123 123  
124 -(% style="width:643px" %)
125 -|**Pin**|(% style="width:122px" %)**Name**|(% style="width:400px" %)**Description**
126 -|**1-2**|(% style="width:122px" %)**120 Ohm**|(% style="width:400px" %)Termination resistor 120 Ohm is connected
127 -|**2-3**|(% style="width:122px" %)**-**|(% style="width:400px" %)Termination resistor 120 Ohm is not connected
179 +|**Pin**|**Name**|**Description**
180 +|**1-2**|**120 Ohm**|Termination resistor 120 Ohm is connected
181 +|**2-3**|**-**|Termination resistor 120 Ohm is not connected
128 128  
129 -=== 2.2.11 P22 - RS-485 termination resistor jumper ===
183 +=== P22 - RS-485 termination resistor jumper ===
130 130  
131 -[[image:1731517195672-298.png||height="81" width="155"]]
185 +[[image:1731517195672-298.png||data-xwiki-image-style-alignment="center" height="81" width="155"]]
132 132  
133 133  To connect the termination resistor between the **EXT_RS485_A** and **EXT_RS485_B** lines, install a jumper according to the P22 pinout:
134 134  
135 -(% style="width:644px" %)
136 -|**Pin**|(% style="width:121px" %)**Name**|(% style="width:402px" %)**Description**
137 -|**1-2**|(% style="width:121px" %)**120 Ohm**|(% style="width:402px" %)Terminating resistor 120 Ohm is connected
138 -|**2-3**|(% style="width:121px" %)**-**|(% style="width:402px" %)Terminating resistor 120 Ohm is not connected
189 +|**Pin**|**Name**|**Description**
190 +|**1-2**|**120 Ohm**|Terminating resistor 120 Ohm is connected
191 +|**2-3**|**-**|Terminating resistor 120 Ohm is not connected
139 139  
140 -=== 2.2.12 P11 – header for discrete inputs/outputs ===
193 +=== P11 – header for discrete inputs/outputs ===
141 141  
142 -[[image:1731517206246-979.png||height="81" width="258"]]
195 +Receptacle Housing: Molex 430251600. Terminals: Molex 43030
143 143  
144 -(% style="width:584px" %)
145 -|(% style="width:98px" %)**Pin**|(% style="width:157px" %)**Name**|(% style="width:326px" %)**Description**
146 -|(% style="width:98px" %)**16**|(% style="width:157px" %)**IN_1**|(% style="width:326px" %)Discrete input #1 “dry contact” (+5V)
147 -|(% style="width:98px" %)**8**|(% style="width:157px" %)**GND_1**|(% style="width:326px" %)Discrete input #1 “dry contact” (ground)
148 -|(% style="width:98px" %)**15**|(% style="width:157px" %)**IN_2**|(% style="width:326px" %)Discrete input #2 “dry contact” (+5V)
149 -|(% style="width:98px" %)**7**|(% style="width:157px" %)**GND_2**|(% style="width:326px" %)Discrete input #2 “dry contact” (ground)
150 -|(% style="width:98px" %)**14**|(% style="width:157px" %)**IN_3**|(% style="width:326px" %)Discrete input #3 “dry contact” (+5V)
151 -|(% style="width:98px" %)**6**|(% style="width:157px" %)**GND_3**|(% style="width:326px" %)Discrete input #3 “dry contact” (ground)
152 -|(% style="width:98px" %)**13**|(% style="width:157px" %)**IN_4**|(% style="width:326px" %)Discrete input #4 “dry contact” (+5V)
153 -|(% style="width:98px" %)**5**|(% style="width:157px" %)**GND_4**|(% style="width:326px" %)Discrete input #4 “dry contact” (ground)
154 -|(% style="width:98px" %)**12**|(% style="width:157px" %)**OUT_4**|(% style="width:326px" %)Discrete output #4 (+5V, 20mA)
155 -|(% style="width:98px" %)**4**|(% style="width:157px" %)**GND_OUT_4**|(% style="width:326px" %)Discrete output #4 (ground)
156 -|(% style="width:98px" %)**11**|(% style="width:157px" %)**OUT_3**|(% style="width:326px" %)Discrete output #3 (+5V, 20mA)
157 -|(% style="width:98px" %)**3**|(% style="width:157px" %)**GND_OUT_3**|(% style="width:326px" %)Discrete output #3 (ground)
