Skip to Content

Changes for page 5. Firmware update

Last modified by Admin on 2025/02/28 11:48
From version 7.1
edited by Admin
on 2025/02/28 11:00
Change comment: There is no comment for this version
To version 5.2
edited by Admin
on 2025/02/28 10:53
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -8,8 +8,7 @@
8 8  Required hardware and software:
9 9  
10 10  * PC or laptop with Windows 10 or newer;
11 -* BMS USB-CAN adapter – a device to power up and communicate with the BMS Display;
12 -** Also Systec, PEAK and Marathon USB-CAN adapters are supported, but external power supply for BMS Display is needed;
11 +* BMS USB-CAN – a device to power and communicate with the BMS Display;
13 13  * [[ElectricDeviceMonitor>>https://movicomelectric.com/wa-data/public/site/app/ElectricDeviceMonitorSETUP.exe]] – a software to monitor and configure devices by Movicom Electric;
14 14  * Firmware (*.srec) – a new firmware for the BMS Display.
15 15  
... ... @@ -19,7 +19,7 @@
19 19  
20 20  ~1. Connect the BMS Display to the USB-CAN adapter.
21 21  
22 -2. Move switches of the to the following positions:
21 +2. If BMS USB-CAN used, move switches of the to the following positions:
23 23  
24 24  * 120 Ohm – “I”;
25 25  * +5V – “0”.
... ... @@ -26,7 +26,7 @@
26 26  
27 27  3. Connect the USB-CAN adapter to a PC.
28 28  
29 -4. Move the switch “+5V” of the BMS USB-CAN to “I”. Check that the led of the BMS Display is blinking.
28 +4. If BMS USB-CAN used, move the switch “+5V” of the BMS USB-CAN to “I”. Otherwise power up the BMS Display. Check that the led of the BMS Display is blinking.
30 30  
31 31  5. Open the Device Manager* and determine a name of an appeared serial port (Click the right mouse button on the Start menu and select the “Device Manager” item):
32 32  
... ... @@ -38,7 +38,7 @@
38 38  
39 39  [[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153290-392.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
40 40  
41 -8. Select the CAN transport (BMS USB-CAN) (1.0.0) and click the “Settings” button to configure the adapter: select port name that corresponds to the BMS USB-CAN adapter and 250 kbit/s baud rate.
40 +8. Select the corresponding CAN transport and click the “Settings” button to configure the adapter: select device or port name that corresponds to the USB-CAN adapter and 250 kbit/s baud rate.
42 42  
43 43  [[image:1740738923079-336.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
44 44  
... ... @@ -51,18 +51,18 @@
51 51  [[image:1740739041707-667.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="295" width="300"]]
52 52  
53 53  * Set the following connection settings and click the “Launch” button:
54 -** port name that corresponds to the BMS USB-CAN adapter;
53 +** device or port name that corresponds to the USB-CAN adapter;
55 55  ** baud rate: 250 kbit/s;
56 56  ** BMS Display Node ID (20 by default).
57 57  
58 58  [[image:1740739961052-896.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="237" width="450"]]
59 59  
60 -* In the opened window, click the “Send” button under "Reset and start bootloader" section. The device will reboot and will be waiting commands to update the firmware.
59 +* In the opened window, click the “Send” button. The device will reboot and will be waiting commands to update the firmware.
61 61  
62 -[[image:1740740038720-603.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="553" width="600"]]
61 +[[image:1733156153294-767.png||data-xwiki-image-style-alignment="center" height="425" width="648"]]
63 63  
64 64  * **Select the menu “Monitor - Stop” or click the “Stop” button to release the serial port and allow to use it for updating the firmware.**
65 65  
66 66  ~11. Return to the “Updater” window and click the “Update” button. The updating process will start.
67 67  
68 -12. Wait the updating process is finished. Move the “+5V” switch to the “0” position. and disconnect the BMS Display device from the BMS USB-CAN adapter.
67 +12. Wait the updating process is finished. Move the switches “+5V” and “Cells” to the “0” position and disconnect the BMS Logic device from the BMS USB-RS485.
1740740038720-603.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -49.9 KB
Content