Skip to Content
Last modified by Admin on 2025/07/15 17:33
From version 16.1
edited by Admin
on 2024/11/13 17:11
Change comment: There is no comment for this version
To version 69.1
edited by Admin
on 2025/07/15 17:31
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -2. Connection
1 +2. Installation and connection
Parent
... ... @@ -1,1 +1,1 @@
1 -Additional modules.BMS Main 2\.1.WebHome
1 +Battery management systems.BMS Main 2\.1.WebHome
Content
... ... @@ -1,188 +1,268 @@
1 -= ​​​​Headers =
1 +(% data-numbered-headings-start="2" style="--numbered-headings-start: 1;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 += Installation and connection =
2 2  
4 +== Safety rules ==
5 +
6 +To perform the protection functions, the BMS must be able to disconnect the battery from the load and charger. To do this, **at least one contactor** able to break the load and charge circuits must be connected to the BMS.
7 +
8 +Before use, **configure the system**. Proper operation of the BMS is possible only if it is correctly configured.
9 +
10 +(% class="box errormessage" %)
11 +(((
12 +The BMS can be connected to batteries with life-threatening and health-hazardous voltage levels. When working with high-voltage batteries, observe electrical safety regulations, use safety glasses, protective clothing, insulated tools and appliances. To prevent the damage of device avoid electrostatic discharges while working with the battery.
13 +)))
14 +
15 +(% class="box errormessage" %)
16 +(((
17 +The system is not designed to operate with batteries whose total voltage exceeds 1200 V.
18 +)))
19 +
20 +== Installation procedure ==
21 +
22 +Overall and mounting dimensions of the BMS Main 2.1 are shown below.
23 +
24 +[[image:1752600650898-961.png||data-xwiki-image-style-alignment="center" height="546" width="450"]]
25 +
26 +(% style="width:494px" %)
27 +|**Parameter**|(% style="width:178px" %)**Value**
28 +|Overall dimensions (length × width × height), mm|(% style="width:178px" %)120 × 120 × 17
29 +|Mounting dimensions (length × width), mm|(% style="width:178px" %)114 × 114
30 +|Mounting holes|(% style="width:178px" %)M3
31 +
32 +== Connection procedure ==
33 +
34 +The mounting area of the BMS Main 2.1 must be protected from mechanical particles (dust, dirt, large objects) and water. The installation site must provide convenient access for subsequent connection to the device’s headers.
35 +
36 +1. Connect the charging and discharging contactors to the P6-P9 headers.
37 +1. Connect a current sensor to the P12 header according to its documentation. The positive current direction (indicated by an arrow on the sensor) corresponds to the battery charging. It is recommended to use a shielded cable to connect the current sensor, the shield should be grounded on the side of the current sensor. The cable should be positioned as far as possible from the high current circuits. If the current sensor has a reference voltage line, connect it to pin 4 of the P12 header.
38 +1. Connect the BMS Main 2.1 to the on-board CAN network. Observe the rules for connecting CAN devices. If the BMS Main 2.1 is the last device on a bus, close pins 1-2 on the P21 jumper, otherwise leave the jumper on pins 2-3.
39 +1. Connect a power supply to the P1 header. It is not recommended to power the BMS Main 2.1 from the battery only, since at a critical discharge of the battery, it is not possible to turn on the BMS and close the charging contactor.
40 +
41 +== ​​​​Headers description ==
42 +
3 3  The BMS Main 2.1 headers are shown in figure below.
4 4  
5 -[[The BMS Main 2.1 headers>>image:1731516393377-928.jpeg||height="430" width="428"]]
45 +[[image:1731516393377-928.jpeg||alt="1731517946345-632.png" data-xwiki-image-style-alignment="center" height="417" width="451"]]
6 6  
47 +(% class="box warningmessage" %)
48 +(((
49 +**Attention!**
50 +All headers are shown from the device side!
