Skip to Content
Last modified by Admin on 2025/03/18 12:51
From version 21.2
edited by Admin
on 2024/11/19 07:55
Change comment: There is no comment for this version
To version 21.3
edited by Admin
on 2024/11/19 07:56
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -49,11 +49,12 @@
49 49  
50 50  [[image:1731516942455-641.png||data-xwiki-image-style-alignment="center"]]
51 51  
52 -|**Pin**|**Name**|**Description**
53 -|**1**|**+5V**|Supply voltage 5 V, max 50 mA
54 -|**2**|**GND**|Ground
55 -|**3**|**Vhs**|ADC input (humidity sensor output)
56 -|**4**|**Vts**|ADC input (temperature sensor output)
52 +(% style="width:531px" %)
53 +|(% style="width:77px" %)**Pin**|(% style="width:92px" %)**Name**|(% style="width:359px" %)**Description**
54 +|(% style="width:77px" %)**1**|(% style="width:92px" %)**+5V**|(% style="width:359px" %)Supply voltage 5 V, max 50 mA
55 +|(% style="width:77px" %)**2**|(% style="width:92px" %)**GND**|(% style="width:359px" %)Ground
56 +|(% style="width:77px" %)**3**|(% style="width:92px" %)**Vhs**|(% style="width:359px" %)ADC input (humidity sensor output)
57 +|(% style="width:77px" %)**4**|(% style="width:92px" %)**Vts**|(% style="width:359px" %)ADC input (temperature sensor output)
57 57  
58 58  === P8 – header of relay 1 ===
59 59  
... ... @@ -61,9 +61,10 @@
61 61  
62 62  By default, relay 1 is used to control the discharging contactor.
63 63  
64 -|**Pin**|**Name**|**Description**
65 -|**1**|**V+**|Switching voltage (up to 55V, max 2A)
66 -|**2**|**NO**|Normally open contact
65 +(% style="width:527px" %)
66 +|(% style="width:82px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:351px" %)**Description**
67 +|(% style="width:82px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:351px" %)Switching voltage (up to 55V, max 2A)
68 +|(% style="width:82px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:351px" %)Normally open contact
67 67  
68 68  === P9 – header of relay 2 ===
69 69  
... ... @@ -71,9 +71,10 @@
71 71  
72 72  By default, relay 2 is used to output the “Allow charging” signal.
73 73  
74 -|**Pin**|**Name**|**Description**
75 -|**1**|**V+**|Switching voltage (up to 55V, max 2A)
76 -|**2**|**NO**|Normally open contact
76 +(% style="width:524px" %)
77 +|(% style="width:89px" %)**Pin**|(% style="width:91px" %)**Name**|(% style="width:341px" %)**Description**
78 +|(% style="width:89px" %)**1**|(% style="width:91px" %)**V+**|(% style="width:341px" %)Switching voltage (up to 55V, max 2A)
79 +|(% style="width:89px" %)**2**|(% style="width:91px" %)**NO**|(% style="width:341px" %)Normally open contact
77 77  
78 78  === P6 – header of relay 3 ===
79 79  
... ... @@ -81,9 +81,10 @@
81 81  
82 82  By default, relay 3 is used to control the charging contactor.
83 83  
84 -|**Pin**|**Name**|**Description**
85 -|**1**|**V+**|Switching voltage (up to 55V, max 8A)
86 -|**2**|**NO**|Normally open contact
87 +(% style="width:524px" %)
88 +|(% style="width:101px" %)**Pin**|(% style="width:88px" %)**Name**|(% style="width:332px" %)**Description**
89 +|(% style="width:101px" %)**1**|(% style="width:88px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
90 +|(% style="width:101px" %)**2**|(% style="width:88px" %)**NO**|(% style="width:332px" %)Normally open contact
87 87  
88 88  === P7 – header of relay 4 ===
89 89  
... ... @@ -91,21 +91,23 @@
91 91  
92 92  By default, relay 4 is used to control the heater.
93 93  
94 -|**Pin**|**Name**|**Description**
95 -|**1**|**V+**|Switching voltage (up to 55V, max 8A)
96 -|**2**|**NO**|Normally open contact
98 +(% style="width:530px" %)
99 +|(% style="width:102px" %)**Pin**|(% style="width:93px" %)**Name**|(% style="width:332px" %)**Description**
100 +|(% style="width:102px" %)**1**|(% style="width:93px" %)**V+**|(% style="width:332px" %)Switching voltage (up to 55V, max 8A)
101 +|(% style="width:102px" %)**2**|(% style="width:93px" %)**NO**|(% style="width:332px" %)Normally open contact
97 97  
98 98  === P14 – header for CAN and RS-485 interfaces ===
99 99  
100 100  [[image:1731517180930-597.png||data-xwiki-image-style-alignment="center"]]
101 101  
102 -|**Pin**|**Name**|**Description**
103 -|**1**|**EXT_RS485_A**|RS-485 line A for communication with external equipment
104 -|**2**|**CAN_H**|CAN H line for communication with external equipment
105 -|**3**|**+5V_CAN**|Supply voltage 5V for external devices, max 200 mA
106 -|**4**|**EXT_RS485_B**|RS-485 line B for communication with external equipment
107 -|**5**|**CAN_L**|CAN L line for communication with external equipment
108 -|**6**|**GND_CAN**|Ground
107 +(% style="width:641px" %)
108 +|(% style="width:107px" %)**Pin**|(% style="width:127px" %)**Name**|(% style="width:404px" %)**Description**
109 +|(% style="width:107px" %)**1**|(% style="width:127px" %)**EXT_RS485_A**|(% style="width:404px" %)RS-485 line A for communication with external equipment
110 +|(% style="width:107px" %)**2**|(% style="width:127px" %)**CAN_H**|(% style="width:404px" %)CAN H line for communication with external equipment
111 +|(% style="width:107px" %)**3**|(% style="width:127px" %)**+5V_CAN**|(% style="width:404px" %)Supply voltage 5V for external devices, max 200 mA
112 +|(% style="width:107px" %)**4**|(% style="width:127px" %)**EXT_RS485_B**|(% style="width:404px" %)RS-485 line B for communication with external equipment
113 +|(% style="width:107px" %)**5**|(% style="width:127px" %)**CAN_L**|(% style="width:404px" %)CAN L line for communication with external equipment
114 +|(% style="width:107px" %)**6**|(% style="width:127px" %)**GND_CAN**|(% style="width:404px" %)Ground
109 109  
110 110  === P21 – CAN termination resistor jumper ===
111 111  
... ... @@ -123,9 +123,9 @@
123 123  
124 124  To connect the termination resistor between the **EXT_RS485_A** and **EXT_RS485_B** lines, install a jumper according to the P22 pinout:
125 125  
126 -|**Pin**|**Name**|**Description**
127 -|**1-2**|**120 Ohm**|Terminating resistor 120 Ohm is connected
128 -|**2-3**|**-**|Terminating resistor 120 Ohm is not connected
132 +|**Pin**|(% style="width:108px" %)**Name**|(% style="width:1296px" %)**Description**
133 +|**1-2**|(% style="width:108px" %)**120 Ohm**|(% style="width:1296px" %)Terminating resistor 120 Ohm is connected
134 +|**2-3**|(% style="width:108px" %)**-**|(% style="width:1296px" %)Terminating resistor 120 Ohm is not connected
129 129  
130 130  === P11 – header for discrete inputs/outputs ===
131 131