Skip to Content

Changes for page 5. Firmware update

Last modified by Admin on 2025/02/28 11:48
From version 13.2
edited by Admin
on 2025/02/28 11:32
Change comment: There is no comment for this version
To version 2.1
edited by Admin
on 2025/02/28 10:35
Change comment: Uploaded new attachment "1740738923079-336.png", version {1}

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -Battery management systems.BMS IMD.WebHome
1 +Battery management systems.BMS Display.WebHome
Content
... ... @@ -1,32 +1,31 @@
1 -(% data-numbered-headings-start="5" style="--numbered-headings-start: 4;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
1 +(% data-numbered-headings-start="4" style="--numbered-headings-start: 3;font-size: 0px;color: rgba(0, 0, 0, 0.0);margin-bottom: 0px; margin-top: 0px;" %)
2 2  = Firmware update =
3 3  
4 4  == Introduction ==
5 5  
6 -The document describes the steps to update the BMS IMD firmware.
6 +The document describes the steps to update the BMS Display firmware.
7 7  
8 8  Required hardware and software:
9 9  
10 10  * PC or laptop with Windows 10 or newer;
11 -* BMS USB-CAN – a device to power up and communicate with the BMS IMD;
12 -** Also Systec, PEAK and Marathon USB-CAN adapters are supported;
11 +* BMS USB-CAN – a device to power and communicate with the BMS Display;
13 13  * [[ElectricDeviceMonitor>>https://movicomelectric.com/wa-data/public/site/app/ElectricDeviceMonitorSETUP.exe]] – a software to monitor and configure devices by Movicom Electric;
14 -* Firmware (*.srec) – a new firmware for the BMS IMD.
13 +* Firmware (*.srec) – a new firmware for the BMS Display.
15 15  
16 16  == Updating process ==
17 17  
18 18  Follow the steps below:
19 19  
20 -~1. Connect the BMS IMD to the USB-CAN adapter.
19 +~1. Connect the BMS Display to the BMS USB-CAN.
21 21  
22 -2. Move switches of the  to the following positions:
21 +2. Move switches of the BMS USB-CAN to the following positions:
23 23  
24 24  * 120 Ohm – “I”;
25 25  * +5V – “0”.
26 26  
27 -3. Connect the USB-CAN adapter to a PC.
26 +3. Connect the BMS USB-CAN to a PC.
28 28  
29 -4. Move the switch “+5V” of the BMS USB-CAN to “I”. Check that the led of the BMS IMD is blinking.
28 +4. Move the switch “+5V” of the BMS USB-CAN to “I”. Check that the led of the BMS Display is blinking.
30 30  
31 31  5. Open the Device Manager* and determine a name of an appeared serial port (Click the right mouse button on the Start menu and select the “Device Manager” item):
32 32  
... ... @@ -38,34 +38,37 @@
38 38  
39 39  [[image:Battery management systems.BMS Logic 12.4\. Firmware update.WebHome@1733156153290-392.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
40 40  
41 -8. Select the "CAN transport (BMS USB-CAN) (1.0.0)" in a drop-down list and click the “Settings” button to configure the adapter:
40 +8. Select the transport “CAN transport (BMS USB-CAN) (1.0.0)” and click the “Settings” button to configure the serial port: select a port name that corresponds to the BMS USB-CAN and 115200 kbps baud rate.
42 42  
43 -* select port name that corresponds to the BMS USB-CAN;
44 -* set 250 kbit/s baud rate.
42 +[[image:1733156153292-532.png||data-xwiki-image-style-alignment="center" height="318" width="298"]]
45 45  
46 -[[image:1740738923079-336.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true"]]
44 +9. Click the “Browse…” button and open the new firmware file.
47 47  
48 -9. Click the “Browse…” button and open the new firmware file in .srec format.
49 -
50 50  **10. Boot the device to go into the bootloader mode.**
51 51  
52 -* In the ElectricDeviceMonitor, select the menu “Tasks – Monitor - BMS IMD 1.x”:
48 +**10a.** For the **BMS Logic 12 v3.3 and older** or **BMS Logic 18 v3.2 and older** (which have an address switch onboard):
53 53  
54 -[[image:1740739041707-667.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="295" width="300"]]
50 +* Move all switches to the OFF state so the address is 0. The device will show that it is in the bootloader mode by flashing the DS1 with 0.5Hz frequency.
55 55  
52 +**10b.** For the **BMS Logic 12 v3.4 and newer** or **BMS Logic 18 v3.3 and newer** do the following steps:
53 +
54 +* In the ElectricDeviceMonitor, select the menu “Tasks – Monitor - BMS Logic 12/18 3.x”:
55 +
56 +[[image:1733156153292-595.png||data-xwiki-image-style-alignment="center" height="320" width="296"]]
57 +
56 56  * Set the following connection settings and click the “Launch” button:
57 -** port name that corresponds to the BMS USB-CAN;
58 -** baud rate: 250 kbit/s;
59 -** BMS IMD Node ID (20 by default).
59 +** serial port name of the BMS USB-RS485
60 +** baud rate and data format: 115200 kbps, 8 bits, no parity, 1 stop bit
61 +** address – 247
60 60  
61 -[[image:1740739961052-896.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="237" width="450"]]
63 +[[image:1733156153293-550.png||data-xwiki-image-style-alignment="center" height="227" width="410"]]
62 62  
63 -* In the opened window, click the “Send” button under "Reset and start bootloader" section. The device will reboot and will be waiting commands to update the firmware.
65 +* In the opened window, click the “Bootloader” button. The device will reboot and will be waiting commands to update the firmware.
64 64  
65 -[[image:1740740038720-603.png||data-xwiki-image-style-alignment="center" data-xwiki-image-style-border="true" height="553" width="600"]]
67 +[[image:1733156153294-767.png||data-xwiki-image-style-alignment="center" height="425" width="648"]]
66 66  
67 67  * **Select the menu “Monitor - Stop” or click the “Stop” button to release the serial port and allow to use it for updating the firmware.**
68 68  
69 69  ~11. Return to the “Updater” window and click the “Update” button. The updating process will start.
70 70  
71 -12. Wait the updating process is finished. Move the “+5V” switch to the “0” position. and disconnect the BMS IMD device from the BMS USB-CAN.
73 +12. Wait the updating process is finished. Move the switches “+5V” and “Cells” to the “0” position and disconnect the BMS Logic device from the BMS USB-RS485.
1740739018136-732.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -33.1 KB
Content
1740739041707-667.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -33.2 KB
Content
1740739961052-896.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -12.1 KB
Content
1740740038720-603.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -49.9 KB
Content
1740741924108-471.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -15.7 KB
Content
1740742073165-496.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.admin
Size
... ... @@ -1,1 +1,0 @@
1 -45.3 KB
Content