Skip to Content

Wiki source code of 5. Firmware update

Version 6.8 by Admin on 2025/02/28 10:59
Show last authors
1 (% data-numbered-headings-start="4" style="--numbered-headings-start: 3;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 = Firmware update =
3
4 == Introduction ==
5
6 The document describes the steps to update the BMS Display firmware.
7
8 Required hardware and software:
9
10 * PC or laptop with Windows 10 or newer;
11 * BMS USB-CAN adapter – a device to power up and communicate with the BMS Display;
12 ** Also Systec, PEAK and Marathon USB-CAN adapters are supported, but
13 * [[ElectricDeviceMonitor>>https://movicomelectric.com/wa-data/public/site/app/ElectricDeviceMonitorSETUP.exe]] – a software to monitor and configure devices by Movicom Electric;
14 * Firmware (*.srec) – a new firmware for the BMS Display.
15
16 == Updating process ==
17
18 Follow the steps below:
19
20 ~1. Connect the BMS Display to the USB-CAN adapter.
21
22 2. Move switches of the to the following positions:
23
24 * 120 Ohm – “I”;
25 * +5V – “0”.
26
27 3. Connect the USB-CAN adapter to a PC.
28
29 4. Move the switch “+5V” of the BMS USB-CAN to “I”. Check that the led of the BMS Display is blinking.
30
31 5. Open the Device Manager* and determine a name of an appeared serial port (Click the right mouse button on the Start menu and select the “Device Manager” item):
32
33 [[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153285-215.png||data-xwiki-image-style-alignment="center" height="377" width="382"]]
34
35 6. Install and launch the ElectricDeviceMonitor.
36
37 7. Click the “Updater” button:
38
39 [[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153290-392.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
40
41 8. Select the CAN transport (BMS USB-CAN) (1.0.0) and click the “Settings” button to configure the adapter: select port name that corresponds to the BMS USB-CAN adapter and 250 kbit/s baud rate.
42
43 [[image:1740738923079-336.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
44
45 9. Click the “Browse…” button and open the new firmware file in .srec format.
46
47 **10. Boot the device to go into the bootloader mode.**
48
49 * In the ElectricDeviceMonitor, select the menu “Tasks – Monitor - BMS Display 1.x”:
50
51 [[image:1740739041707-667.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="295" width="300"]]
52
53 * Set the following connection settings and click the “Launch” button:
54 ** port name that corresponds to the BMS USB-CAN adapter;
55 ** baud rate: 250 kbit/s;
56 ** BMS Display Node ID (20 by default).
57
58 [[image:1740739961052-896.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="237" width="450"]]
59
60 * In the opened window, click the “Send” button under "Reset and start bootloader" section. The device will reboot and will be waiting commands to update the firmware.
61
62 [[image:1740740038720-603.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="553" width="600"]]
63
64 * **Select the menu “Monitor - Stop” or click the “Stop” button to release the serial port and allow to use it for updating the firmware.**
65
66 ~11. Return to the “Updater” window and click the “Update” button. The updating process will start.
67
68 12. Wait the updating process is finished. Move the “+5V” switch to the “0” position. and disconnect the BMS Display device from the BMS USB-CAN adapter.