Skip to Content
Last modified by Admin on 2025/03/18 13:04
From version 11.1
edited by Admin
on 2025/03/18 12:28
Change comment: There is no comment for this version
To version 9.1
edited by Admin
on 2025/02/20 12:08
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,19 +1,8 @@
1 1  (% data-numbered-headings-start="2" style="--numbered-headings-start: 1;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 2  = Installation and connection =
3 3  
4 -== ​​​​​Safety rules ==
4 +== ​​​​​Installation procedure ==
5 5  
6 -Before use, **configure the system**. Proper operation of the BMS is possible only if it is correctly configured.
7 -
8 -It is not recommended to use the system in batteries formed by several series of cells connected in parallel. To increase capacity, it is recommended to connect several cells in parallel groups, and then connect the groups in series.
9 -
10 -(% class="box warningmessage" %)
11 -(((
12 -The BMS can be connected to batteries with life-threatening and health-hazardous voltage levels. When working with high-voltage batteries, observe electrical safety regulations, use safety glasses, protective clothing, insulated tools and appliances. To prevent the damage of device avoid electrostatic discharges while working with the battery.
13 -)))
14 -
15 -== Installation procedure ==
16 -
17 17  The mounting area of the BMS Logic 2.0 must be protected from mechanical particles (dust, dirt, large objects) and water. The BMS Logic 2.0 is recommended to be placed close to the cells it controls, but away from high current circuits to reduce interference to measuring circuits and increase overall reliability of installation.
18 18  
19 19  The installation site must provide convenient access for subsequent connection to the device’s headers.
... ... @@ -30,6 +30,7 @@
30 30  )))|125 × 84 × 25
31 31  |Mounting dimensions (length × width), mm|115 × 50
32 32  |Mounting holes|M4
22 +|Headers X1-X3 type|Molex series Mini-Fit
33 33  
34 34  == Headers ==
35 35  
... ... @@ -43,21 +43,8 @@
43 43  All headers are shown from the device side!
44 44  )))
45 45  
46 -=== X1 – header for cells and temperature sensors ===
36 +=== X1 – header for cells and temperature sensors[[image:1740053130023-265.png||data-xwiki-image-style-alignment="center"]] ===
47 47  
48 -(% class="wikigeneratedid" %)
49 -Receptacle Housing: Molex 39012160. Terminals: Molex 5556
50 -
51 -
52 -
53 -
54 -
55 -
56 -
57 -
58 -(% class="wikigeneratedid" %)
59 -[[image:1740053130023-265.png||data-xwiki-image-style-alignment="center"]]
60 -
61 61  |**Pin**|**Name**|**Description**
62 62  |**1**|**TEMP2**|Signal from the thermistor #2
63 63  |**2**|**TEMPC**|Ground of the thermistors
... ... @@ -78,8 +78,6 @@
78 78  
79 79  === X2, X3 – headers for communication with BMS Main ===
80 80  
81 -Receptacle Housing: Molex 39012040. Terminals: Molex 5556
82 -
83 83  [[image:1740053153731-112.png||data-xwiki-image-style-alignment="center"]]
84 84  
85 85  |**Pin**|**Name**|**Description**