Skip to Content
Last modified by Admin on 2025/03/18 13:04
From version 8.1
edited by Admin
on 2024/12/04 11:25
Change comment: There is no comment for this version
To version 3.1
edited by Admin
on 2024/12/02 14:57
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -24,12 +24,6 @@
24 24  
25 25  [[image:1733150257403-684.png||data-xwiki-image-style-alignment="center" height="376" width="640"]]
26 26  
27 -(% class="box warningmessage" %)
28 -(((
29 -**Attention!**
30 -All connectors are shown from the device side!
31 -)))
32 -
33 33  === 2.2.1 X1 – header for cells ===
34 34  
35 35  [[image:1733150257406-647.jpeg||data-xwiki-image-style-alignment="center" height="73" width="256"]]
... ... @@ -127,7 +127,7 @@
127 127  
128 128  (% class="box infomessage" %)
129 129  (((
130 -**Note: **There is no SWD1 switch in the recent revisions of the BMS Logic 18. The device address must be configured in the settings (see the section [[3. Configuration>>doc:drafts.BMS Logic 18.3\. Configuration.WebHome]]).
124 +**Note: **There is no SWD1 switch in the recent revisions of the BMS Logic 18. The device address must be configured in the settings (see the section 4.2 Configuration procedure).
131 131  )))
132 132  
133 133  === 2.4.2 SWD2 – RS-485 termination resistor switch ===
... ... @@ -141,11 +141,10 @@
141 141  
142 142  === 2.4.3 DS1 – mode indicator ===
143 143  
144 -(% style="width:551px" %)
145 -|(% style="width:188px" %)**State**|(% style="width:362px" %)**Description**
146 -|(% style="width:188px" %)**Blinking**|(% style="width:362px" %)Connection between the BMS Main and the device is established
147 -|(% style="width:188px" %)**Short flashing (~~50 milliseconds in a second)**|(% style="width:362px" %)The device is measuring voltage and temperature. No communication between the BMS Main and the device
148 -|(% style="width:188px" %)**Long flashing (1 second in a 2 second period)**|(% style="width:362px" %)The device is in the bootloader mode
138 +|**State**|**Description**
139 +|**Blinking**|Connection between the BMS Main and the device is established
140 +|**Short flashing (~~50 milliseconds in a second)**|The device is measuring voltage and temperature. No communication between the BMS Main and the device
141 +|**Long flashing (1 second in a 2 second period)**|The device is in the bootloader mode
149 149  
150 150  == 2.5 Connection procedure ==
151 151  
... ... @@ -183,7 +183,3 @@
183 183  === 2.5.3 Connecting thermistors ===
184 184  
185 185  Thermistors should be fastened to the cells, excluding short circuits to the cell terminals (for example, isolate thermistors with heat shrink). For reliable operation, it is recommended to use all thermistors (a temperature sensor per cell).
186 -
187 -[[image:1733231170607-745.png||data-xwiki-image-style-alignment="center" height="324" width="806"]]
188 -
189 -
1733231170607-745.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -254.4 KB
Content