51 +)))
52 +
7 7  === P1 – header for power supply ===
8 8  
9 -[[image:1731516593096-166.png||data-xwiki-image-style-alignment="center"]]
55 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
10 10  
11 -|(% style="width:100px" %)**Pin**|(% style="width:502px" %)**Name**|**Description**
12 -|(% style="width:100px" %)**1**|(% style="width:502px" %)**GND**|Ground
13 -|(% style="width:100px" %)**2**|(% style="width:502px" %)**V+**|Supply voltage 9-30V
57 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
14 14  
59 +|**Pin**|**Name**|**Description**
60 +|**1**|**GND**|Ground
61 +|**2**|**V+**|Supply voltage 9-30V
62 +
15 15  === P15 – header for BMS Logic ===
16 16  
17 -[[image:1731516577472-301.png||data-xwiki-image-style-alignment="center"]]
65 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
18 18  
19 -|(% style="width:100px" %)**Pin**|(% style="width:290px" %)**Name**|**Description**
20 -|(% style="width:100px" %)**1**|(% style="width:290px" %)**RS485_A**|RS-485 line A for communication with BMS Logic
21 -|(% style="width:100px" %)**2**|(% style="width:290px" %)**RS485_B**|RS-485 line B for communication with BMS Logic
22 -|(% style="width:100px" %)**3**|(% style="width:290px" %)**+5V**|Supply voltage for BMS Logic
23 -|(% style="width:100px" %)**4**|(% style="width:290px" %)**GND**|Ground
67 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
24 24  
69 +|**Pin**|**Name**|**Description**
70 +|**1**|**RS485_A**|RS-485 line A for communication with BMS Logic
71 +|**2**|**RS485_B**|RS-485 line B for communication with BMS Logic
72 +|**3**|**+5V**|Supply voltage for BMS Logic
73 +|**4**|**GND**|Ground
74 +
25 25  === P12 – header for current sensor ===
26 26  
27 -[[image:1731516685999-633.png||data-xwiki-image-style-alignment="center"]]
77 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
28 28  
29 -|(% style="width:100px" %)**Pin**|(% style="width:293px" %)**Name**|(% style="width:1129px" %)**Description**
30 -|(% style="width:100px" %)**1**|(% style="width:293px" %)**+5V**|(% style="width:1129px" %)Supply voltage for the current sensor 5V, max 50 mA
31 -|(% style="width:100px" %)**2**|(% style="width:293px" %)**GND**|(% style="width:1129px" %)Ground
32 -|(% style="width:100px" %)**3**|(% style="width:293px" %)**Vcs**|(% style="width:1129px" %)ADC input (current sensor output)
33 -|(% style="width:100px" %)**4**|(% style="width:293px" %)**Vref**|(% style="width:1129px" %)ADC input (current sensor reference signal)
79 +[[image:1732198890482-787.png||data-xwiki-image-style-alignment="center" height="77" width="71"]]
34 34  
81 +|**Pin**|**Name**|**Description**
82 +|**1**|**+5V**|Supply voltage for the current sensor 5V, max 50 mA
83 +|**2**|**GND**|Ground
84 +|**3**|**Vcs**|ADC input (current sensor output)
85 +|**4**|**Vref**|ADC input (current sensor reference signal)
86 +
35 35  === P13 – header for humidity sensor ===
36 36  
37 -[[image:1731516942455-641.png||data-xwiki-image-style-alignment="center"]]
89 +Receptacle Housing: Molex 430250400. Terminals: Molex 43030
38 38  
39 -|(% style="width:100px" %)**Pin**|(% style="width:292px" %)**Name**|(% style="width:1130px" %)**Description**
40 -|(% style="width:100px" %)**1**|(% style="width:292px" %)**+5V**|(% style="width:1130px" %)Supply voltage 5 V, max 50 mA
41 -|(% style="width:100px" %)**2**|(% style="width:292px" %)**GND**|(% style="width:1130px" %)Ground
42 -|(% style="width:100px" %)**3**|(% style="width:292px" %)**Vhs**|(% style="width:1130px" %)ADC input (humidity sensor output)
43 -|(% style="width:100px" %)**4**|(% style="width:292px" %)**Vts**|(% style="width:1130px" %)ADC input (temperature sensor output)
91 +[[image:1732198896526-660.png||data-xwiki-image-style-alignment="center" height="70" width="64"]]
44 44  
93 +|**Pin**|**Name**|**Description**
94 +|**1**|**+5V**|Supply voltage 5 V, max 50 mA
95 +|**2**|**GND**|Ground
96 +|**3**|**Vhs**|ADC input (humidity sensor output)
97 +|**4**|**Vts**|ADC input (temperature sensor output)
98 +
45 45  === P8 – header of relay 1 ===
46 46  
47 -[[image:1731517023208-641.png||data-xwiki-image-style-alignment="center"]]
101 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
48 48  
103 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
104 +
49 49  By default, relay 1 is used to control the discharging contactor.
