Skip to Content

Changes for page 5. Firmware update

Last modified by Admin on 2025/02/28 11:48
From version 6.4
edited by Admin
on 2025/02/28 10:55
Change comment: There is no comment for this version
To version 4.8
edited by Admin
on 2025/02/28 10:39
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -8,7 +8,7 @@
8 8  Required hardware and software:
9 9  
10 10  * PC or laptop with Windows 10 or newer;
11 -* USB-CAN adapter – a device to communicate with the BMS Display;
11 +* BMS USB-CAN – a device to power and communicate with the BMS Display;
12 12  * [[ElectricDeviceMonitor>>https://movicomelectric.com/wa-data/public/site/app/ElectricDeviceMonitorSETUP.exe]] – a software to monitor and configure devices by Movicom Electric;
13 13  * Firmware (*.srec) – a new firmware for the BMS Display.
14 14  
... ... @@ -16,14 +16,16 @@
16 16  
17 17  Follow the steps below:
18 18  
19 -~1. Connect the BMS Display to the USB-CAN adapter. If BMS USB-CAN used, move switches of the to the following positions:
19 +~1. Connect the BMS Display to the USB-CAN adapter.
20 20  
21 +2. If BMS USB-CAN used, move switches of the to the following positions:
22 +
21 21  * 120 Ohm – “I”;
22 22  * +5V – “0”.
23 23  
24 -2. Connect the USB-CAN adapter to a PC.
26 +3. Connect the USB-CAN adapter to a PC.
25 25  
26 -4. If BMS USB-CAN used, move the switch “+5V” of the BMS USB-CAN to “I”. Otherwise power up the BMS Display. Check that the led of the BMS Display is blinking.
28 +4. If BMS USB-CAN used, move the switch “+5V” of the BMS USB-CAN to “I”. Otherwise power up the BMS DiCheck that the led of the BMS Display is blinking.
27 27  
28 28  5. Open the Device Manager* and determine a name of an appeared serial port (Click the right mouse button on the Start menu and select the “Device Manager” item):
29 29  
... ... @@ -35,7 +35,7 @@
35 35  
36 36  [[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153290-392.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
37 37  
38 -8. Select the corresponding CAN transport and click the “Settings” button to configure the adapter: select device or port name that corresponds to the USB-CAN adapter and 250 kbit/s baud rate.
40 +8. Select the transport “CAN transport (BMS USB-CAN) (1.0.0)” and click the “Settings” button to configure the adapter: select a port name that corresponds to the BMS USB-CAN and 250 kbit/s baud rate.
39 39  
40 40  [[image:1740738923079-336.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
41 41  
... ... @@ -48,18 +48,18 @@
48 48  [[image:1740739041707-667.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="295" width="300"]]
49 49  
50 50  * Set the following connection settings and click the “Launch” button:
51 -** device or port name that corresponds to the USB-CAN adapter;
52 -** baud rate: 250 kbit/s;
53 -** BMS Display Node ID (20 by default).
53 +** serial port name of the BMS USB-RS485
54 +** baud rate and data format: 115200 kbps, 8 bits, no parity, 1 stop bit
55 +** address – 247
54 54  
55 -[[image:1740739961052-896.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="237" width="450"]]
57 +[[image:1733156153293-550.png||data-xwiki-image-style-alignment="center" height="227" width="410"]]
56 56  
57 -* In the opened window, click the “Send” button under "Reset and start bootloader" section. The device will reboot and will be waiting commands to update the firmware.
59 +* In the opened window, click the “Bootloader” button. The device will reboot and will be waiting commands to update the firmware.
58 58  
59 -[[image:1740740038720-603.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="553" width="600"]]
61 +[[image:1733156153294-767.png||data-xwiki-image-style-alignment="center" height="425" width="648"]]
60 60  
61 61  * **Select the menu “Monitor - Stop” or click the “Stop” button to release the serial port and allow to use it for updating the firmware.**
62 62  
63 63  ~11. Return to the “Updater” window and click the “Update” button. The updating process will start.
64 64  
65 -12. Wait the updating process is finished. If using BMS USB-CAN, move the “+5V” switch to the “0” position. Disconnect the BMS Display device from the USB-CAN adapter.
67 +12. Wait the updating process is finished. Move the switches “+5V” and “Cells” to the “0” position and disconnect the BMS Logic device from the BMS USB-RS485.
1740739961052-896.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -12.1 KB
Content
1740740038720-603.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -49.9 KB
Content