Skip to Content

Wiki source code of 3. Configuration

Version 6.1 by Admin on 2024/12/02 13:28
Hide last authors
Admin 1.1 1 == 3.1 Connecting device to PC ==
2
3 To connect the BMS Logic 12 to a PC, use the BMS USB-RS485 adapter. It allows to power and communicate with the BMS Logic 12:
4
5 1. Connect the BMS USB-RS485 to the BMS Logic 12:
6 a) the communication circuits (X3 -> X3);
7 b) the circuits of cells (X5 -> X1).
8 1. Connect the BMS USB-RS485 to a PC using a mini-USB or USB-C cable.
9 1. Turn all the BMS USB-RS485’s switches to the “I” position.
10
11 The assembly drawings of the harnesses between the BMS USB-RS485 and BMS Logic 12 are give below.
12
13 === 3.1.1 Communication and power cable ===
14
Admin 6.1 15 [[image:1733145551342-738.png||data-xwiki-image-style-alignment="center" height="206" width="375"]]
Admin 1.1 16
17 The wires of the communication and power cable must be connected according to the following table:
18
19 (% style="width:398px" %)
20 |**Circuit name**|(% style="width:149px" %)**Pin of the connector to BMS USB-RS485**|(% style="width:153px" %)**Pin of the connector to BMS Logic 12**
21 |**RS485_A**|(% style="width:149px" %)1|(% style="width:153px" %)1
22 |**RS485_B**|(% style="width:149px" %)2|(% style="width:153px" %)2
23 |**+5V**|(% style="width:149px" %)3|(% style="width:153px" %)3
24 |**GND**|(% style="width:149px" %)4|(% style="width:153px" %)4
25
26 === 3.1.2 Cells cable ===
27
Admin 6.1 28 [[image:1733145551344-998.png||data-xwiki-image-style-alignment="center" height="100" width="456"]]
Admin 1.1 29
Admin 6.1 30 [[image:1733145551345-310.png||data-xwiki-image-style-alignment="center" height="217" width="425"]]
Admin 1.1 31
32
33 The wires of the cells cable must be connected according to the following table:
34
35 (% style="width:393px" %)
36 |**Circuit name**|(% style="width:148px" %)**Pin of the connector to BMS USB-RS485**|(% style="width:149px" %)**Pin of the connector to BMS Logic 12**
37 |**V-**|(% style="width:148px" %)1|(% style="width:149px" %)1
38 |**C1**|(% style="width:148px" %)13|(% style="width:149px" %)9
39 |**C2**|(% style="width:148px" %)2|(% style="width:149px" %)2
40 |**C3**|(% style="width:148px" %)14|(% style="width:149px" %)10
41 |**C4**|(% style="width:148px" %)3|(% style="width:149px" %)3
42 |**C5**|(% style="width:148px" %)15|(% style="width:149px" %)11
43 |**C6**|(% style="width:148px" %)4|(% style="width:149px" %)4
44 |**C7**|(% style="width:148px" %)5|(% style="width:149px" %)12
45 |**C8**|(% style="width:148px" %)6|(% style="width:149px" %)5
46 |**C9**|(% style="width:148px" %)7|(% style="width:149px" %)13
47 |**C10**|(% style="width:148px" %)8|(% style="width:149px" %)6
48 |**C11**|(% style="width:148px" %)9|(% style="width:149px" %)14
49 |**C12**|(% style="width:148px" %)10|(% style="width:149px" %)7
50
51 === 3.2 Setting the device address ===
52
53 Launch the ElectricDeviceMonitor, then select the “BMS Logic 12/18 3.x” monitor:
54
55 [[image:1733145551346-396.png||data-xwiki-image-style-alignment="center" height="324" width="296"]]
56
57
Admin 2.1 58 Set the following settings to connect to the BMS Logic 12:
Admin 1.1 59
Admin 2.1 60 * 115200 bps,
61 * 8 bits,
62 * no parity,
63 * 1 stop bit,
64 * device address 247.
65
66 The address 247 is a service address that the device will always answer.
67
Admin 1.1 68 [[image:1733145551347-494.png||data-xwiki-image-style-alignment="center" height="242" width="439"]]
69
70 Check the connection with the BMS Logic 12 is established.
71
72 Set the needed device address and click the “Save” button:
73
Admin 3.1 74 [[image:1733145551348-226.png||data-xwiki-image-style-alignment="center" height="444" width="682"]]
Admin 5.1 75
76