50 50  
51 -|(% style="width:100px" %)**Pin**|(% style="width:291px" %)**Name**|(% style="width:1131px" %)**Description**
52 -|(% style="width:100px" %)**1**|(% style="width:291px" %)**V+**|(% style="width:1131px" %)Switching voltage (up to 55V, max 2A)
53 -|(% style="width:100px" %)**2**|(% style="width:291px" %)**NO**|(% style="width:1131px" %)Normally open contact
107 +|**Pin**|**Name**|**Description**
108 +|**1**|**V+**|Switching voltage (up to 55V, max 3A)
109 +|**2**|**NO**|Normally open contact
54 54  
111 +Contactor connection example for all relays:
112 +
113 +[[image:1741619814065-850.png||height="189" width="252"]]
114 +
55 55  === P9 – header of relay 2 ===
56 56  
57 -[[image:1731517025702-799.png||data-xwiki-image-style-alignment="center"]]
117 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
58 58  
119 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
120 +
59 59  By default, relay 2 is used to output the “Allow charging” signal.
60 60  
61 -|(% style="width:100px" %)**Pin**|(% style="width:297px" %)**Name**|(% style="width:1125px" %)**Description**
62 -|(% style="width:100px" %)**1**|(% style="width:297px" %)**V+**|(% style="width:1125px" %)Switching voltage (up to 55V, max 2A)
63 -|(% style="width:100px" %)**2**|(% style="width:297px" %)**NO**|(% style="width:1125px" %)Normally open contact
123 +|**Pin**|**Name**|**Description**
124 +|**1**|**V+**|Switching voltage (up to 55V, max 3A)
125 +|**2**|**NO**|Normally open contact
64 64  
127 +Contactor connection example: see relay 1.
128 +
65 65  === P6 – header of relay 3 ===
66 66  
67 -[[image:1731517025702-799.png||data-xwiki-image-style-alignment="center"]]
131 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
68 68  
133 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
134 +
69 69  By default, relay 3 is used to control the charging contactor.
70 70  
71 -|(% style="width:100px" %)**Pin**|(% style="width:297px" %)**Name**|(% style="width:1125px" %)**Description**
72 -|(% style="width:100px" %)**1**|(% style="width:297px" %)**V+**|(% style="width:1125px" %)Switching voltage (up to 55V, max 8A)
73 -|(% style="width:100px" %)**2**|(% style="width:297px" %)**NO**|(% style="width:1125px" %)Normally open contact
137 +|**Pin**|**Name**|**Description**
138 +|**1**|**V+**|Switching voltage up to 55V,
139 +up to 8A (board rev. 2.1b), up to 3A (board rev. 2.1c)
140 +|**2**|**NO**|Normally open contact
74 74  
142 +Contactor connection example: see relay 1.
143 +
75 75  === P7 – header of relay 4 ===
76 76  
77 -[[image:1731517025702-799.png||data-xwiki-image-style-alignment="center"]]
146 +Receptacle Housing: Molex 39012020. Terminals: Molex 5556
78 78  
148 +[[image:1732198827034-560.png||data-xwiki-image-style-alignment="center" height="78" width="41"]]
149 +
79 79  By default, relay 4 is used to control the heater.
80 80  
81 -|(% style="width:100px" %)**Pin**|(% style="width:298px" %)**Name**|(% style="width:1124px" %)**Description**
82 -|(% style="width:100px" %)**1**|(% style="width:298px" %)**V+**|(% style="width:1124px" %)Switching voltage (up to 55V, max 8A)
83 -|(% style="width:100px" %)**2**|(% style="width:298px" %)**NO**|(% style="width:1124px" %)Normally open contact
152 +|**Pin**|**Name**|**Description**
153 +|**1**|**V+**|Switching voltage up to 55V,
154 +up to 8A (board rev. 2.1b), up to 3A (board rev. 2.1c)
155 +|**2**|**NO**|Normally open contact
84 84  
157 +Contactor connection example: see relay 1.