158 -|(% style="width:98px" %)**10**|(% style="width:157px" %)**OUT_2**|(% style="width:326px" %)Discrete output #2 (+5V, 20mA)
159 -|(% style="width:98px" %)**2**|(% style="width:157px" %)**GND_OUT_2**|(% style="width:326px" %)Discrete output #2 (ground)
160 -|(% style="width:98px" %)**9**|(% style="width:157px" %)**OUT_1**|(% style="width:326px" %)Discrete output #1 (+5V, 20mA)
161 -|(% style="width:98px" %)**1**|(% style="width:157px" %)**GND_OUT_1**|(% style="width:326px" %)Discrete output #1 (ground)
197 +[[image:1732198937514-731.png||data-xwiki-image-style-alignment="center" height="85" width="272"]]
162 162  
163 -= 2.3 Indicators =
199 +|**Pin**|**Name**|**Description**
200 +|**16**|**IN_1**|Discrete input #1 “dry contact” (+5V)
201 +|**8**|**GND_1**|Discrete input #1 “dry contact” (ground)
202 +|**15**|**IN_2**|Discrete input #2 “dry contact” (+5V)
203 +|**7**|**GND_2**|Discrete input #2 “dry contact” (ground)
204 +|**14**|**IN_3**|Discrete input #3 “dry contact” (+5V)
205 +|**6**|**GND_3**|Discrete input #3 “dry contact” (ground)
206 +|**13**|**IN_4**|Discrete input #4 “dry contact” (+5V)
207 +|**5**|**GND_4**|Discrete input #4 “dry contact” (ground)
208 +|**12**|**OUT_4**|Discrete output #4 (+5V, 20mA)
209 +|**4**|**GND_OUT_4**|Discrete output #4 (ground)
210 +|**11**|**OUT_3**|Discrete output #3 (+5V, 20mA)
211 +|**3**|**GND_OUT_3**|Discrete output #3 (ground)
212 +|**10**|**OUT_2**|Discrete output #2 (+5V, 20mA)
213 +|**2**|**GND_OUT_2**|Discrete output #2 (ground)
214 +|**9**|**OUT_1**|Discrete output #1 (+5V, 20mA)
215 +|**1**|**GND_OUT_1**|Discrete output #1 (ground)
164 164  
165 -=== 2.3.1 DS1 – power indicator ===
217 +== Indicators ==
166 166  
167 -(% style="width:442px" %)
168 -|(% style="width:138px" %)**State**|(% style="width:301px" %)**Description**
169 -|(% style="width:138px" %)**Lights red**|(% style="width:301px" %)The device is powered
170 -|(% style="width:138px" %)**Off**|(% style="width:301px" %)The device is not powered
219 +=== DS1 – power indicator ===
171 171  
172 -=== 2.3.2 DS2 – operation indicator ===
221 +|**State**|**Description**
222 +|**Lights red**|The device is powered
223 +|**Off**|The device is not powered
173 173  
174 -(% style="width:442px" %)
175 -|(% style="width:137px" %)**State**|(% style="width:302px" %)**Description**
176 -|(% style="width:137px" %)**Blinking green**|(% style="width:302px" %)The BMS firmware is running
177 -|(% style="width:137px" %)**Off**|(% style="width:302px" %)The BMS firmware is not running
225 +=== DS2 – operation indicator ===
178 178  
179 -=== 2.3.3 DS3 – communication indicator ===
227 +|**State**|**Description**
228 +|**Blinking green**|The BMS firmware is running
229 +|**Off**|The BMS firmware is not running
180 180  
181 -(% style="width:539px" %)
182 -|(% style="width:175px" %)**State**|(% style="width:361px" %)**Description**
183 -|(% style="width:175px" %)**Blinking yellow (2Hz)**|(% style="width:361px" %)Initializing communication with BMS Logic boards
184 -|(% style="width:175px" %)**Blinking yellow (25Hz)**|(% style="width:361px" %)Communication with BMS Logic is established
231 +=== DS3 – communication indicator ===
185 185  
186 -=== 2.3.4 DS4 – error indicator ===
233 +|**State**|**Description**
234 +|**Blinking yellow (2Hz)**|Initializing communication with BMS Logic boards
235 +|**Blinking yellow (25Hz)**|Communication with BMS Logic is established
187 187  
188 -(% style="width:539px" %)
189 -|(% style="width:176px" %)**State**|(% style="width:360px" %)**Description**
190 -|(% style="width:176px" %)**Blinking red**|(% style="width:360px" %)Errors in communication with BMS Logic
