Changes for page 2. Strings controllers: signals and errors
Last modified by Admin on 2025/02/21 14:51
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -65,52 +65,10 @@ 65 65 Here is the list of error of BMS Main 3. 66 66 67 67 68 -|Name |Description|Set up by|Used by| 69 -|Overcurrent| | | | 70 -|Undervoltage| | | | 71 -|Overvoltage| | | | 72 -|Low temperature (DCH) | temperature is too low for discharging;| | | 73 -|High temperature (DCH) | temperature is too high for discharging;| | | 74 -|Battery cover error | battery cover is open;| | | 75 -|High humidity | humidity of the battery is increased;| | | 76 -|Water | there is water in the battery enclosure;| | | 77 -|High Logic temperature | at least one of the Logic devices is overheated;| | | 78 -|Logic offline | at least one of the Logic devices is offline;| | | 79 -|Critical error;| | | | 80 -|Crown error | connection with a Crown forklift is lost;| | | 81 -|Cell count error | number of cells does not match the specified value;| | | 82 -|HYG offline | connection with a HYG forklift is lost;| | | 83 -|Need acknowledge | there is an unacknowledged error in Error journal;| | | 84 -|Combilift offline | connection with a Combilift forklift is lost;| | | 85 -|Short circuit| | | | 86 -|High contactor temperature| | | | 87 -|ADC error | current cannot be measured;| | | 88 -|Current sensor error | error in the current sensor circuit;| | | 89 -|CH contactor cycles error | switching frequency of the charging contactor is too high;| | | 90 -|DCH contactor cycles error | switching frequency of the discharging contactor is too high;| | | 91 -|Shunt offline | connection with the shunt current sensor is lost;| | | 92 -|Shunt error | internal error of the shunt current sensor;| | | 93 -|WDT reset | watchdog timer reset the device;| | | 94 -|No temperature sensors | the device has no temperature sensors connected;| | | 95 -|Temperature sensor is shorted | some temperature sensors are shorted;| | | 96 -|Spirit offline | connection with a Spirit forklift is lost;| | | 97 -|Low temperature (CH) | temperature is too low for charging;| | | 98 -|High temperature (CH) | temperature is too high for charging;| | | 99 -|Unallowable charging | charging the battery through the discharging contactor;| | | 100 -|Stuck contactor;| | | | 101 -|CH contactor feedback error | the control signals for the charging contactor and the contactor feedback differ;| | | 102 -|DCH contactor feedback error | the control signals for the discharging contactor and the contactor feedback differ;| | | 103 -|Insulation fault;| | | | 104 -|PCH contactor feedback error | the control signals for the precharging contactor and the contactor feedback differ;| | | 105 -|CH/DCH contactor feedback error | the control signals for the charging/discharging contactor and the contactor feedback differ;| | | 106 -|Main contactor feedback error | the control signals for the main contactor and the contactor feedback differ;| | | 107 -|General error| | | | 108 -|High voltage fault | failure of high voltage measuring circuits;| | | 109 -|Power switch error | short circuit in contactor coil control circuit or power switch overheating;| | | 110 -|HVIL error | breakage of high-voltage interlock current loop;| | | 111 -|Precharge error | capacitive load pre-charge process did not end during the estimated time;| | | 112 -|Power fault | external devices power supply error: current sensors, HVIL, BMS Logic or CAN2 (int) bus powered devices;| | | 113 -|Current limit error | charging or discharging current is more than limit calculated by Charge map or Discharge map.| | | 68 +|((( 69 +(% style="width:1227px" %) 70 +|(% colspan="1" rowspan="2" style="width:216px" %)**Name**|(% colspan="1" rowspan="2" style="width:321px" %)**Description**|(% colspan="1" rowspan="2" style="width:258px" %)**Set up by**|(% rowspan="2" style="width:258px" %)**Used by** 71 +)))| | 114 114 | | | | | 115 115 | | | | | 116 116 | | | | |