Skip to Content

Changes for page 5. Firmware update

Last modified by Admin on 2025/02/28 11:48
From version 8.1
edited by Admin
on 2025/02/28 11:00
Change comment: There is no comment for this version
To version 13.2
edited by Admin
on 2025/02/28 11:32
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -Battery management systems.BMS Display.WebHome
1 +Battery management systems.BMS IMD.WebHome
Content
... ... @@ -3,23 +3,23 @@
3 3  
4 4  == Introduction ==
5 5  
6 -The document describes the steps to update the BMS Display firmware.
6 +The document describes the steps to update the BMS IMD firmware.
7 7  
8 8  Required hardware and software:
9 9  
10 10  * PC or laptop with Windows 10 or newer;
11 -* BMS USB-CAN adapter – a device to power up and communicate with the BMS Display;
12 -** Also Systec, PEAK and Marathon USB-CAN adapters are supported, but external power supply for BMS Display is needed;
11 +* BMS USB-CAN – a device to power up and communicate with the BMS IMD;
12 +** Also Systec, PEAK and Marathon USB-CAN adapters are supported;
13 13  * [[ElectricDeviceMonitor>>https://movicomelectric.com/wa-data/public/site/app/ElectricDeviceMonitorSETUP.exe]] – a software to monitor and configure devices by Movicom Electric;
14 -* Firmware (*.srec) – a new firmware for the BMS Display.
14 +* Firmware (*.srec) – a new firmware for the BMS IMD.
15 15  
16 16  == Updating process ==
17 17  
18 18  Follow the steps below:
19 19  
20 -~1. Connect the BMS Display to the USB-CAN adapter.
20 +~1. Connect the BMS IMD to the USB-CAN adapter.
21 21  
22 -2. Move switches of the to the following positions:
22 +2. Move switches of the  to the following positions:
23 23  
24 24  * 120 Ohm – “I”;
25 25  * +5V – “0”.
... ... @@ -26,7 +26,7 @@
26 26  
27 27  3. Connect the USB-CAN adapter to a PC.
28 28  
29 -4. Move the switch “+5V” of the BMS USB-CAN to “I”. Check that the led of the BMS Display is blinking.
29 +4. Move the switch “+5V” of the BMS USB-CAN to “I”. Check that the led of the BMS IMD is blinking.
30 30  
31 31  5. Open the Device Manager* and determine a name of an appeared serial port (Click the right mouse button on the Start menu and select the “Device Manager” item):
32 32  
... ... @@ -38,8 +38,11 @@
38 38  
39 39  [[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153290-392.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
40 40  
41 -8. Select the CAN transport (BMS USB-CAN) (1.0.0) and click the “Settings” button to configure the adapter: select port name that corresponds to the BMS USB-CAN adapter and 250 kbit/s baud rate.
41 +8. Select the "CAN transport (BMS USB-CAN) (1.0.0)" in a drop-down list and click the “Settings” button to configure the adapter:
42 42  
43 +* select port name that corresponds to the BMS USB-CAN;
44 +* set 250 kbit/s baud rate.
45 +
43 43  [[image:1740738923079-336.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
44 44  
45 45  9. Click the “Browse…” button and open the new firmware file in .srec format.
... ... @@ -46,14 +46,14 @@
46 46  
47 47  **10. Boot the device to go into the bootloader mode.**
48 48  
49 -* In the ElectricDeviceMonitor, select the menu “Tasks – Monitor - BMS Display 1.x”:
52 +* In the ElectricDeviceMonitor, select the menu “Tasks – Monitor - BMS IMD 1.x”:
50 50  
51 51  [[image:1740739041707-667.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="295" width="300"]]
52 52  
53 53  * Set the following connection settings and click the “Launch” button:
54 -** port name that corresponds to the BMS USB-CAN adapter;
57 +** port name that corresponds to the BMS USB-CAN;
55 55  ** baud rate: 250 kbit/s;
56 -** BMS Display Node ID (20 by default).
59 +** BMS IMD Node ID (20 by default).
57 57  
58 58  [[image:1740739961052-896.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="237" width="450"]]
59 59  
... ... @@ -65,4 +65,4 @@
65 65  
66 66  ~11. Return to the “Updater” window and click the “Update” button. The updating process will start.
67 67  
68 -12. Wait the updating process is finished. Move the “+5V” switch to the “0” position. and disconnect the BMS Display device from the BMS USB-CAN adapter.
71 +12. Wait the updating process is finished. Move the “+5V” switch to the “0” position. and disconnect the BMS IMD device from the BMS USB-CAN.
1740741924108-471.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +15.7 KB
Content
1740742073165-496.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.admin
Size
... ... @@ -1,0 +1,1 @@
1 +45.3 KB
Content