237 +=== DS4 – error indicator ===
191 191  
192 -=== 2.3.5 DS7 – relay 1 indicator ===
193 193  
194 -(% style="width:541px" %)
195 -|(% style="width:179px" %)**State**|(% style="width:359px" %)**Description**
196 -|(% style="width:179px" %)**Lights green**|(% style="width:359px" %)Relay #1 is closed
197 -|(% style="width:179px" %)**Off**|(% style="width:359px" %)Relay #1 is opened
240 +|(**State**|**Description**
241 +|(**Blinking red**|Errors in communication with BMS Logic
198 198  
199 -=== 2.3.6 DS8 – relay 2 indicator ===
243 +=== DS7 – relay 1 indicator ===
200 200  
201 -(% style="width:542px" %)
202 -|(% style="width:180px" %)**State**|(% style="width:359px" %)**Description**
203 -|(% style="width:180px" %)**Lights green**|(% style="width:359px" %)Relay #2 is closed
204 -|(% style="width:180px" %)**Off**|(% style="width:359px" %)Relay #2 is opened
245 +|**State**|**Description**
246 +|**Lights green**|Relay #1 is closed
247 +|**Off**|Relay #1 is opened
205 205  
206 -=== 2.3.7 DS5 – relay 3 indicator ===
249 +=== DS8 – relay 2 indicator ===
207 207  
208 -(% style="width:542px" %)
209 -|(% style="width:183px" %)**State**|(% style="width:356px" %)**Description**
210 -|(% style="width:183px" %)**Lights green**|(% style="width:356px" %)Relay #3 is closed
211 -|(% style="width:183px" %)**Off**|(% style="width:356px" %)Relay #3 is opened
251 +|**State**|**Description**
252 +|**Lights green**|Relay #2 is closed
253 +|**Off**|Relay #2 is opened
212 212  
213 -=== 2.3.8 DS6 – relay 4 indicator ===
255 +=== DS5 – relay 3 indicator ===
214 214  
215 -(% style="width:542px" %)
216 -|(% style="width:187px" %)**State**|(% style="width:352px" %)**Description**
217 -|(% style="width:187px" %)**Lights green**|(% style="width:352px" %)Relay #4 is closed
218 -|(% style="width:187px" %)**Off**|(% style="width:352px" %)Relay #4 is opened
257 +|**State**|**Description**
258 +|**Lights green**|Relay #3 is closed
259 +|**Off**|Relay #3 is opened
219 219  
261 +=== DS6 – relay 4 indicator ===
262 +
263 +|**State**|**Description**
264 +|**Lights green**|Relay #4 is closed
265 +|**Off**|Relay #4 is opened
266 +
220 220  
1731516474613-418.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731516577472-301.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731516593096-166.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731516685999-633.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731516942455-641.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731517023208-641.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731517025702-799.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731517206246-979.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -4.2 KB
Content
1731517946345-632.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -107.3 KB
Content
1732198827034-560.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +1.1 KB
Content
1732198890482-787.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 KB
Content
1732198896526-660.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 KB
Content
1732198937514-731.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +7.1 KB
Content
1741619628288-759.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +29.2 KB
Content
1741619637854-961.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +29.2 KB
Content
1741619700532-367.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +14.1 KB
Content
1741619814065-850.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +15.1 KB
Content
1741620022836-867.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +13.3 KB
Content