| ... |
... |
@@ -1,8 +1,8 @@ |
| 1 |
1 |
= General information = |
| 2 |
2 |
|
| 3 |
|
-[[image:1734100330351-605.png||data-xwiki-image-style-alignment="center" height="178" width="300"]] |
|
3 |
+[[image:1772028538915-371.0a.png||data-xwiki-image-style-alignment="center" height="166" width="300"]] |
| 4 |
4 |
|
| 5 |
|
-(% id="cke_bm_1181S" style="display:none" %) (%%)BMS GSM is an extension module that can be inserted to the BMS Mini, BMS Mini S, BMS Main 3, BMS Main X or BMS Main 3X controller. It allows a BMS controller to send battery data to a remote server over a cellular network. |
|
5 |
+(% id="cke_bm_1181S" style="display:none" %) (%%)BMS GSM is an extension module that can be inserted to the BMS Mini, BMS Mini S, BMS Main 2R, BMS Main X, BMS Main 3 or BMS Main 3X controller. It allows a BMS controller to send battery data to a remote server over a cellular network. |
| 6 |
6 |
|
| 7 |
7 |
Figure below shows the overall architecture of a battery system that is controlled wirelessly by an upper-level system. |
| 8 |
8 |
|
| ... |
... |
@@ -13,10 +13,10 @@ |
| 13 |
13 |
|**Parameter**|**Value** |
| 14 |
14 |
|Supply voltage, V|5.0 ± 0.5 |
| 15 |
15 |
|Current consumption in the idle state, mA, max|80 |
| 16 |
|
-|Current consumption in the active state, mA, avg|500 |
| 17 |
|
-|Supported network types|GSM/GPRS/EDGE, NB-IoT |
| 18 |
|
-|Dimensions (length × width × height), mm|61 × 54 × 15 |
| 19 |
|
-|Weight, g|23 ± 2 |
|
16 |
+|Current consumption in the active state, mA, avg|400 |
|
17 |
+|Supported network types|GSM/GPRS/EDGE/LTE |
|
18 |
+|Dimensions (length × width × height), mm|58 × 58 × 15 |
|
19 |
+|Weight, g|23 ± 5 |
| 20 |
20 |
|(% colspan="2" %)**Operating conditions** |
| 21 |
21 |
|Operating temperature range, ° С|-40 to +85 |
| 22 |
22 |
|Degree of protection from external influences|IP00 |
| ... |
... |
@@ -26,22 +26,25 @@ |
| 26 |
26 |
(% class="box warningmessage" %) |
| 27 |
27 |
((( |
| 28 |
28 |
**Attention** |
| 29 |
|
-Connecting the BMS GSM 1.x is performed to the powered-off BMS controller! |
|
29 |
+Connecting the BMS GSM is performed to the powered-off BMS controller! |
|
30 |
+To prevent the damage of device avoid electrostatic discharges. |
| 30 |
30 |
))) |
| 31 |
31 |
|
| 32 |
32 |
The BMS GSM must be inserted into the corresponding header of the BMS controller. The device must be fixed to the BMS controller by **11mm M3 standoffs** and M3 screws. |
| 33 |
33 |
|
| 34 |
|
-Here is the example of BMS Wi-Fi header on BMS Main X: |
|
35 |
+Here is the example of header for additional devices on BMS Main X: |
| 35 |
35 |
|
| 36 |
|
-[[image:1734099661846-836.png||data-xwiki-image-style-alignment="center" height="423" width="450"]] |
|
37 |
+[[image:1734100655472-941.png||data-xwiki-image-style-alignment="center" height="423" width="450"]] |
| 37 |
37 |
|
| 38 |
38 |
Before configuring the device, a SIM card of the cellular operator must be inserted into the holder on the device board. |
| 39 |
39 |
|
| 40 |
40 |
= Configuration = |
| 41 |
41 |
|
| 42 |
|
-Configuring the BMS GSM 1.x must be done according to the BMS controller’s configuration manual. Typically, the connection settings are in the “Connectivity -> GSM” section of the BMS controller. |
|
43 |
+Configuring the BMS GSM must be done according to the BMS controller’s configuration manual, see [[Battery management systems>>path:/bin/view/Battery%20management%20systems/]]. |
| 43 |
43 |
|
| 44 |
|
-(% class="box warningmessage" %) |
|
45 |
+Typically, the connection settings located in the “Connectivity -> GSM” section of the BMS controller. |
|
46 |
+ |
|
47 |
+(% class="box infomessage" %) |
| 45 |
45 |
((( |
| 46 |
46 |
To apply new connection settings, it is necessary to restart the BMS controller. |
| 47 |
47 |
))) |