158 +
85 85  === P14 – header for CAN and RS-485 interfaces ===
86 86  
87 -[[image:1731517180930-597.png||data-xwiki-image-style-alignment="center"]]
161 +Receptacle Housing: Molex 430250600. Terminals: Molex 43030
88 88  
89 -|(% style="width:100px" %)**Pin**|**Name**|**Description**
90 -|(% style="width:100px" %)**1**|**EXT_RS485_A**|RS-485 line A for communication with external equipment
91 -|(% style="width:100px" %)**2**|**CAN_H**|CAN H line for communication with external equipment
92 -|(% style="width:100px" %)**3**|**+5V_CAN**|Supply voltage 5V for external devices, max 200 mA
93 -|(% style="width:100px" %)**4**|**EXT_RS485_B**|RS-485 line B for communication with external equipment
94 -|(% style="width:100px" %)**5**|**CAN_L**|CAN L line for communication with external equipment
95 -|(% style="width:100px" %)**6**|**GND_CAN**|Ground
163 +[[image:1731517180930-597.png||data-xwiki-image-style-alignment="center" height="81" width="113"]]
96 96  
165 +(% style="width:641px" %)
166 +|**Pin**|**Name**|**Description**
167 +|**1**|**EXT_RS485_A**|RS-485 line A for communication with external equipment
168 +|**2**|**CAN_H**|CAN H line for communication with external equipment
169 +|**3**|**+5V_CAN**|Supply voltage 5V for external devices, max 200 mA
170 +|**4**|**EXT_RS485_B**|RS-485 line B for communication with external equipment
171 +|**5**|**CAN_L**|CAN L line for communication with external equipment
172 +|**6**|**GND_CAN**|Ground
173 +
97 97  === P21 – CAN termination resistor jumper ===
98 98  
99 -[[image:1731517188900-976.png||data-xwiki-image-style-alignment="center"]]
176 +[[image:1731517188900-976.png||data-xwiki-image-style-alignment="center" height="78" width="149"]]
100 100  
101 101  To connect the termination resistor between the lines **CAN_H** and **CAN_L**, install a jumper, according to the P21 pinout:
102 102  
103 -|(% style="width:100px" %)**Pin**|(% style="width:299px" %)**Name**|(% style="width:1123px" %)**Description**
104 -|(% style="width:100px" %)**1-2**|(% style="width:299px" %)**120 Ohm**|(% style="width:1123px" %)Termination resistor 120 Ohm is connected
105 -|(% style="width:100px" %)**2-3**|(% style="width:299px" %)**-**|(% style="width:1123px" %)Termination resistor 120 Ohm is not connected
180 +|**Pin**|**Name**|**Description**
181 +|**1-2**|**120 Ohm**|Termination resistor 120 Ohm is connected
182 +|**2-3**|**-**|Termination resistor 120 Ohm is not connected
106 106  
107 107  === P22 - RS-485 termination resistor jumper ===
108 108  
109 -[[image:1731517195672-298.png||data-xwiki-image-style-alignment="center"]]
186 +[[image:1731517195672-298.png||data-xwiki-image-style-alignment="center" height="81" width="155"]]
110 110  
111 111  To connect the termination resistor between the **EXT_RS485_A** and **EXT_RS485_B** lines, install a jumper according to the P22 pinout:
112 112  
113 -|(% style="width:100px" %)**Pin**|(% style="width:301px" %)**Name**|(% style="width:1121px" %)**Description**
114 -|(% style="width:100px" %)**1-2**|(% style="width:301px" %)**120 Ohm**|(% style="width:1121px" %)Terminating resistor 120 Ohm is connected
115 -|(% style="width:100px" %)**2-3**|(% style="width:301px" %)**-**|(% style="width:1121px" %)Terminating resistor 120 Ohm is not connected
190 +|**Pin**|**Name**|**Description**
191 +|**1-2**|**120 Ohm**|Terminating resistor 120 Ohm is connected
192 +|**2-3**|**-**|Terminating resistor 120 Ohm is not connected
116 116  
117 117  === P11 – header for discrete inputs/outputs ===
118 118  
119 -[[image:1731517206246-979.png||data-xwiki-image-style-alignment="center"]]
196 +Receptacle Housing: Molex 430251600. Terminals: Molex 43030
120 120  
121 -|(% style="width:100px" %)**Pin**|(% style="width:310px" %)**Name**|(% style="width:1112px" %)**Description**
122 -|(% style="width:100px" %)**16**|(% style="width:310px" %)**IN_1**|(% style="width:1112px" %)Discrete input #1 “dry contact” (+5V)
