Skip to Content

Changes for page 5. Firmware update

Last modified by Admin on 2025/02/28 11:48
From version 3.1
edited by Admin
on 2025/02/28 10:36
Change comment: Uploaded new attachment "1740739018136-732.png", version {1}
To version 1.4
edited by Admin
on 2025/02/28 10:31
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -21,30 +21,34 @@
21 21  2. Move switches of the BMS USB-CAN to the following positions:
22 22  
23 23  * 120 Ohm – “I”;
24 -* +5V – “0”.
24 +* +5V – “1”.
25 25  
26 26  3. Connect the BMS USB-CAN to a PC.
27 27  
28 -4. Move the switch “+5V” of the BMS USB-CAN to “I”. Check that the led of the BMS Display is blinking.
28 +4. Move the switches “Cells” and “+5V” of the BMS USB-RS485 to “I”. Check that the led “DS1” of the BMS Logic 12/18 is blinking.
29 29  
30 30  5. Open the Device Manager* and determine a name of an appeared serial port (Click the right mouse button on the Start menu and select the “Device Manager” item):
31 31  
32 -[[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153285-215.png||data-xwiki-image-style-alignment="center" height="377" width="382"]]
32 +[[image:1733156153285-215.png||data-xwiki-image-style-alignment="center" height="377" width="382"]]
33 33  
34 34  6. Install and launch the ElectricDeviceMonitor.
35 35  
36 36  7. Click the “Updater” button:
37 37  
38 -[[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153290-392.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
38 +[[image:1733156153290-392.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
39 39  
40 -8. Select the transport “CAN transport (BMS USB-CAN) (1.0.0)” and click the “Settings” button to configure the adapter: select a port name that corresponds to the BMS USB-CAN and 250 kbit/s baud rate.
40 +8. Select the transport “Serial port transport (1.0.0)” and click the “Settings” button to configure the serial port: select a port name that corresponds to the BMS USB-RS485 and 115200 kbps baud rate.
41 41  
42 -[[image:1740738923079-336.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
42 +[[image:1733156153292-532.png||data-xwiki-image-style-alignment="center" height="318" width="298"]]
43 43  
44 -9. Click the “Browse…” button and open the new firmware file in .srec format.
44 +9. Click the “Browse…” button and open the new firmware file.
45 45  
46 46  **10. Boot the device to go into the bootloader mode.**
47 47  
48 +**10a.** For the **BMS Logic 12 v3.3 and older** or **BMS Logic 18 v3.2 and older** (which have an address switch onboard):
49 +
50 +* Move all switches to the OFF state so the address is 0. The device will show that it is in the bootloader mode by flashing the DS1 with 0.5Hz frequency.
51 +
48 48  **10b.** For the **BMS Logic 12 v3.4 and newer** or **BMS Logic 18 v3.3 and newer** do the following steps:
49 49  
50 50  * In the ElectricDeviceMonitor, select the menu “Tasks – Monitor - BMS Logic 12/18 3.x”:
1740738923079-336.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -6.2 KB
Content
1740739018136-732.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -33.1 KB
Content