Skip to Content
Last modified by Admin on 2025/03/18 12:51
From version 22.2
edited by Admin
on 2024/11/19 07:59
Change comment: There is no comment for this version
To version 24.1
edited by Admin
on 2024/11/19 08:01
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -16,7 +16,7 @@
16 16  
17 17  === P1 – header for power supply ===
18 18  
19 -[[image:1731516593096-166.png]]
19 +[[image:1731516593096-166.png||height="80" width="42"]]
20 20  
21 21  (% style="width:339px" %)
22 22  |(% style="width:71px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:174px" %)**Description**
... ... @@ -25,7 +25,7 @@
25 25  
26 26  === P15 – header for BMS Logic ===
27 27  
28 -[[image:1731516577472-301.png]]
28 +[[image:1731516577472-301.png||height="77" width="71"]]
29 29  
30 30  (% style="width:524px" %)
31 31  |(% style="width:69px" %)**Pin**|(% style="width:97px" %)**Name**|(% style="width:355px" %)**Description**
... ... @@ -36,7 +36,7 @@
36 36  
37 37  === P12 – header for current sensor ===
38 38  
39 -[[image:1731516685999-633.png]]
39 +[[image:1731516685999-633.png||height="74" width="68"]]
40 40  
41 41  (% style="width:531px" %)
42 42  |(% style="width:75px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:360px" %)**Description**
... ... @@ -47,7 +47,7 @@
47 47  
48 48  === P13 – header for humidity sensor ===
49 49  
50 -[[image:1731516942455-641.png]]
50 +[[image:1731516942455-641.png||height="70" width="64"]]
51 51  
52 52  (% style="width:531px" %)
53 53  |(% style="width:77px" %)**Pin**|(% style="width:92px" %)**Name**|(% style="width:359px" %)**Description**
... ... @@ -58,7 +58,7 @@
58 58  
59 59  === P8 – header of relay 1 ===
60 60  
61 -[[image:1731517023208-641.png]]
61 +[[image:1731517023208-641.png||height="80" width="42"]]
62 62  
63 63  By default, relay 1 is used to control the discharging contactor.
64 64  
... ... @@ -69,7 +69,7 @@
69 69  
70 70  === P9 – header of relay 2 ===
71 71  
72 -[[image:1731517025702-799.png]]
72 +[[image:1731517025702-799.png||height="71" width="37"]]
73 73  
74 74  By default, relay 2 is used to output the “Allow charging” signal.
75 75  
... ... @@ -80,7 +80,7 @@
80 80  
81 81  === P6 – header of relay 3 ===
82 82  
83 -[[image:1731517025702-799.png]]
83 +[[image:1731517025702-799.png||height="67" width="35"]]
84 84  
85 85  By default, relay 3 is used to control the charging contactor.
86 86  
... ... @@ -91,7 +91,7 @@
91 91  
92 92  === P7 – header of relay 4 ===
93 93  
94 -[[image:1731517025702-799.png]]
94 +[[image:1731517025702-799.png||height="65" width="34"]]
95 95  
96 96  By default, relay 4 is used to control the heater.
97 97  
... ... @@ -102,7 +102,7 @@
102 102  
103 103  === P14 – header for CAN and RS-485 interfaces ===
104 104  
105 -[[image:1731517180930-597.png]]
105 +[[image:1731517180930-597.png||height="81" width="113"]]
106 106  
107 107  (% style="width:641px" %)
108 108  |(% style="width:107px" %)**Pin**|(% style="width:127px" %)**Name**|(% style="width:404px" %)**Description**
... ... @@ -115,7 +115,7 @@
115 115  
116 116  === P21 – CAN termination resistor jumper ===
117 117  
118 -[[image:1731517188900-976.png]]
118 +[[image:1731517188900-976.png||height="78" width="149"]]
119 119  
120 120  To connect the termination resistor between the lines **CAN_H** and **CAN_L**, install a jumper, according to the P21 pinout:
121 121  
... ... @@ -137,7 +137,7 @@
137 137  
138 138  === P11 – header for discrete inputs/outputs ===
139 139  
140 -[[image:1731517206246-979.png]]
140 +[[image:1731517206246-979.png||height="81" width="258"]]
141 141  
142 142  (% style="width:584px" %)
143 143  |(% style="width:98px" %)**Pin**|(% style="width:157px" %)**Name**|(% style="width:326px" %)**Description**