123 -|(% style="width:100px" %)**8**|(% style="width:310px" %)**GND_1**|(% style="width:1112px" %)Discrete input #1 “dry contact” (ground)
124 -|(% style="width:100px" %)**15**|(% style="width:310px" %)**IN_2**|(% style="width:1112px" %)Discrete input #2 “dry contact” (+5V)
125 -|(% style="width:100px" %)**7**|(% style="width:310px" %)**GND_2**|(% style="width:1112px" %)Discrete input #2 “dry contact” (ground)
126 -|(% style="width:100px" %)**14**|(% style="width:310px" %)**IN_3**|(% style="width:1112px" %)Discrete input #3 “dry contact” (+5V)
127 -|(% style="width:100px" %)**6**|(% style="width:310px" %)**GND_3**|(% style="width:1112px" %)Discrete input #3 “dry contact” (ground)
128 -|(% style="width:100px" %)**13**|(% style="width:310px" %)**IN_4**|(% style="width:1112px" %)Discrete input #4 “dry contact” (+5V)
129 -|(% style="width:100px" %)**5**|(% style="width:310px" %)**GND_4**|(% style="width:1112px" %)Discrete input #4 “dry contact” (ground)
130 -|(% style="width:100px" %)**12**|(% style="width:310px" %)**OUT_4**|(% style="width:1112px" %)Discrete output #4 (+5V, 20mA)
131 -|(% style="width:100px" %)**4**|(% style="width:310px" %)**GND_OUT_4**|(% style="width:1112px" %)Discrete output #4 (ground)
132 -|(% style="width:100px" %)**11**|(% style="width:310px" %)**OUT_3**|(% style="width:1112px" %)Discrete output #3 (+5V, 20mA)
133 -|(% style="width:100px" %)**3**|(% style="width:310px" %)**GND_OUT_3**|(% style="width:1112px" %)Discrete output #3 (ground)
134 -|(% style="width:100px" %)**10**|(% style="width:310px" %)**OUT_2**|(% style="width:1112px" %)Discrete output #2 (+5V, 20mA)
135 -|(% style="width:100px" %)**2**|(% style="width:310px" %)**GND_OUT_2**|(% style="width:1112px" %)Discrete output #2 (ground)
136 -|(% style="width:100px" %)**9**|(% style="width:310px" %)**OUT_1**|(% style="width:1112px" %)Discrete output #1 (+5V, 20mA)
137 -|(% style="width:100px" %)**1**|(% style="width:310px" %)**GND_OUT_1**|(% style="width:1112px" %)Discrete output #1 (ground)
198 +[[image:1732198937514-731.png||data-xwiki-image-style-alignment="center" height="85" width="272"]]
138 138  
139 -= Indicators =
200 +|**Pin**|**Name**|**Description**
201 +|**16**|**IN_1**|Discrete input #1 “dry contact” (+5V)
202 +|**8**|**GND_1**|Discrete input #1 “dry contact” (ground)
203 +|**15**|**IN_2**|Discrete input #2 “dry contact” (+5V)
204 +|**7**|**GND_2**|Discrete input #2 “dry contact” (ground)
205 +|**14**|**IN_3**|Discrete input #3 “dry contact” (+5V)
206 +|**6**|**GND_3**|Discrete input #3 “dry contact” (ground)
207 +|**13**|**IN_4**|Discrete input #4 “dry contact” (+5V)
208 +|**5**|**GND_4**|Discrete input #4 “dry contact” (ground)
209 +|**12**|**OUT_4**|Discrete output #4 (+5V, 20mA)
210 +|**4**|**GND_OUT_4**|Discrete output #4 (ground)
211 +|**11**|**OUT_3**|Discrete output #3 (+5V, 20mA)
212 +|**3**|**GND_OUT_3**|Discrete output #3 (ground)
213 +|**10**|**OUT_2**|Discrete output #2 (+5V, 20mA)
214 +|**2**|**GND_OUT_2**|Discrete output #2 (ground)
215 +|**9**|**OUT_1**|Discrete output #1 (+5V, 20mA)
216 +|**1**|**GND_OUT_1**|Discrete output #1 (ground)
140 140  
218 +== Indicators ==
219 +
141 141  === DS1 – power indicator ===
142 142  
143 -|(% style="width:100px" %)**State**|**Description**
144 -|(% style="width:100px" %)**Lights red**|The device is powered
145 -|(% style="width:100px" %)**Off**|The device is not powered
222 +|**State**|**Description**
223 +|**Lights red**|The device is powered
224 +|**Off**|The device is not powered
146 146  
147 147  === DS2 – operation indicator ===
148 148  
149 -|(% style="width:100px" %)**State**|**Description**
150 -|(% style="width:100px" %)**Blinking green**|The BMS firmware is running
151 -|(% style="width:100px" %)**Off**|The BMS firmware is not running
228 +|**State**|**Description**
229 +|**Blinking green**|The BMS firmware is running
