Skip to Content

Changes for page 5. Firmware update

Last modified by Admin on 2025/02/28 11:48
From version 14.1
edited by Admin
on 2025/02/28 11:37
Change comment: There is no comment for this version
To version 13.2
edited by Admin
on 2025/02/28 11:32
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -19,7 +19,7 @@
19 19  
20 20  ~1. Connect the BMS IMD to the USB-CAN adapter.
21 21  
22 -2. If BMS USB-CAN used, move switches of the  to the following positions:
22 +2. Move switches of the  to the following positions:
23 23  
24 24  * 120 Ohm – “I”;
25 25  * +5V – “0”.
... ... @@ -26,9 +26,9 @@
26 26  
27 27  3. Connect the USB-CAN adapter to a PC.
28 28  
29 -4. Power up the BMS IMD device. Check that the led of the BMS IMD is blinking.
29 +4. Move the switch “+5V” of the BMS USB-CAN to “I”. Check that the led of the BMS IMD is blinking.
30 30  
31 -5. If BMS USB-CAN used, open the Device Manager and determine a name of an appeared serial port (Click the right mouse button on the Start menu and select the “Device Manager” item):
31 +5. Open the Device Manager* and determine a name of an appeared serial port (Click the right mouse button on the Start menu and select the “Device Manager” item):
32 32  
33 33  [[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153285-215.png||data-xwiki-image-style-alignment="center" height="377" width="382"]]
34 34  
... ... @@ -38,9 +38,9 @@
38 38  
39 39  [[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153290-392.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
40 40  
41 -8. Select the corresponding USB-CAN adapter in a drop-down list and click the “Settings” button to configure the adapter:
41 +8. Select the "CAN transport (BMS USB-CAN) (1.0.0)" in a drop-down list and click the “Settings” button to configure the adapter:
42 42  
43 -* select device or port name that corresponds to the USB-CAN adapter;
43 +* select port name that corresponds to the BMS USB-CAN;
44 44  * set 250 kbit/s baud rate.
45 45  
46 46  [[image:1740738923079-336.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
... ... @@ -51,21 +51,21 @@
51 51  
52 52  * In the ElectricDeviceMonitor, select the menu “Tasks – Monitor - BMS IMD 1.x”:
53 53  
54 -[[image:Battery management systems.BMS Main 3.3\. Configuration.3\.1 General information.WebHome@1735233230234-960.png||alt="I1735233230234-960.png" data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="340" width="450"]]
54 +[[image:1740739041707-667.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="295" width="300"]]
55 55  
56 -* Select the corresponding USB-CAN apater and set the following connection settings and click the “Launch” button:
57 -** device or port name that corresponds to the USB-CAN adapter;
56 +* Set the following connection settings and click the “Launch” button:
57 +** port name that corresponds to the BMS USB-CAN;
58 58  ** baud rate: 250 kbit/s;
59 -** BMS IMD address (22 by default).
59 +** BMS IMD Node ID (20 by default).
60 60  
61 -[[image:1740741924108-471.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="247" width="450"]]
61 +[[image:1740739961052-896.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="237" width="450"]]
62 62  
63 63  * In the opened window, click the “Send” button under "Reset and start bootloader" section. The device will reboot and will be waiting commands to update the firmware.
64 64  
65 -[[image:1740742073165-496.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="397" width="600"]]
65 +[[image:1740740038720-603.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="553" width="600"]]
66 66  
67 67  * **Select the menu “Monitor - Stop” or click the “Stop” button to release the serial port and allow to use it for updating the firmware.**
68 68  
69 69  ~11. Return to the “Updater” window and click the “Update” button. The updating process will start.
70 70  
71 -12. Wait the updating process is finished. Disconnect the BMS IMD device from the USB-CAN adapter.
71 +12. Wait the updating process is finished. Move the “+5V” switch to the “0” position. and disconnect the BMS IMD device from the BMS USB-CAN.