230 +|**Off**|The BMS firmware is not running
152 152  
153 153  === DS3 – communication indicator ===
154 154  
155 -|(% style="width:100px" %)**State**|**Description**
156 -|(% style="width:100px" %)**Blinking yellow (2Hz)**|Initializing communication with BMS Logic boards
157 -|(% style="width:100px" %)**Blinking yellow (25Hz)**|Communication with BMS Logic is established
234 +|**State**|**Description**
235 +|**Blinking yellow (2Hz)**|Initializing communication with BMS Logic boards
236 +|**Blinking yellow (25Hz)**|Communication with BMS Logic is established
158 158  
159 159  === DS4 – error indicator ===
160 160  
161 -|(% style="width:100px" %)**State**|**Description**
162 -|(% style="width:100px" %)**Blinking red**|Errors in communication with BMS Logic
163 163  
241 +|(**State**|**Description**
242 +|(**Blinking red**|Errors in communication with BMS Logic
243 +
164 164  === DS7 – relay 1 indicator ===
165 165  
166 -|(% style="width:100px" %)**State**|**Description**
167 -|(% style="width:100px" %)**Lights green**|Relay #1 is closed
168 -|(% style="width:100px" %)**Off**|Relay #1 is opened
246 +|**State**|**Description**
247 +|**Lights green**|Relay #1 is closed
248 +|**Off**|Relay #1 is opened
169 169  
170 170  === DS8 – relay 2 indicator ===
171 171  
172 -|(% style="width:100px" %)**State**|**Description**
173 -|(% style="width:100px" %)**Lights green**|Relay #2 is closed
174 -|(% style="width:100px" %)**Off**|Relay #2 is opened
252 +|**State**|**Description**
253 +|**Lights green**|Relay #2 is closed
254 +|**Off**|Relay #2 is opened
175 175  
176 176  === DS5 – relay 3 indicator ===
177 177  
178 -|(% style="width:100px" %)**State**|**Description**
179 -|(% style="width:100px" %)**Lights green**|Relay #3 is closed
180 -|(% style="width:100px" %)**Off**|Relay #3 is opened
258 +|**State**|**Description**
259 +|**Lights green**|Relay #3 is closed
260 +|**Off**|Relay #3 is opened
181 181  
182 182  === DS6 – relay 4 indicator ===
183 183  
184 -|(% style="width:100px" %)**State**|**Description**
185 -|(% style="width:100px" %)**Lights green**|Relay #4 is closed
186 -|(% style="width:100px" %)**Off**|Relay #4 is opened
264 +|**State**|**Description**
265 +|**Lights green**|Relay #4 is closed
266 +|**Off**|Relay #4 is opened
187 187  
188 188  
1731516474613-418.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731516577472-301.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731516593096-166.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731516685999-633.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731516942455-641.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -1.5 KB
Content
1731517023208-641.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731517025702-799.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -981 bytes
Content
1731517206246-979.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -4.2 KB
Content
1732198397369-222.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +81.3 KB
Content
1732198827034-560.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +1.1 KB
Content
1732198890482-787.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 KB
Content
1732198896526-660.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +2.0 KB
Content
1732198937514-731.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +7.1 KB
Content
1741619628288-759.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +29.2 KB
Content
1741619637854-961.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +29.2 KB
Content
1741619700532-367.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +14.1 KB
Content
1741619814065-850.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +15.1 KB
Content
1741620022836-867.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +13.3 KB
Content
1752600650898-961.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +84.9 KB
Content